Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 2 : Schritt 1, Bild 2 von 2
    • Use the nylon spudger to remove the rubber pads near the hinge of the screen, then remove the screws under the pads.

    • Use the Phillips #0 to remove four 9mm screws.

    • Use the Phillips #0 to remove seven 6mm screws.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Use the nylon spudger to pry the back casing near the hinges for the screen.

    • Continue to pry along the edge of the back case until the back is ready to be removed.

    • Careful when beginning to remove the case. There is a cable attached between the bottom case and the motherboard that must be properly disconnected.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 2 : Schritt 3, Bild 2 von 2
    • Use the blue plastic opening tool to lift up on the white tab that is holding the cable in place on the motherboard.

    • Now carefully pull the cable out of place and remove the entire back casing.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Remove the five 6mm screws that hold the battery in place using the Phillips #0.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • Use the nylon spudger to pry away the blue/white wire that is positioned near your battery.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Disconnect the battery cable from the motherboard by carefully pulling on the black wire at the point closest to the white tab.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • Remove the battery from your device.

Ziellinie

3 weitere Nutzer:innen haben diese Anleitung absolviert.

Joseph Lintz

Mitglied seit: 09/15/16

915 Reputation

5 Anleitungen geschrieben

Team

USF Tampa, Team 11-5, Blackwell Fall 2016 Mitglied von USF Tampa, Team 11-5, Blackwell Fall 2016

USFT-BLACKWELL-F16S11G5

3 Mitglieder

5 Anleitungen geschrieben

2 Kommentare

Only four 6mm screws retaining battery, middle screw secures by passing through back cover. Otherwise very helpful.

norman.huntbach - Antwort

i followed every step on this guide and when i was finished my laptop wouldn’t turn on

premium destroyers - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 4

Letzte 30 Tage: 20

Insgesamt: 4,071