Diese Übersetzung enthält möglicherweise noch nicht die neuesten Änderungen der Original-Anleitung. Hilf mit, die Übersetzung zu aktualisieren oder sieh dir die Original-Anleitung an.
Einleitung
Wenn du Probleme mit der USB-Verbindung hast, musst du möglicherweise den USB-Anschluss ersetzen. Dies ist eine Anleitung zum Austauschen des USB-Anschlusses bei der Hero 4 Black.
Was du brauchst
-
-
Zunächst musst du die Frontplatte entfernen, indem du vorsichtig mit dem Hebelwerkzeug um die Kante herum fährst, und die Clips löst.
-
Nach Lösen der Clips am Rand die Frontplatte abziehen.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Now, you will need to take a PH000 Philips head screwdriver and remove the 4 corner screws.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Now, you will need to remove the camera and boards from the black plastic housing. You may use any tool that will do the job. My group found out, if you use the plastic tool to remove the boards and camera, that it would assist you with the removal.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the ribbon strip by carefully pulling on it. It should slide out of its connection.
-
When you push down on the three wires that are connected to the clip. The clip will disconnect from the motherboard.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Take yourPH000 Philips head screwdriver to remove the four screws outlined in red.
-
Once the screws are removed. Gently remove the board and as you lift the board, the computer chip (outlined in orange) will separate from the motherboard.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Take your PH000 Philips head screwdriver and remove the three screws that are outlined in red.
-
Just like before, gently pull up on the ribbon strip to remove the connector from the motherboard.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the two screws to remove the riser that is being held in place by the screws.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove a single screw located near the barcode.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
At the top of the ribbon strip, there is a black clip that will need to be popped up.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Gently, grab the ribbon with a pair of tweezers to disconnect the ribbon from the connecter.
-
Now, the motherboard can be removed. Due to the USB connector being soldered to the motherboard, the entire board will need to be replaced.
-
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
8 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
35%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›