Einleitung
The HTC Vive's midframe can crack if the device receives a major drop. This guide will show you how to replace the Vive's midframe.
Was du brauchst
-
-
Pull the hook-and-loop (Velcro) closure at the top of the head strap apart to release the top of the head strap.
-
-
-
Slide the top part of the head strap through its metal loop on the headset to remove it.
-
-
-
Pull the hook-and-loop closure at the right side of the head strap apart to release the right side of the head strap.
-
Slide the right side of the head strap through its metal loop to remove it.
-
-
-
Pull the hook-and-loop closure at the left side of the head strap apart to release the left side of the head strap.
-
Slide the left side of the head strap through its metal loop to remove it.
-
-
-
Slide the head strap along the cable, away from the Vive.
-
When the head strap comes to the end of the cable, gently slide it over the plugs and remove it.
-
-
-
Use a T5 Torx driver to remove the two 12 mm-long screws securing the head strap mounts on either side of the headset.
-
-
-
Slide the facerest straight away from the headset to remove it.
-
-
-
Use tweezers to remove the small stickers over the four screws securing the outer shell.
-
Use a T5 Torx driver to remove the four 3.4 mm-long screws securing the outer shell.
-
-
-
Use the flat end of a spudger to pry up the top edge of the right half of the outer shell, behind the component cover and near the seam in the center, until it is unclipped from the headset.
-
-
-
-
Grasp the right half the outer shell and pull it to the right and toward the front of the headset until you feel the clips on the front of the cover release.
-
If the shell is difficult to remove, try prying along the seam with the flat end of a spudger to release the clips.
-
-
-
Repeat the last three steps for the left side of the outer shell and remove it.
-
-
-
Use tweezers to remove the clear tape over all four of the sensor array cable connectors.
-
-
-
Use the pointed end of a spudger to flip up the small locking flap on one of the sensor array ZIF connectors.
-
Slide the cable straight out of its socket on the motherboard.
-
-
-
Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables.
-
-
-
Use the flat end of a spudger to pry the camera cable connector straight up from its socket on the motherboard.
-
-
-
Use a PH000 driver to remove the five 3.9 mm screws securing the sensor array.
-
-
-
Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.
-
-
In diesem Schritt verwendetes Werkzeug:Phillips #000 Screwdriver$5.49
-
Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.
-
-
-
Lift the sensor array away from the headset to remove it.
-
-
-
Remove the tape covering the interconnect cable socket.
-
Use the point of a spudger to flip up the small locking flap on the cable socket.
-
Slide the interconnect cable straight out of its socket on the motherboard.
-
-
-
Remove the tape covering the left OLED cable socket.
-
Use the point of a spudger to flip up the small locking flap on the cable socket.
-
Slide the left OLED cable straight out of its socket on the motherboard.
-
-
-
Remove the tape covering the right OLED cable socket.
-
Use the point of a spudger to flip up the small locking flap on the cable socket.
-
Slide the right OLED cable straight out of its socket on the motherboard.
-
-
-
Use a pair tweezers to slightly twist the interconnect cable and press it down until the tabs on either side of the cable clear the hole in the motherboard.
-
-
-
Press the non-port-end of the motherboard toward the top of headset while hinging it away from the midframe to free it from the clips securing that end.
-
Slide the motherboard toward the bottom of the headset, over the clips, to remove it.
-
-
-
Grab the tabs on the side of the ribbon cable's connector and pull gently outwards to loosen it.
-
Remove the ribbon cable for the power button by grabbing the cable with tweezers and sliding it outwards horizontally.
-
-
-
Remove the four 4mm #00 Philips screws by the nose rest holding the midframe to the eyepiece assembly.
-
Remove the four 4mm #00 Philips screws on the top of the device, directly across from the four by the nose.
-
-
-
With one hand on the midframe and the other on the eyepiece assembly, pull the two parts away from each other.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.