Turn off down the computer, and unplug the computer from all external power sources.
  • Turn off down the computer, and unplug the computer from all external power sources.

  • Shut the screen, and lay the computer face-down on a flat, sturdy surface. Orient the computer to match the image.

  • Locate the battery release switch, as indicated in the image. Sliding this switch from right to left will release the battery.

  • Remove the battery.

Kommentar hinzufügen

Remove the two 5mm screws securing the right side of the RAM cover to the computer frame. Lift the right side of the RAM cover to remove. Lift the right side of the RAM cover to remove.
  • Remove the two 5mm screws securing the right side of the RAM cover to the computer frame.

  • Lift the right side of the RAM cover to remove.

Kommentar hinzufügen

The wifi card is connected to the computer with the two antenna lead wires.
  • The wifi card is connected to the computer with the two antenna lead wires.

  • Note where the white AUX wire and the black MAIN wire connect to the wifi card before disconnecting.

Kommentar hinzufügen

Disconnect the antenna leads from the wifi card by lifting the gold ends of the wires off the prongs on the wifi card. The white wire connects to the AUX terminal.
  • Disconnect the antenna leads from the wifi card by lifting the gold ends of the wires off the prongs on the wifi card.

    • The white wire connects to the AUX terminal.

    • The black wire connects to the MAIN terminal.

Kommentar hinzufügen

Remove the two 6.0mm screws securing the wifi card to the computer.
  • Remove the two 6.0mm screws securing the wifi card to the computer.

Kommentar hinzufügen

Remove the wifi card.
  • Remove the wifi card.

Kommentar hinzufügen

Remove the two 11.0mm screws at the corners on either side of the battery compartment.
  • Remove the two 11.0mm screws at the corners on either side of the battery compartment.

  • Remove the three 6.0mm screws.

  • Remove the two 5.0mm screws.

  • Remove the 6.0mm screw in the middle of the battery compartment.

Kommentar hinzufügen

Turn the computer over and open the screen. This provides access to the screen hinges.
  • Turn the computer over and open the screen. This provides access to the screen hinges.

  • The keyboard switch cover is attached to the computer with a series of snaps. With a flathead screwdriver, pry up the switch cover until it pops free.

Kommentar hinzufügen

Be careful not to bend the keyboard switch cover too far when removing it.
  • Be careful not to bend the keyboard switch cover too far when removing it.

Kommentar hinzufügen

Next, remove the keyboard. Push on the keyboard frame above the function keys and slide the keyboard toward the screen.
  • Next, remove the keyboard. Push on the keyboard frame above the function keys and slide the keyboard toward the screen.

Kommentar hinzufügen

Carefully lift the trackpad-side edge of the keyboard to reveal the LED and keyboard cable connectors. Detach the cable connectors from the computer by gripping each cable connector close to the computer contact point and pulling up gently.
  • Carefully lift the trackpad-side edge of the keyboard to reveal the LED and keyboard cable connectors.

  • Detach the cable connectors from the computer by gripping each cable connector close to the computer contact point and pulling up gently.

Kommentar hinzufügen

This step is for replacing the keyboard only. If you are not replacing the keyboard, skip this step.
  • This step is for replacing the keyboard only. If you are not replacing the keyboard, skip this step.

    • Lay the keyboard face down.

    • Remove the four 3.00mm screws that attach the keyboard to the keyboard frame.

Kommentar hinzufügen

This step is for replacing the keyboard only. If you are not replacing the keyboard, skip this step.
  • This step is for replacing the keyboard only. If you are not replacing the keyboard, skip this step.

    • Lift the keyboard off the keyboard frame.

Kommentar hinzufügen

Use the plastic prying tool to disconnect the screen cable from the system board. Use the plastic prying tool to disconnect the screen cable from the system board.
  • Use the plastic prying tool to disconnect the screen cable from the system board.

Kommentar hinzufügen

Remove the four 7.0mm screws securing the screen to the computer. Remove the four 7.0mm screws securing the screen to the computer.
  • Remove the four 7.0mm screws securing the screen to the computer.

Kommentar hinzufügen

Separate the screen from the computer frame by lifting the screen straight up. Disconnect the PCI wires by pulling them free of the computer.
  • Separate the screen from the computer frame by lifting the screen straight up.

  • Disconnect the PCI wires by pulling them free of the computer.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Thanh Nguyen

Mitglied seit 05.10.2010

360 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team 21-34, Regan Fall 2010 Mitglied von Cal Poly, Team 21-34, Regan Fall 2010

CPSU-REGAN-F10S21G34

4 Mitglieder

11 Anleitungen geschrieben

To reinstall the PCI WIRES I'm finding no other way to reattach them except by removing the outer cover AND RE-ATTACHING. . I will finish-up the repair and send you my results

Christopher Rouse - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 8

Insgesamt: 12,391