Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Remove the mounting screws from the thumb-turn side of the lock assembly using a Phillips screwdriver.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Remove the cylinder assembly from the lock assembly.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Remove the retaining clip from the back of the cylinder assembly using tweezers or pliers.

    • The clip is delicate and can be broken.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Remove the tail from the assembly.

    • Note the direction the slit in the tail is facing so you can place it back into the cylinder the same way in came out.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
    • Remove the spring cover with the cylinder in the upright position using a Flathead screwdriver.

    • The springs are compressed and may jump out at you.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • Remove the springs carefully with tweezers or pliers and set the springs aside as they will need to be put back in during reassembly.

    • Be careful when pulling the springs out of the assembly. If the springs are bent or stretched too much, they will be unusable.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • Remove the top pins using tweezers or pliers.

    • There are two sets of pins, bottom and top, be careful not to mix them. Top pins are flat on both sides. These pins are the top pins and they will be reused for reassembly.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Remove the plug from the cylinder assembly in the upright position so the bottom pins do not fall out.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Remove the bottom pins from the plug. This can be done easily by turning over the plug and dumping them out.

    • There are two sets of pins, bottom and top, be careful not to mix them. Bottom pins have a cone shape on both ends. These pins are the bottom pins and they will be replaced for reassembly.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 1
    • Place the new keys into the plug.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 3 : Schritt 11, Bild 2 von 3 : Schritt 11, Bild 3 von 3
    • Place the bottom pins into the pin holes until the top of the new pin matches the shear line.

    • Pins that are in the correct position will be flush with the shear line. Incorrect pin placement will be above or below the shear line. The red circle displays an incorrect placement as the pin is above the shear line.

Ziellinie

16 weitere Nutzer:innen haben diese Anleitung absolviert.

cmcmilla

Mitglied seit: 09/21/15

367 Reputation

1 Anleitung geschrieben

Team

Colorado Springs, Team 6-4, Mcmichael Fall 2015 Mitglied von Colorado Springs, Team 6-4, Mcmichael Fall 2015

UCCS-MCMICHAEL-F15S6G4

5 Mitglieder

1 Anleitung geschrieben

5 Kommentare

worked according to the instructions

MICHAEL RATWAY - Antwort

Huh?? What do you do after the last instruction?

Laura Stover - Antwort

Follow the instructions in reverse order starting from step 8.

Michelle Cloutier -

Worked exactly as described. Watch those springs! They fly out easily, and are prone to bend when reinstalled.

Robert Mayberry - Antwort

Any new key or do I need Kwikset keys for step #10?

atexit8 - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 4

Letzte 7 Tage: 33

Letzte 30 Tage: 140

Insgesamt: 53,164