Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Take all paper out of the paper tray. Unplug the printer.

    • Remove the plastic printer-control panel on the top left.

    • Then, forcefully lift up the bottom of the panel while applying downward pressure with your thumb-as shown.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 2 : Schritt 2, Bild 2 von 2
    • With your other hand, slide the top of the panel towards the back of the printer.

    • Do not rip the white cable that connects the panel with the main body of the printer.

    • Disconnect the ribbon by pinching the blue tab and pulling away from the green circuit board.

    • Lift the panel free and set to the side.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Place the plastic opening tool between the plastic cover and the mount on the printer.

    • Pry the plastic cover towards the center of the printer.

    • Pull up on the cover to remove it from the printer-as shown.

    • Repeat the process on the other side.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • To remove the glass panel, take out the four 14 mm (1/2 inch) screws with a T10 Torx screwdriver.

    • Don't lift the glass panel completely off because there are cables plugged into the underside.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Disconnect the white cables from the green motherboard by pinching the cable where it connects to the green motherboard. Pull up, lightly.

    • Set the lower part of the printer aside.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Place the glass panel, face down, on a smooth surface.

    • Remove the 14 mm (1/2 in.) screw from the white plastic tab on the side of the panel with a T10 Torx screwdriver.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Remove the glass pane by carefully bending the plastic frame down from the side and sliding the glass pane out from the side.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Samuel Isbell

Mitglied seit: 10/09/12

10 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 9-18, Amido Fall 2012 Mitglied von Cal Poly, Team 9-18, Amido Fall 2012

CPSU-AMIDO-F12S9G18

4 Mitglieder

10 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 7

Letzte 30 Tage: 30

Insgesamt: 3,814