Ersatzteile

Kein Ersatzteil erforderlich.

Press down and to the  right on the battery lock slide.
  • Press down and to the right on the battery lock slide.

  • Once slid over to the right the battery will pop up and out.

Kommentar hinzufügen

Remove the seven screws from the back side of the laptop using a Philips Head screwdriver size PH1.
  • Remove the seven screws from the back side of the laptop using a Philips Head screwdriver size PH1.

Kommentar hinzufügen

  • Remove the seven screws from the battery compartment using a Philips Head screw driver size 0.

Kommentar hinzufügen

  • Turn the computer around to the front side.

  • Using the spudger tool prop open the key board casing.

Kommentar hinzufügen

  • Carefully lift up the key board.

  • Then gently pull up the connecting wire clip to completely detach the keyboard.

Kommentar hinzufügen

  • At the top right of the laptop there will be an another wire clip holding the keyboard casing.

  • Carefully pull out the wire clip to fully detach the covering.

Kommentar hinzufügen

  • At the top right of the laptop remove the black wire from under the metal tabs using the tweezers.

Kommentar hinzufügen

  • Remove the black wire from the top right corner by gently pulling outward.

Kommentar hinzufügen

  • At the top left of the computer remove the black clip using the spudger.

  • Push the spudger to the right to pop out the clip.

Kommentar hinzufügen

  • Locate at the bottom left of the computer a white clip.

  • Using the spudger prop out the white clip.

Kommentar hinzufügen

  • On the left side of the computer locate the black wire with the clear clip.

  • Gently pull the wire to the right to detach it.

Kommentar hinzufügen

  • At the top corners of the computer, unscrew the 3 screws using a Philips Head screwdriver size 0.

  • Lift up the top half of the computer carefully.

Kommentar hinzufügen

  • Locate the two screws at the bottom corners of the screen.

  • Using the tweezers remove the rubber black covering over the screw.

  • Using a Philips Head screwdriver size 0 remove the two screws.

Kommentar hinzufügen

  • Using the spudger prop off the screen covering.

  • Remove the covering to expose the screen completely.

Kommentar hinzufügen

  • Remove the bottom two screen bearings.

  • Using a Philips 1 screwdriver remove the two screws on each side.

Kommentar hinzufügen

  • Using the tweezers remove the red and white wire from the bottom of the screen.

Kommentar hinzufügen

  • Prop the screen up slightly .

  • Using the tweezers unclip the white wire.

Kommentar hinzufügen

  • While the screen is still propped open remove the black wire from the bottom middle of the screen by pulling gently.

Kommentar hinzufügen

  • Remove the screen from the outer casing carefully.

Kommentar hinzufügen

  • Locate RAM access door on the bottom side of the laptop.

Kommentar hinzufügen

  • Locate the two screws holding down the RAM access door.

  • Unscrew the two screws with a size #1 Phillips screwdriver.

Kommentar hinzufügen

  • Lift up on the RAM cover and remove it to reveal RAM sticks.

Kommentar hinzufügen

  • Gently pull apart the two metal tabs located on both sides of the stick of RAM.

Kommentar hinzufügen

  • Gently lift the RAM stick up and out of its seat.

Kommentar hinzufügen

  • Repeat the previous two steps for the remaining stick of RAM.

Kommentar hinzufügen

  • With the battery and RAM removed, locate the hard drive access panel.

Kommentar hinzufügen

  • Remove two 1.2 mm Philips#01 screws.

Kommentar hinzufügen

  • After the screws are removed, slide the hard drive panel to right to remove it.

Kommentar hinzufügen

  • Identify the three screws holding the hard drives cover in place.

  • Remove each screw using a #0 Philips screwdriver to reveal the hard drive.

  • This particular laptop does not contain a hard drive-- yours will.

Kommentar hinzufügen

  • Locate the storage battery, next to the hard drive.

  • Genlty pop out storage battery with fingers.

Kommentar hinzufügen

  • Locate the Wifi card cover panel, left of the RAM.

  • Using a Philips #1 screwdriver remove the screw holding the panel down.

Kommentar hinzufügen

  • Lift up on the screw side to remove the panel.

Kommentar hinzufügen

  • Remove two 1.2 mm Philips#01 screws.

  • As the screws are removed the Wifi card will pop up.

Kommentar hinzufügen

  • Remove Wifi card by pulling to the left of the laptop.

Kommentar hinzufügen

  • Flip over to the top view

  • Remove five 1.2 mm Philips#00 swrews

Kommentar hinzufügen

  • Using a spudger unclip the casing around all corners and edges.

Kommentar hinzufügen

  • lift up the casing and remove to reveal the speakers.

Kommentar hinzufügen

  • Remove highlighted 1.2 mm Philips #00 screw from right speaker.

Kommentar hinzufügen

  • Using a spudger, remove the highlighted white wire.

Kommentar hinzufügen

  • Using a spudger, remove both additional highlighted wires from the motherboad.

Kommentar hinzufügen

  • Lift up and out each speaker from the base.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Zachary Herrera

Mitglied seit 20.03.2018

485 Reputation

2 Anleitungen geschrieben

Team

UMass Dartmouth, Team S4-G5, Covino Spring 2018 Mitglied von UMass Dartmouth, Team S4-G5, Covino Spring 2018

UMASSD-COVINO-S18S4G5

3 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 2

Letzte 30 Tage: 3

Insgesamt: 36