Diese Übersetzung enthält möglicherweise noch nicht die neuesten Änderungen der Original-Anleitung. Hilf mit, die Übersetzung zu aktualisieren oder sieh dir die Original-Anleitung an.
Einleitung
Diese Anleitung zeigt dir, wie du ein zersprungenes Rückseitenglas austauschen kannst. Vielleicht willst du auch nur die Farbe ändern?
Was du brauchst
-
-
Erwärme einen iOpener und lege ihn zwei Minuten lang auf die Glasrückseite des Smartphones.
-
-
-
Wenn das Glas warm anfühlt, dann setze einen Saugheber nahe an der Kante an.
-
Ziehe den Saugheber hoch und setze ein Plektrum in den Spalt ein.
The suction cup method did not work for me at all. Even after applying heat worrisomely long with a hairdryer the glass wouldn't budge. Maybe if I'd had a better or bigger suction cup it could've. I bought a kit from a local store and the suction cup was smaller than iFixit's.
One thing to mention is that it's really hard to try and hold the phone down while pulling the suction cup. And then you'd need a third hand to try and slide a pick in there. Seems pretty impossible for one person to accomplish without something not covered in this guide to be honest.
The solution was to start from the corner that was broken, taking out one bit first and then lifting up next to that, causing the glass to break into smaller sections and just going from there bit by bit.
Also a good technique I found was to use the hairdryer while pulling out the bits which loosens up the glue while you're pulling out a piece (especially a bigger one).
-
-
-
Trenne mit dem Plektrum den Kleber rings um den Rand der Glasscheibe auf.
-
Wenn das Auftrennen schwergängig wird, dann erwärme erneut.
be careful- you can easily rip/slice the NFC antenna ribbon with the pick. the Pixel and Pixel XL have NFC ribbon adhered to the underside of the very adhesive you are trying to peel up. In the photo for step 6 you can see the black rectangular ribbon that surrounds the fingerprint scanner. Perhaps i didn’t heat long enough or i was too aggressive or the cracks in my glass offered different angles of attack for the pick. Either way, exercise caution. It might be recommended to try to insert the pick straight down from the top center of the glass so that the pick tip glances over the rounded edge of ribbon going into the phone. (see the wide slit above fingerprint scanner in step 6 photo)
Hey Austin,
Thanks for the feedback! I’ll add a warning to this step.
-
-
-
Wenn du die Glasscheibe um den Fingerabdrucksensor ablöst, dann drücke den Sensor fest nach unten, bis er sich vom Rückseitenglas trennt.
-
Schneide die Klebeverbindung unter dem Rückseitenglas weiter auf, bis du die Glasscheibe entfernen kannst.
There is some kind of a filter/grille/grating covering the (what I think is the) focus on the right side of the two black holes. You probably should be careful removing that (I believe it's glued into the glass) and transfer it to your replacement glass if it doesn't have that (none of the replacement glasses in pics/videos I've seen have had it). The glue in it was good enough that I just pressed it down to my replacement glass. I'd post a pic but it isn't possible here apparently.
Hi Fensi,
Thanks for the feedback! I added a step to cover what you mentioned.
-
-
-
-
Nimm ein Plektrum und eine Pinzette, heble das Gewebe damit behutsam hoch und entferne es.
-
-
-
Schabe mit einem Spudger oder einem Plastiköffnungswerkzeug alle Klebstoffreste vom Rahmen ab.
-
Wische die letztem Reste mit hochkonzentriertem Isopropylalkohol (mehr als 90%) ab.
-
-
-
Ziehe die weiße Schutzfolie von der beiliegenden Klebefolie ab. Achte darauf, dass du alle Ausschnitte heraustrennst.
-
Richte die Unterkante der Klebefolie an der Unterkante der Ersatzglasscheibe aus.
-
Lege die Klebefolie langsam auf die Glasscheibe ab.
-
Reibe die Klebefolie mit den Fingern auf der Glasscheibe fest, so dass sie gut haftet.
-
-
-
Drücke die Linse mit dem Finger oder einem Spudger fest von der Außenseite der Glasscheibe hinein (das ist die Seite, die am Smartphone normalerweise sichtbar ist), bis sie sich aus ihrer Vertiefung löst.
-
Entferne die Linse und bringe sie an der Rückseite der neuen Glasscheibe an.
The lens has adhesive surrounding it on the metal frame that will get pressed against the back side of your glass to hold it still. You should either not remove it, or replace it e.g. with some of the adhesive from the old glass. Note that you should use a miniscule amount so that it fits (it's a very narrow ring of adhesive surrounding it on the original). Of course there might be differences between versions but this was the case for me.
-
-
-
Ziehe die Schutzfolie von der Klebstoffrückseite der Glasscheibe.
-
Richte die Glasscheibe an der Unterkante der Vertiefung aus.
-
Lege die Glasscheibe in die Vertiefung ab.
-
-
-
Lege ein paar schwere Bücher dreißig Minuten lang auf das Smartphone, damit der Kleber gut abbindet.
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Die Reparatur hat nicht den gewünschten Erfolg gebracht? Unsere Community kann dir weiterhelfen.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Die Reparatur hat nicht den gewünschten Erfolg gebracht? Unsere Community kann dir weiterhelfen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
16 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
85%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›