Zum Hauptinhalt wechseln

Ersatzteile

Keine Ersatzteile angegeben.

  1. Slide the silver release tab up and simultaneously lift the cover up from the left side.
    • Slide the silver release tab up and simultaneously lift the cover up from the left side.

  2. Push the tab from left to right to remove the cover.
    • Push the tab from left to right to remove the cover.

  3. Now lift the battery up and away from the device to remove it.
    • Now lift the battery up and away from the device to remove it.

  4. Remove the four silver screws (T5 x .25 in).
    • Remove the four silver screws (T5 x .25 in).

  5. Remove the single black screw (T5 x .125 in) beneath the HP sticker.
    • Remove the single black screw (T5 x .125 in) beneath the HP sticker.

  6. Next, use your plastic removal tool to separate the gray back from the black center piece. For better results, start the separation at the corner piece.
    • Next, use your plastic removal tool to separate the gray back from the black center piece.

    • For better results, start the separation at the corner piece.

  7. Remove the back case.
    • Remove the back case.

  8. Now that the back cover is removed, remove the small screw (#00 Philips x .17) to the left of the SD card slot
    • Now that the back cover is removed, remove the small screw (#00 Philips x .17) to the left of the SD card slot

  9. Next you will need to unlock and remove the ribbon cable Carefully pull back on both sides of the brown bar using metal tweezers, unlocking the cable and slipping it out of the connector
    • Next you will need to unlock and remove the ribbon cable

    • Carefully pull back on both sides of the brown bar using metal tweezers, unlocking the cable and slipping it out of the connector

    • The bar, connector, and cable are fragile components that can be easily broken

  10. Next you need to remove the wire off the bottom of the mother board The easiest method is to use some metal tweezers and grip the plug close to the connector.
    • Next you need to remove the wire off the bottom of the mother board

    • The easiest method is to use some metal tweezers and grip the plug close to the connector.

    • Make sure all these connections are properly disconnected before separation of the motherboard

  11. Next use your plastic removal tool and separate the silver front case from the black frame.
    • Next use your plastic removal tool and separate the silver front case from the black frame.

  12. Remove the 4 screws along the bottom of the faceplate
    • Remove the 4 screws along the bottom of the faceplate

    • They are #00 Philips head screws

  13. Once removed you can easily separate the keys from the body. Once removed you can easily separate the keys from the body.
    • Once removed you can easily separate the keys from the body.

  14. once the joypad key have been removed use the tweezers to carefully maneuver the wire out of its clip releasing the battery once the joypad key have been removed use the tweezers to carefully maneuver the wire out of its clip releasing the battery
    • once the joypad key have been removed use the tweezers to carefully maneuver the wire out of its clip releasing the battery

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

John Pagliero

Mitglied seit: 27.01.2011

912 Reputation

7 Anleitungen geschrieben

This guide is AWESOME.. Thanks! I have an iPAQ 1945 h1900, but this guide was the exact same for my device. I got as far as the taking the battery out without removing the 5th screw beneath the "warranty void" sticker. My only issue--do you know where to get the replacement battery?

Drew Stafford - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 3

Letzte 30 Tage: 10

Insgesamt: 2,461