Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 2 : Schritt 1, Bild 2 von 2
    • Using your Phillips screwdriver, remove both screws that are keeping your current (broken) drywall hook in place.

    • Make sure you remove both screws evenly, to avoid bending and damaging the screws and the drywall around it.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • After removing both screws, remove the plastic anchor screws from the drywall.

    • It will leave a big hole, but we will fix that!

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • After removing the anchor screws, take your spatula and press it flush with the wall. Remove debris from the drywall to make the wall flat.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 2 : Schritt 4, Bild 2 von 2
    • Take some patching and with your spatula, apply it on and around the holes in order to fill it up to the surface of the wall.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • Select a new location for your new towel hook and, with one of the screws, mark the spot where you'll drill the holes.

    • Use your screwdriver to tap the two new locations, to make it easier to screw the anchors onto the wall.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Take your new anchor screws and start drilling on your marked holes.

    • Keep screwing them into the drywall until they're flush with the wall.

    • Don't drill too far, or else it will damage the drywall and the towel hook will be uneven!

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Line up your new towel hook with the holes where the anchors are located.

    • Take your screws and start screwing them in manually so they stay in place.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • With your screwdriver, continue screwing the screws in until they're flush with the towel hook.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Voila! Your new towel hook is installed!

    • But how about the hole we patched earlier?

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 2 : Schritt 10, Bild 2 von 2
    • Press the sandpaper against the wall and scrub on and around the hole, to level it with the wall.

    • After doing that for a few seconds, your patch should be leveled and your problem, solved!

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Pietro Coso

Mitglied seit: 03/21/20

211 Reputation

1 Anleitung geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 26

Insgesamt: 1,237