Zum Hauptinhalt wechseln

Einleitung

The HTC Vive's focus knob may wear down or crack with use. This guide will show you how to replace the Vive's focus knob.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Slide the HTC panel covering the cables forward, away from the Vive. Gently pull on each of the four connectors to remove the sound and Three-in-One cables. Gently pull on each of the four connectors to remove the sound and Three-in-One cables.
    • Slide the HTC panel covering the cables forward, away from the Vive.

    • Gently pull on each of the four connectors to remove the sound and Three-in-One cables.

  2. Undo the hook and loop tape on the straps.
    • Undo the hook and loop tape on the straps.

    • Slide the ends of the straps through the hinge loops.

  3. Pull the facerest cushion off away from the Vive, separating the hook and loop tape.
    • Pull the facerest cushion off away from the Vive, separating the hook and loop tape.

  4. iPhone Akku Fix Kits

    Nur $29.99

    Buy Now

    iPhone Akku Fix Kits

    Nur $29.99

    Buy Now
  5. Use a T6 Torx Screwdriver to remove  either of the two 12mm hinge screws holding the two hinges in place. Allow the hinge to fall away once the screw is removed.
    • Use a T6 Torx Screwdriver to remove either of the two 12mm hinge screws holding the two hinges in place.

    • Allow the hinge to fall away once the screw is removed.

    • Repeat for the opposite side.

  6. Slide the plastic facerest away from the device. Slide the plastic facerest away from the device. Slide the plastic facerest away from the device.
    • Slide the plastic facerest away from the device.

  7. Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards. There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom). Use a plastic opening tool to gently pry up the left side of the outer sheath.
    • Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards.

    • There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom).

    • Use a plastic opening tool to gently pry up the left side of the outer sheath.

    • If the left sheath is glued down, slide your plastic opening tool along the middle seam to break the bond.

    • Slide the left side of the sheath outwards.

  8. Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue. Using the plastic opening tool, pry the right side of the sheath upwards slightly. Using your hands, slide the right side of the sheath outwards.
    • Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue.

    • Using the plastic opening tool, pry the right side of the sheath upwards slightly.

    • Using your hands, slide the right side of the sheath outwards.

  9. Remove the focus knob by unscrewing one 4mm #00 Philips head screw. Pull the knob outwards from the device.
    • Remove the focus knob by unscrewing one 4mm #00 Philips head screw.

    • Pull the knob outwards from the device.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Caleb Watts

Mitglied seit: 25.09.2017

1.554 Reputation

11 Anleitungen geschrieben

Team

Cal Poly, Team S18-G1, Forte Fall 2017 Mitglied von Cal Poly, Team S18-G1, Forte Fall 2017

CPSU-FORTE-F17S18G1

5 Mitglieder

11 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 24

Insgesamt: 525