Einleitung

Is one side of your Hover-1 Horizon unresponsive? This is a guide to show you how to replace the left gyroscope board, the most likely culprit to your problem. This guide requires a Phillips #2 and a Phillips #1 screwdriver.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Remove the six 12mm Phillips #2 screws holding the base plate. Remove the six 12mm Phillips #2 screws holding the base plate.
    • Remove the six 12mm Phillips #2 screws holding the base plate.

  2. Remove the two 11mm Phillips #1 screws that hold the base plate to the body. Remove the two 11mm Phillips #1 screws that hold the base plate to the body.
    • Remove the two 11mm Phillips #1 screws that hold the base plate to the body.

  3. Remove the base plate by lifting it up. The base plate is connected to the body with wires. The wires are long enough to set the base plate to the side. The base plate is connected to the body with wires. The wires are long enough to set the base plate to the side.
    • Remove the base plate by lifting it up.

    • The base plate is connected to the body with wires. The wires are long enough to set the base plate to the side.

  4. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  5. Remove the two connectors on either side of the board by lifting the tab and pulling out. Remove the connector in the middle of the board by squeezing the tab and pulling up. Remove the connector in the middle of the board by squeezing the tab and pulling up.
    • Remove the two connectors on either side of the board by lifting the tab and pulling out.

    • Remove the connector in the middle of the board by squeezing the tab and pulling up.

  6. Remove the four 11mm Phillips #1 screws that hold the cover on. Remove the four 11mm Phillips #1 screws that hold the cover on.
    • Remove the four 11mm Phillips #1 screws that hold the cover on.

  7. Remove the four 11mm Phillips #1 screws that attach the gyroscope board to the mount. Lift the board to reveal the connections on the bottom. Lift the board to reveal the connections on the bottom.
    • Remove the four 11mm Phillips #1 screws that attach the gyroscope board to the mount.

    • Lift the board to reveal the connections on the bottom.

  8. Remove the middle connector by squeezing the top of the tab and pulling up. Remove the middle connector by squeezing the top of the tab and pulling up.
    • Remove the middle connector by squeezing the top of the tab and pulling up.

  9. Remove the four 12mm Phillips #2 screws that hold the motherboard to the base. Pull the motherboard away from the gyroscope by grabbing it with two hands and pulling it to the right . Pull the motherboard away from the gyroscope by grabbing it with two hands and pulling it to the right .
    • Remove the four 12mm Phillips #2 screws that hold the motherboard to the base.

    • Pull the motherboard away from the gyroscope by grabbing it with two hands and pulling it to the right .

  10. Unclip the black connector by squeezing both sides and pulling them apart. Unclip the black connector by squeezing both sides and pulling them apart. Unclip the black connector by squeezing both sides and pulling them apart.
    • Unclip the black connector by squeezing both sides and pulling them apart.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Casey Winans

Mitglied seit: 08.10.2018

306 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team S13-G6, White Fall 2018 Mitglied von Cal Poly, Team S13-G6, White Fall 2018

CPSU-WHITE-F18S13G6

4 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 13

Insgesamt: 211