Diese Übersetzung enthält möglicherweise noch nicht die neuesten Änderungen der Original-Anleitung. Hilf mit, die Übersetzung zu aktualisieren oder sieh dir die Original-Anleitung an.
Einleitung
Diese Anleitung zeigt dir, wie du den Hauptlautsprecher am Google Pixel 2 XL austauschen kannst.
Was du brauchst
-
-
Setze ein SIM Auswurfwerkzeug oder eine aufgebogene Büroklammer in das kleine Loch im SIM Einschub ein. Du findest ihn an der linken Seitenkante des Smartphones, gegenüber der Einschalttaste und der Lautstärketasten.
-
Drücke es fest hinein, damit der SIM Einschub herausspringt.
-
-
Schritt 3 Google Pixel 2 XL öffnen
Achtung: Die Schritte 3-14 stammen von einer Anleitung, die derzeit bearbeitet wird.
-
Setze einen Saugheber so nahe wie möglich an der Kante mit dem SIM Einschub an, vermeide aber den gebogenen Teil nahe der Kante.
Shouldn’t this be “As close as possible to the volume rocker”?
Forget about the tiny toy suction cup they provide to battery replacement kits. I used a dent puller from an automotive shop. The smallest they had was just small enough for the Pixel's screen. I still needed to heat the edges with a heat gun.
I wish someone tell me in advance that if I doing this replacement after using phone for a few years it better to have spare "display adhesive" and be ready to follow Google Pixel 2 XL Displayklebestreifen anbringen
Original adhesive become dirty with time and fat chances it will be damaged during opening phase. In my case I replaced battery but can't use the phone, as still waiting for adhesive to be delivered -
-
-
Ziehe mit festem und konstanter Kraft am Saugheber und setze ein Plektrum zwischen Frontpanel und rückwärtigem Gehäuse ein.
Whatever happened to “Do not heat your phone. If needed, you can use a dropper or syringe to inject isopropyl alcohol (90+%) around the edges of the back cover to weaken the adhesive.”?
It is in concern with swollen batteries.
I spent an hour trying to get the glass screen apart from the body. I tried the hairdryer etc but made no progress. However, when I used a sucker to gently pull on the glass it was easy.
I used a heat gun, and the metal spatula in the iFixit kit. I broke the screen. Then, continuing with a blue plastic triangle, the screen continued to break. It seems to be quite brittle.
Never use metal tools on glass component
p43j77 -
Just broke the screen as well. I’d say heat gun is a must, otherwise it’s really hard to slide pick at the top and bottom without breaking the screen. It’s a very thin line of glass over there.
I thought I did this perfectly. I used the iOpener to heat the glue, and the picks to slide around the screen to release the adhesive. I preformed the rest of the repair (charging assembly and the battery) with little issue. Just reassembled and the volume rocker side of the screen is white. I took less care on this side since the instructions said that you didn’t need to worry about how far the pick went in. NOT TRUE! There is a curvature to that edge that will push your pick up into the back of the unprotected display. It clearly doesn’t take much to damage it. I was so careful! F&CK!! I should have just created the e-waste and bought a new device. So mad!
-
-
-
Setze das Plektrum nicht tiefer als 6 mm an der Unterkante des Smartphones ein. Wenn das Plektrum den gefalteten Teil des OLED Panels trifft, kann das Display beschädigt werden.
-
Schneide nicht an der linken Kante, hier können empfindliche Displaykabel beschädigt werden.
-
Führe nur sehr flache Schnitte in der oberen linken Ecke, wenn du hier tiefer schneidest, kannst du die Frontkamera beschädigen.
-
-
-
Schiebe das Plektrum an der rechten Seite nach unten, um die Klebeverbindung am Display zu trennen.
-
-
-
Führe das Plektrum um die rechte untere Ecke und an der Unterkante des Smartphones entlang.
-
-
-
Setze das Plektrum dann wieder an der oberen rechten Ecke des Smartphones ein und schiebe es um die Ecke und entlang der Oberkante.
-
-
-
Hebe das Display an der rechten Seite vorsichtig an, so wie man ein Buch öffnet.
-
Lege das Display sorgfältig flach auf den Tisch, direkt neben das restliche Smartphone. Halte es so dicht wie möglich am Smartphone, um zu vermeiden, dass die Kabel des Displays und des Touchscreens zu sehr angespannt werden.
-
-
-
-
Heble mit der Ecke eines Plastiköffnungswerkzeugs die untere Kante der Abdeckung über dem Stecker am Touchscreen-Kabel hoch und löse sie ab.
-
Entferne die Abdeckung über dem Stecker.
Lol mine shot off and Ricocheted off the ceiling! Then landed on my shoulder haha
It literally popped me right in the middle of the forehead. My wife is still making fun of me.
Mine flew off while I was laughing you guys, never too be seen again: (
I decided to work outdoors, didn't read any comments first, so when mine flew off I found it five cursing minutes later in a crack on the driveway. Should have read the comments first! Thanks hamiltont. Will now read every comment BEFORE attempting step.
Confirmed, this $@$* can fly!
-
-
-
Hebe den Stecker am Touchscreenkabel mit der Spudgerspitze aus seinem Anschluss auf der Hauptplatine.
This small connector gave me fits getting it located correctly, is there a trick to getting it aligned since it’s difficult to see around edge of the connector?
-
-
-
Löse einen eventuell vorhandenen Aufkleber auf der Abdeckung des Displaysteckers mit einer Pinzette ab.
-
-
-
Setze die Spudgerspitze in das kleine Loch an der Kante der Abdeckung des Displaysteckers ein.
-
Hole die Abdeckung mit dem Spudger aus ihrer Vertiefung heraus.
-
Entferne die Abdeckung des Steckers.
-
-
-
Hebe den Displaykabelstecker mit dem flachen Ende des Spudgers aus seinem Anschluss heraus.
-
Entferne das Display.
BE EXTRA CAREFUL HERE, and during reassembly! There are 2 itty bitty parts directly under this ribbon cable connector that, if damaged, will render your loudspeaker unusable. The only sure way to fix it if you break it is to replace the motherboard. There are some reports of people being able to solder the spots and shorting it to make it work, and that worked for me for a time, but they’re really tiny (about 0.5 mm) and if you don’t get a secure solder, or if you bleed over, it will also mess up your top speaker.
Saw this comment after I’ve done replacing and sure enough, the loud speaker was broken. The resistor was knocked over but still hanging in place so I just stuck it back and it works for now.
They are 2 black resistors at the end of the cable’s connector. So follow the above photo exactly and pry the connector from the side, not from the end of the connector like I did
What wasn't clear to me here (because I didn't put Step 13 together with Step 12, I suppose?) is that if your replacement part came with speaker grills and camera gasket, Step 12 is your final step. You are done, except for replacing the cables and covers, then placing the adhesive strips onto the replacement part and sticking the phone back together.
I ordered my screen from iFixit and it came with new grills and camera gasket already installed. I was able to use the thinnest strips on the supplied Tesa patch to line the entire screen perimeter piecemeal, then stick it back together like new.
-
-
In diesem Schritt verwendetes Werkzeug:Magnetic Project Mat$19.95
-
Entferne elf 3,8 mm Kreuzschlitzschrauben, mit denen der Mittelrahmen befestigt ist.
-
-
-
Setze ein Plastiköffnungswerkzeug in die Kerbe im Mittelrahmen in der Nähe der Lautstärketasten ein. Heble den Mittelrahmen hoch und vom restlichen Smartphone weg.
-
Entferne den Mittelrahmen.
How do I reattach the midframe? it seems like there are a lot of tabs that need to be reinserted carefully
Slide in the bottom part at an angle in first since it has some tabs. Otherwise it will get stuck halfway on top
-
-
-
Löse den Stecker der Frontkamera mit der Spudgerspitze ab.
-
-
-
Löse den Stecker am rechten Active Edge Sensor mit dem flachen Ende des Spudgers ab.
Also disconnect the antenna cable just to the right of the right Active Edge sensor connector
-
-
-
Löse den Stecker am linken Active Edge Sensor mit dem flachen Ende des Spudgers ab.
-
-
-
Überprüfe nochmal, ob alle Stecker und Kabel von der Hauptplatine getrennt sind. Hebe dann die Hauptplatine unten vorsichtig mit dem flachen Ende des Spudgers an.
-
Halte den breiten Teil der Hauptplatine in der Nähe des SIM Einschubs fest und schiebe die Platine zur Unterkante des Smartphones, während du es gleichzeitig aus dem Smartphone heraushebst.
-
Entferne die Hauptplatine.
Agreed. No mention of the antenna cable.
-
-
-
Schiebe die Spudgerspitze unter die untere linken Seite des Lautsprechers und heble die Lautsprechereinheit aus dem Smartphone hoch.
This step was very difficult, I believe I just snapped the loudspeaker to the left of silver oval piece
I was just able to remove the loud speaker using the directions provided. The piece sprung out of the phone. The bottom of the piece is flat with pieces of metal and it appears to be slightly bent from my prying. We will see if it still works.
I ended up using my metal silver spudger. It goes in farther without prying on the fragile plastic. I’m replacing the charging circuit anyway, so not too worried about minor damage
This is a difficult step. Pictures indicating other safe pry points would be helpful.
Most stubborn component to remove.
I was able to remove this without great stress on the part by inserting my right thumbnail (thumbprint facing the battery / top of the phone) in between the loudspeaker and the phone body above the silver oval, while at the same time using my left index fingernail to gently lift the long left side protrusion of the loudspeaker. Note that the plastic opening picks were too thick for this. Took twenty minutes or more to figure this out, but about two minutes or less to do it. The fundamental problem seems to be that this part is friction-fit into place, and you won’t get it out all in one motion without risk of breaking it, you have to work at it alternately from every angle. I also added a few drops of everclear (95% ethanol, isopropyl was hard to come by because of COVID), which may or may not have mattered (I have no control for this experiment). I believe there was no damage to the part.
-
Vergleiche dein Ersatzteil mit dem Originalteil. Du musst vielleicht vor dem Zusammenbau fehlende Teile vom alten auf das neue Teil übertragen oder Schutzfolien vom Neuteil abziehen.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Entsorge deinen Elektromüll fachgerecht.
Hat die Reparatur nicht den gewünschten Erfolg gebracht? Unsere Antwortcommunity kann dir weiterhelfen.
Vergleiche dein Ersatzteil mit dem Originalteil. Du musst vielleicht vor dem Zusammenbau fehlende Teile vom alten auf das neue Teil übertragen oder Schutzfolien vom Neuteil abziehen.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Entsorge deinen Elektromüll fachgerecht.
Hat die Reparatur nicht den gewünschten Erfolg gebracht? Unsere Antwortcommunity kann dir weiterhelfen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
7 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
83%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
2 Kommentare
Does this method work with the earpiece one as well?
We don’t have official instructions out for the earpiece speaker, but it’s only accessible underneath the glass panel and antenna assembly on the back of the phone so removing it is a bit different. After removing the motherboard you would have to lift this flex cable from the back of the phone, just enough to separate it from the adhesive holding it down. Then you can carefully pry up the glass panel, and remove antenna assembly and the earpiece speaker underneath. You’ll probably need an iOpener, suction cup, and opening picks to remove the panel and everything underneath—they’re all glued down pretty solidly.