Repariere deine Sachen Community Store

Wie man eine kaputte FLIR ONE repariert

Einleitung

Dies ist eine einfache Reparatur. Öffne das Gerät und schließe den Akku wieder an. Keine Teile oder Schrauben werden benötigt. (Für iPhone oder Android)

FLIR repariert keine FLIR ONE 2G! "Sollte das Gerät der Garantie unterliegen, werden wir das Gerät direkt austauschen, da diese nicht repariert werden. ...Die alleinige Option, die dir bleibt, ist es woanders reparieren zu lassen, da wir keine Geräte unterstützen, welche nicht von der Garantie abgedeckt sind. "

Was du brauchst

  1. Wie man eine kaputte FLIR ONE repariert, FLIR ONE öffnen: Schritt 1, Bild 1 von 2 Wie man eine kaputte FLIR ONE repariert, FLIR ONE öffnen: Schritt 1, Bild 2 von 2

    • Öffne das Gerät mit dem Öffnungswerkzeug im Spalt entlang der oberen Kante auf der Rückseite.

    • Fahre damit fort, das Gerät an allen vier Kanten vorsichtig zu öffnen.

    Übersetzen

  2. Wie man eine kaputte FLIR ONE repariert, Die beiden Hälften trennen: Schritt 2, Bild 1 von 1

    • Die zwei Hälften lassen sich sehr einfach trennen und der Akkustecker lässt sich leicht ablösen.

    Übersetzen

  4. Wie man eine kaputte FLIR ONE repariert, OPTIONAL - Akku überprüfen: Schritt 3, Bild 1 von 1

    • OPTIONAL

    • Lege zwei Stücke 0,255 mm eindrähtigen Isolierdraht (Wickeldraht) zum Anschluss. Drücke diese in die beiden Vertiefungen, um eine Verbindung herzustellen.

    • VORSICHT - Jedes Kabel oder jeder Sensor, größer als 0,255 mm beschädigt wahrscheinlich den Anschluss.

    • Benutze ein Multimeter, um die Akkuspannung zu überprüfen. Sie sollte etwa 3,7 V betragen.

    Übersetzen

  5. Wie man eine kaputte FLIR ONE repariert, Akku wieder verbinden: Schritt 4, Bild 1 von 1

    • Verbinde den Akku wieder vorsichtig. Die beiden Hälften des Anschlusses lassen sich leicht zusammendrücken, wenn sie richtig verbunden sind.

    Übersetzen

  6. Wie man eine kaputte FLIR ONE repariert, Wieder zusammenbauen: Schritt 5, Bild 1 von 1

    • Drücke die beiden Hälften der Hülle zusammen. Möglicherweise leuchtet die LED in der Taste auf oder fängt an zu blinken.

    Übersetzen

  7. Wie man eine kaputte FLIR ONE repariert, Fertig: Schritt 6, Bild 1 von 1

    • Lade das Gerät auf. Eine blinkende LED zeigt das Aufladen an, eine durchgehende, dass es fertig ist.

    • Sobald es aufgeladen ist, verbinde das Gerät mit dem Handy und probiere es!

    • Du bekommst möglicherweise die Meldung "Kamera Daten nicht erhalten. Kameradaten konnten nicht gelesen werden. Temperatur, Genauigkeit und MSX Ausrichtung können vermindert sein." Dies ist scheinbar ein Fehler in einigen Versionen der FLIR ONE App.

    Übersetzen
Ziellinie

20 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Lennart

Annika Faelker

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

25 Kommentare

Totally worked for mine! I almost gave up on it after seeing the YouTube video of the guy smashing his with a hammer. In addition I used a little bit of stablilant 22 contact enhancer product. Thanks Frank!

Todd - Antwort

Cool you shared this info with other folks!

Worked for my Android device!

Dmitry G.L. - Antwort

I can easily find a 185mAh battery but not a 350mAh. Not sure if anyone knows why its shrunk?

185 seems to work fine though.

Great guide. Sooooo easy.

georgedavies@hotmail.com - Antwort

I’m just wondering the same thing : why is there only 185 mAh batteries, with the same model number, and no 350 mAh available online

matthieuv -

Same. Just going to go with the 185. If the battery life is too short, I've had luck (with the current completely dead battery) with plugging it into a small usb powerbank.

gim -

I have the Flir One Pro for Android with the same issue. I can’t figure out how to open it. I have an opening tool and there two plastic corners on the top connector face that come out. I can’t figure out how to get it open like you have.

chris - Antwort

Nice guide. I accidentally broke the plastic connector on the mainboard (the pins are still soldered). Anybody know this connector type? Thx!

Peter D. - Antwort

This is great ill try it but are there replacement batteries out there

Wesley Crutchfield - Antwort

Great job, mine stopeed working after 2years, for no reason, I reconnected it and checked it was 4.2v After reconnecting it started up again! :)

P S - Antwort

The Flir One Pro for Android can be opened by removing the two T5 Torx screws, accessible after the rubber corner bumpers are pulled out. Then remove the two Philips screws holding the USB connector backing plate and lift off the plastic cover over the camera (release a couple of plastic clips). The battery connector can be removed by lifting up the edge opposite to the wires. The battery has 3 wires so it may not be easy to find a replacement.

Albert Jeans - Antwort

Thank you. Worked for mine too. I just took it apart and touched the battery connector and it came on. With mine the battery died and it wouldn't charge or come on or anything, I thought it was gone but its working again.

Ryan G - Antwort

I also have the Flir One Pro for Android with the same issue. I ordered the battery from Amazon and followed your instructions. Opened the back with a razor blade. Snapped in the new battery. Nice guide.

jeff w - Antwort

I opened my FlirOne with ease.

But disconnecting the battery was NOT EASY.

The pins slipped out and the connector is still attached to the mainboard.

Reconnecting will be a real pain. I checked the battery in the meantime: 0.0V . So that explains a lot (= dead beyond repair).

Maybe i ‘ll try to find a matching battery as mentioned in previous comments.

Thanks for the walk-through though.

Reijndert from The Netherlands.

Reijndert de Haas - Antwort

This is the only fixing attempt I have found.

FlirOne Pro. Broke off the iPhone connector.

Is there any fixing? Parts available?

I got two plastic end caps to come off. Looks like there are some screws down in the holes. Maybe T6?

Still haven’t got to shop to see what small allen wrench or ‘smaller than T8’ driver I can find.

I don’t mind if I have to solder an extension/charge cord on to make it work.

JerS - Antwort

How can you open those security screws inside? I need to change the usb connector.. I cant find suitable driver anywhere. Is it like torx tr5, which is not available anywhere..?

Veli-Pekka Kuisma - Antwort

this didnt work. still got an orange led even with an other battery or an power supply at the battery port

Serdal piynirci - Antwort

Before repair. If the green charge LED has an “irregular” blinking pattern during charging this may be a sign of the loose battery connection. Once the connection was repaired (pressed in place) on mine the green charging LED flashed once per second and charged normally.

Note: it appears this is not the battery connector but the **Motherboard** side of the connection. Always Be gentle with your Mother —- Board.

dean g - Antwort

When unplugging the battery, the femaile plug ripped off the PC board.

The reason was that in my case, the plug of the battery was secured to the PC board with a foamy tape. I should have pried off the tape with tweezers before unplugging the battery.

conclusion: Without precision soldiering this camera is destined to the land fill.

alter einstein - Antwort

If someone is not up to the job of micro soldering or lacks the tools or equipment to do such tiny soldering work then there are repair services being sold on eBay for this unit which are a fraction of the cost of trying to replace the unit.

n3tel - Antwort

Thanks for the guide!! It would have been hard to figure out how to get case open. Battery checked out at 3.9V on DMM, plugged it back in and it turned back on. Suspecting contact corrosion, or it needed a power cycle at the battery. We’re having a cold winter and I’m finding lots of air leaks with the FLIR.

Dana Miller - Antwort

i got the flir original one the phone lays on the case like a batt pack how do you get that open

matthew still - Antwort

Good guide. I was surprised and pleased at how easy it was to open the device. I thought I had a dead IR camera module on my hands, but it seems like all I needed to do was to re-seat the battery connector.

Scott DiMiceli - Antwort

Hi, after reconnecting the bat the phone doesn't see the FlirOne. I don't see any button as reset, what can be the bug? Hi laszlo

Laci - Antwort

I reseated my connector and my first gen FLIR One came back to life too

Randy Alfresco - Antwort

When unplugging the battery the plastic jack on the board broke off. I don't think it was soldered on too well as I gently pulled on it to unplug it.

ROMzombie - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 8

Letzte 7 Tage: 67

Letzte 30 Tage: 248

Insgesamt: 38,946