Einleitung

How to get to the motherboard.

Note: This is one of the more difficult fixes. Make sure to keep track of your screws and everything you remove from the device as you take them out. Not doing so may cause worse problems than faulty speakers.

In order to do this, it would be wise to keep a tray with several compartments and some sticky notes to separate and label screws from specific locations on the device as you remove them.

Ersatzteile

Kein Ersatzteil erforderlich.

Begin by turning the laptop over so that you can see the bottom of the computer.
  • Begin by turning the laptop over so that you can see the bottom of the computer.

Kommentar hinzufügen

Slide the battery release switch to the right while simultaneously lifting up the battery.
  • Slide the battery release switch to the right while simultaneously lifting up the battery.

Kommentar hinzufügen

  • Loosen the 8 Phillips screws around the plate and remove the plate.

Kommentar hinzufügen

  • Remove the 9 Phillips screws from the plate covering the fans.

  • The 3 screws around the lower fan also hold the fan onto the metal plate.

Kommentar hinzufügen

  • Lift the plate and lower fan off the heat sink being careful not to damage the lower fan cable, which is attached to the motherboard.

  • Disconnect the lower fan connector from the motherboard.

  • Remove the metal plate and lower fan.

  • The lower fan will easily separate from the metal plate.

Kommentar hinzufügen

  • Disconnect the upper fan connector from the motherboard.

  • Remove the 4 spring loaded screws holding the heat sink assembly to the motherboard.

  • When reassembling, thread all screws in 1 - 1 1/2 turns then alternately tighten each screw 1 turn - starting top left, then bottom right, then bottom left, then top right, then top left again etc. until the heat sink assembly is firmly seated and all screws are tightened the same amount.

Kommentar hinzufügen

  • Slide the heat sink assembly including the upper fan out by pulling it down and left simultaneously.

  • When reinstalling heat sink, ensure it is thoroughly cleaned and the thermal paste (or pads ) are replaced to ensure proper thermal contact with the devices on the logic board to prevent thermal issues.

Kommentar hinzufügen

  • Begin after removing the battery and fans.

  • Remove the screws from the outer frame of the laptop.

Kommentar hinzufügen

  • Remove screws from the battery area, noting the following:

    • These screws are on oversize clearing holes, but hold other components on the keyboard. You can remove them now, but you'll have parts loose and dropping out if you remove the keyboard, so you may want to wait.

    • Two screws secure the optical drive: one in the battery compartment and one in the RAM compartment.

    • With the screws removed, PUSH out the optical drive thru the opening at the BLUE arrow. You will need to remove the drive in order to have access to 2 more screws at the edge of the frame in the opening of the optical drive attached to the bezel of the keyboard.

Kommentar hinzufügen

  • Remove the 8 screws from the back panel of the laptop.

Kommentar hinzufügen

  • Using a flathead remove the 2 screws on the left-side panel of the laptop.

Kommentar hinzufügen

  • Open the laptop so that both the screen and keyboard are in view.

  • Carefully pry off the frame above the keyboard.

Kommentar hinzufügen

  • To begin disconnecting the monitor, remove the 2 screws.

  • Do not pull monitor off yet.

  • Make sure to keep the screen propped up to reduce the amount of strain on the screws as you take them out.

Kommentar hinzufügen

  • Disconnect the 2 wires connecting the monitor to the rest of the laptop.

  • Note: Do not tug on the wires. Just like wall plugs, you need to disconnect them from the actual point of connection.

Kommentar hinzufügen

  • Remove the screws holding the keyboard to the chassis.

  • Unplug the wire just below the right screw shown and the small white connector to the left of that screw.

Kommentar hinzufügen

  • You can now carefully pry the keyboard off. However, do NOT do so yet. There are still wires connecting the 2 components together.

  • The far end of the Keyboard bezel may still be held by 2 screws that can only be accessed by Removing the CD-ROM out of the way. Mentioned in step 9

Kommentar hinzufügen

  • Disconnect the 3 ribbon cables attached to the motherboard.

  • The wire ribbons are removed by snapping out the small latches on the sides of the connection components. The ribbons should slide out with ease.

  • See images 2 and 3 for a closer look.

Kommentar hinzufügen

  • Remove the screws from the motherboard.

  • There are many different sizes and types of screws here. Make sure you are keeping track of where they all belong.

Kommentar hinzufügen

  • Disconnect the wires, belonging to the speakers, from the motherboard.

Kommentar hinzufügen

  • Remove CD-Rom By simply sliding it out.

Kommentar hinzufügen

  • Pry the frame off the laptop outwards while simultaneously lifting the motherboard out of it.

  • Go slowly on every side instead of focusing on only one corner.

Kommentar hinzufügen

  • You can now carefully remove the entire Motherboard.

  • Note: Unless you plan on replacing it, handle the motherboard with care. This is the heart of your computer. Any damage will cause a system failure.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

8 weitere Nutzer haben diese Anleitung absolviert.

Shantel

Mitglied seit 20.04.2010

470 Reputation

6 Anleitungen geschrieben

Team

Cal Poly, Team 30-37, Garner Spring 2010 Mitglied von Cal Poly, Team 30-37, Garner Spring 2010

CPSU-GARNER-S10S30G37

4 Mitglieder

6 Anleitungen geschrieben

this guid is perfect for a new bee to disassemble a laptop.forget about grammer and bullets points.follow the images it is great

asif nawaz - Antwort

thanks, you really help me

checodel - Antwort

Very helpful guide, thanks a lot.

saturnjg2001 - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 15

Insgesamt: 20,467