Zum Hauptinhalt wechseln

Einleitung

If your hoverboard will not turn on, retain a charge, move, or spin properly, use this guide to help replace your Hover-1 Titan gyroscope/motherboard.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Flip the hoverboard so the bottom is facing up. The right side is the side that has the power button. There is also an "R" on the metal plate underneath the battery.
    • Flip the hoverboard so the bottom is facing up.

    • The right side is the side that has the power button. There is also an "R" on the metal plate underneath the battery.

  2. Using a Phillips #1 screwdriver, remove the two 14 mm screws closest to the center of the hoverboard. Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.
    • Using a Phillips #1 screwdriver, remove the two 14 mm screws closest to the center of the hoverboard.

    • Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

    • Using a Phillips #1 screwdriver, remove the two 15 mm screws located closest to the wheel.

  3. Grip the bottom right panel and lift to remove it. Grip the bottom right panel and lift to remove it. Grip the bottom right panel and lift to remove it.
    • Grip the bottom right panel and lift to remove it.

  4. Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart. Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart.
    • Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart.

  5. Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard. Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard. Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.
    • Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.

  6. Unplug the bottom left connector by squeezing it and pulling it away from the board. Unplug the bottom left connector by squeezing it and pulling it away from the board.
    • Unplug the bottom left connector by squeezing it and pulling it away from the board.

  7. Unplug the white wires by squeezing the connector and pulling away from the board. Unplug the white wires by squeezing the connector and pulling away from the board.
    • Unplug the white wires by squeezing the connector and pulling away from the board.

  8. Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board. Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.
    • Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

  9. Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board. Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.
    • Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

  10. Cut the cable tie and unplug the remaining wires.
    • Cut the cable tie and unplug the remaining wires.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Jessica Ouyang

Mitglied seit: 08.10.2018

517 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team S15-G4, White Fall 2018 Mitglied von Cal Poly, Team S15-G4, White Fall 2018

CPSU-WHITE-F18S15G4

4 Mitglieder

8 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 3

Letzte 30 Tage: 7

Insgesamt: 150