Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Store

Einleitung

The scanner glass for the HP Envy 5660 may receive cracks over time. This guide will help the user replace the scanner glass.

  1. Open the cartridge access area.
    • Open the cartridge access area.

  2. Remove the three 11.5 mm screws with a T10 bit.
    • Remove the three 11.5 mm screws with a T10 bit.

  3. Locate the cover hinge on the right side of the printer. Pull the hinge off of the scanner to allow the scanner to open to 90 degress. Pull the hinge off of the scanner to allow the scanner to open to 90 degress.
    • Locate the cover hinge on the right side of the printer.

    • Pull the hinge off of the scanner to allow the scanner to open to 90 degress.

  4. Remove the  12 mm screws on the left side of the printer with a T10 bit. Remove the  12 mm screws on the left side of the printer with a T10 bit.
    • Remove the 12 mm screws on the left side of the printer with a T10 bit.

  5. Remove the 11.5 mm screw with a T10 bit to release the spring-loaded hinge. Since this is a compression spring, the hinge will snap downwards as soon as it is loosened.
    • Remove the 11.5 mm screw with a T10 bit to release the spring-loaded hinge.

    • Since this is a compression spring, the hinge will snap downwards as soon as it is loosened.

  6. Pull the plastic side cover off of the printer. You may need to lift the printer and push the cover downwards as it is latched onto the bottom of the printer. Plastic opening tools or a metal spudger may also be used.
    • Pull the plastic side cover off of the printer.

    • You may need to lift the printer and push the cover downwards as it is latched onto the bottom of the printer.

    • Plastic opening tools or a metal spudger may also be used.

  7. Remove the five 11.5 mm screws located at the bottom of the scanner.
    • Remove the five 11.5 mm screws located at the bottom of the scanner.

    • Steps 3-6 were intended to create easier access to these screws. However, they will still be difficult to reach.

    • The top of the scanner will now easily pull off.

  8. Pry the old scanning glass up with a metal spudger. There are adhesives under the scanning glass. Be careful not to break the glass while removing it.
    • Pry the old scanning glass up with a metal spudger.

    • There are adhesives under the scanning glass. Be careful not to break the glass while removing it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Ryan Steakley

Mitglied seit: 23.01.2018

781 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S1-G6, Livingston Winter 2018 Mitglied von Cal Poly, Team S1-G6, Livingston Winter 2018

CPSU-LIVINGSTON-W18S1G6

4 Mitglieder

5 Anleitungen geschrieben

Remove an additional three 11.5 mm torx head screws in the same plane as step #4 photo, but near the hinges. This allows the cover hinges to be raised a bit for easier access to the screws removed in step #7. It also makes it easier to remove and reinstall the side cover.

My scanner glass was not broken, but inside surface had a dirty haze that was effecting my scans and needed cleaning. Thanks, I was ready to buy a new scanner.

Rich Monell - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 1

Letzten 7 Tage: 3

Letzten 30 Tage: 20

Insgesamt: 455