Repariere deine Sachen Community Store

Havoc Heli IR LED Replacement

Einleitung

Before beginning this repair, you should be familiar with soldering a circuit board. The soldering skills needed aren't very in-depth, but you'll be working very close to some other components.

Was du brauchst

  1. Havoc Heli IR LED Replacement, Havoc Heli IR LED: Schritt 1, Bild 1 von 2 Havoc Heli IR LED Replacement, Havoc Heli IR LED: Schritt 1, Bild 2 von 2

    • Power off the controller before disassembly.

    • Place a small piece of tape over the Light button to prevent it from falling out in later steps.

    • Flip the controller over so the back is facing up.

    Bearbeiten

  2. Havoc Heli IR LED Replacement: Schritt 2, Bild 1 von 3 Havoc Heli IR LED Replacement: Schritt 2, Bild 2 von 3 Havoc Heli IR LED Replacement: Schritt 2, Bild 3 von 3

    • Remove the battery compartment screw with a small Phillips screw driver.

    • Lift off the battery cover.

    • Remove the six AA batteries from the compartment.

    Bearbeiten

  4. Havoc Heli IR LED Replacement: Schritt 3, Bild 1 von 3 Havoc Heli IR LED Replacement: Schritt 3, Bild 2 von 3 Havoc Heli IR LED Replacement: Schritt 3, Bild 3 von 3

    • Remove the remaining four screws with a small Phillips screw driver.

    • Flip the device over so the front is facing up.

    • Remove the front cover and place it to the left side.

    • Make sure to note the locations of the joysticks and other controls in case they fall out of place during this or future steps.

    Bearbeiten

  5. Havoc Heli IR LED Replacement: Schritt 4, Bild 1 von 1

    • Lift up the red IR LED cover to remove it.

    Bearbeiten

  6. Havoc Heli IR LED Replacement: Schritt 5, Bild 1 von 2 Havoc Heli IR LED Replacement: Schritt 5, Bild 2 von 2

    • Use the soldering iron and solder wick to remove the solder from the IR LED you're replacing.

    • Pull the LED out through the top.

    Bearbeiten

  7. Havoc Heli IR LED Replacement: Schritt 6, Bild 1 von 2 Havoc Heli IR LED Replacement: Schritt 6, Bild 2 von 2

    • Insert the new LED into the slot.

    • Make sure that the short lead of the LED is on the right.

    • Use the soldering iron and solder to connect the new LED.

    Bearbeiten
Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Autor:in

mit 2 anderen Mitwirkenden

Michael Kent

Mitglied seit: 03/30/16

128 Reputation

1 Anleitung geschrieben

Auszeichnungen: 4

+1 weitere Auszeichnung

Team

Michigan Tech, Team 1-13, Lauer Fall 2016 Mitglied von Michigan Tech, Team 1-13, Lauer Fall 2016

MTU-LAUER-F16S1G13

1 Mitglied

1 Anleitung geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 5

Letzte 30 Tage: 11

Insgesamt: 526