Einleitung
Hier wird gezeigt, wie du die alten Zündkerzen entfernst, die neuen für den Einbau prüfst und vorbereitest und zum Schluss einbaust.
Was du brauchst
-
-
Die Zündkerzen sind leicht an der linken Seite des Motorrads zu finden.
-
-
-
Ziehe vorsichtig den Kerzenstecker ab. Ziehe dabei nicht nur am Zündkabel, sondern fasse am Kerzenstecker an und ziehe ihn zusammen mit dem Kabel ab.
-
-
-
-
Drehe die Zündkerze mit einem 11/16" Kerzenschlüssel gegen den Uhrzeigersinn heraus.
-
Entferne die Zündkerze vom Zylinder.
-
-
-
Prüfe immer den Elektrodenabstand deiner neuen Zündkerze mit einer Zündkerzenlehre. Er sollte etwa 1 mm betragen (0.04 Zoll).
-
-
-
Setze die neue Zündkerze mit den Fingern ein und ziehe sie mit der Hand fest.
-
Drehe die Zündkerze mit einem Drehmomentschlüssel mit den richtigen Werten fest
Questions.1 with a stage 1,2 or 3 would you agree a wider gap? 2nd question which is simular to first.i do run my motor a little rich.rather rich than lean.my question is with modification on a harley davidson sportster.what do ou recommend.so many choices from om to iridium to platinum.then the gap and also are you a believer in cutting the eledtrode approx half off for max combustion.how much would you recommend cutting and back to og question.the gap.is a larger gap.capable of power increase.since ive tried both i swear i feel a power increase.but is it anticipated or other varibles???you opinion is valued.
-
-
-
Drücke den Kerzenstecker wieder fest auf die neue Zündkerze auf.
I have a Harley Davidson Xr1200x Sportster which I just got. Changed the oil also tranny & filter as I couldn't find last date of service coang of oil. So yesterday I checked the spark plugs they were clean. But the mechanic cleaned them & said the needed gap them as one was too narrow. Mind you I had no issues at all. Gapped them at 0.40 now I'm not getting the same smooth sound or feel as if it's miss firing. I have iridium spark plugs okn my bike should I change them to NGK or get another set of iridium spark plugs.please advise..
A spark plug Gap is to be checked with a wire feeler gauge, not a flat feeler gauge….
Which wires go to which plug
-
Führe diese Arbeit für den vorderen und hinteren Zylinder durch.
Führe diese Arbeit für den vorderen und hinteren Zylinder durch.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
20 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
8 Kommentare
Couldn't have made it any simpler
-awesome
- appreciated
Thank you so much for your posting. I'm 2k miles from my daughter who is teaching herself how to maintain her own bike. You site is immensely helpful and appreciated as much.
Says between 11 and 18 pounds in manuel
Is there a firing order like on a car I'm just trying to make sure I have the rite plug with the rite plug wire
I really appreciate your site…thank you.
Can anyone tell me if a 1999 sporster has a data link connector port . my bike would not start the coil was bad replaced it now no spark at all can anyone help