Einleitung

Are your wheels experiencing resistance while turning? This is a guide to show you how to check and replace the wires that connect the wheel to the motherboard. This guide requires a Phillips #2 and a Phillips #1 screwdriver, and a 6 mm hex key.

  1. Remove the six 12mm Phillips #2 screws holding the base plate.
    • Remove the six 12mm Phillips #2 screws holding the base plate.

    Kommentar hinzufügen

  2. Remove the two 11mm Phillips #1 screws that hold the base plate to the body.
    • Remove the two 11mm Phillips #1 screws that hold the base plate to the body.

    Kommentar hinzufügen

    • Remove the base plate by lifting it up.

    • The base plate is connected to the body with wires. The wires are long enough to set the base plate to the side.

    Kommentar hinzufügen

    • Remove the two connectors on either side of the board by lifting the tab and pulling out.

    • Remove the connector in the middle of the board by squeezing the tab and pulling up.

    Kommentar hinzufügen

    • Remove the four 11mm Phillips #1 screws that hold the cover on.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Remove the four 11mm Phillips #1 screws that attach the gyroscope board to the mount.

    • Lift the board to reveal the connections on the bottom.

    Kommentar hinzufügen

    • Remove the middle connector by squeezing the top of the tab and pulling up.

    Kommentar hinzufügen

    • Remove the four 12mm Phillips #2 screws that hold the motherboard to the base.

    • Pull the motherboard away from the gyroscope by grabbing it with two hands and pulling it to the right .

    Kommentar hinzufügen

    • Unclip the black connector by squeezing both sides and pulling them apart.

    Kommentar hinzufügen

    • Remove the four 30mm Hex #6 screws.

    Kommentar hinzufügen

    • Remove the metal square by lifting it up and setting it to the side.

    Kommentar hinzufügen

    • Check that all the clips are secured properly.

    Kommentar hinzufügen

    • Remove the clip by squeezing the latch that holds the clips together while pulling apart.

    • Check motion of the wheel after the clip is disconnected. If the wheel is still stuck, reconnect the clip and disconnect the next one.

    • Remove the clip by squeezing the tab while pulling the clip apart.

    • Check motion of the wheel after the clip is disconnected. If the wheel is still stuck, reconnect the clip and disconnect the next one.

    Kommentar hinzufügen

    • Disconnect the remaining three clips by pulling them apart.

    • After each clip is disconnected, check to see if the motion of the wheel has improved. If the wheel is still stuck, reconnect the clip and unclip the next one.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Jenny Dyer

Mitglied seit 08.10.2018

217 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team S13-G6, White Fall 2018 Mitglied von Cal Poly, Team S13-G6, White Fall 2018

CPSU-WHITE-F18S13G6

4 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 5

Insgesamt: 38