Zum Hauptinhalt wechseln

Huawei Mate 10 Pro Ladebuchse austauschen

Was du brauchst

  1. Huawei Mate 10 Pro Ladebuchse austauschen, Rückabdeckung: Schritt 1, Bild 1 von 1
    • Schalte das Smartphone aus.

    • Erwärme einen iOpener und lege ihn etwa zwei Minuten lang auf die Rückseite des Smartphones, um den Kleber unter der Rückabdeckung zu lösen.

    Erm… Simply impossible to open the phone this way…

    I used the iOpener for 2 mins as instructed, I’ve used even an hair drier for 30 secs on max power (could barely touch the phone after) and still with the suction tool I was not able to open the phone.

    It simply doesn’t budge!!!

    Miguel Oliveira - Antwort

    This was much easier than I expected! ;-)

    I put the phone on a hot-water bottle for about 5 minutes. I put the first pick in the side of the phone, not the top as shown in the next section. Then I kept the phone on the hot water bottle through all the following steps so that the battery glue was nice and warm when it came to that section.

    Oliver Moffatt - Antwort

  2. Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 2, Bild 1 von 3 Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 2, Bild 2 von 3 Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 2, Bild 3 von 3
    • Hebe die Rückabdeckung mit einem Saugheber hoch, bis du die Hellebardenklinge eines Halberd-Spudgers einsetzen kannst.

    • Trenne den Kleber unter der Rückabdeckung rundum mit dem Halberd-Spudger auf.

    • Setze Plektren ein, so dass sich der Kleber nicht wieder verbinden kann, während du an anderer Stelle arbeitest.

    Faire attention à ne pas enfoncer trop le cutter/spatule hallebarde. Surtout à l’approche des boutons ON/OFF et volume, la nappe ne passe pas loin et se branche à coté de l’empreinte digitale.

    Bilan, j’ai coupé cette nappe et n’ai plus de bouton volume et on/off.

    Plus qu’à chercher la piece de rechange pendant que le telephone est ouvert ;)

    NeoX - Antwort

    I found it easiest to insert the first pick on the side of the phone, not the top as shown in the pictures. The side is slightly more flexible than the ends because it is longer.

    Oliver Moffatt - Antwort

  3. Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 3, Bild 1 von 2 Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 3, Bild 2 von 2
    • Entferne die Rückabdeckung noch nicht ganz. Das Kabel des Fingerabdrucksensors ist immer noch an der Hauptplatine angeschlossen.

    • Klappe die Rückabdeckung zur Seite.

    • Entferne die Kreuzschlitzschraube #00, mit der die Metallabschirmung befestigt ist, die sich auf dem Verbinder des Fingerabdrucksensorkabels befindet.

    When re-assembling, you can test the phone before putting the covers back on. If you test it before you connect the fingerprint reader then you need to re-start the phone before the fingerprint reader will work.

    Oliver Moffatt - Antwort

  4. Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 4, Bild 1 von 2 Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 4, Bild 2 von 2
    • Entferne mit einer Pinzette die Metallabschirmung, die den Stecker des Fingerabdrucksensors bedeckt.

    • Trenne das Fingerabdrucksensorkabel mit einem Spudger ab.

    • Verwende beim Zusammenbau wo nötig neue Klebestreifen.

  5. Huawei Mate 10 Pro Ladebuchse austauschen, Abschirmungen: Schritt 5, Bild 1 von 3 Huawei Mate 10 Pro Ladebuchse austauschen, Abschirmungen: Schritt 5, Bild 2 von 3 Huawei Mate 10 Pro Ladebuchse austauschen, Abschirmungen: Schritt 5, Bild 3 von 3
    • Entferne die zwölf Kreuzschlitzschrauben #00.

    • Entferne vorsichtig die Abschirmung über der Hauptplatine und der Ladeplatine.

    • Wenn die Abschirmungen nach dem Ausdrehen der Schrauben nicht leicht von selbst herauskommen, dann kannst du sie mit einer Spudgerspitze heraushebeln.

    When re-assembling, you can test the phone before putting the covers back on. However, if you test it before you fit the top inner cover (the one in the middle picture above) the speaker will not work.

    Oliver Moffatt - Antwort

    The top and bottom inner covers both have tiny flanges which you need to insert into slots in the outside edge of the phone before you drop the rest of the cover into place. If you don't put the flanges in first the covers will not fit properly.

    Oliver Moffatt - Antwort

  6. Huawei Mate 10 Pro Ladebuchse austauschen, Ladebuchse: Schritt 6, Bild 1 von 2 Huawei Mate 10 Pro Ladebuchse austauschen, Ladebuchse: Schritt 6, Bild 2 von 2
    • Löse das Flachbandkabel der Ladebuchse mit einem Spudger von der Hauptplatine und der Tochterplatine ab.

  7. Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 7, Bild 1 von 2 Huawei Mate 10 Pro Ladebuchse austauschen: Schritt 7, Bild 2 von 2
    • Entferne die Ladebuchse und das Flachbandkabel behutsam mit einer Pinzette.

    • Die Ladebuchse sitzt sehr eng in ihrer Vertiefung. Wenn sie schwer herauskommt, dann heble sie mit dem flachen Ende eines Halberd-Spudgers heraus.

    Do I need to apply a new sealer / adhesive tape in order to assemble the phone back together? If yes, where can this be purchased for Huawei Mate 10 Pro?

    Megan - Antwort

    If the adhesive on the back cover is damaged too much and/or doesn’t stick any more it is recommended to remove the old adhesive from the back cover and clean off any residue with isopropyl alcohol (>90%). Then use thin double sided adhesive tape and apply new strips of adhesive.

    Tobias Isakeit -

    hi, after this install it will still will water proof ?

    David Tay - Antwort

    Hi David,

    opening the Mate 10 Pro will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally, but will loose its water-protection.

    Dominik Schnabelrauch - Antwort

    Hi there, I completed the battery replacement nicely with all your steps, the phone could turn on and function normally, the only issue after the battery replacement is the phone has no sound and vibration. I have ensure all connectors are back to place securely. Does anyone have any clue of the cause of no sound and no vibration?

    Shawn W - Antwort

    You do not have to remove the charging port for battery replacement, it does not interfere anywhere. I couldn't get the charging socket out at all. Where is the trick?

    Christian - Antwort

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

18 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Dominik Schnabelrauch

Mitglied seit: 11/23/16

201.012 Reputation

682 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.560 Anleitungen geschrieben

2 Kommentare

Great tutorial! It has been a month without being able to charge my phone, and now it charges 2x as fast with my repair.

Bruce Panagopoulos - Antwort

I recommend testing the USB C flex cable assembly before you reassemble the phone. As soon as it’s connected to the upper connector and the battery is plugged in the phone should be charging. Mine was broken from the factory but I went to a great local repair shop and got a new one, the guy said 1 out of 15 is broken from the factory. Great tutorial, successful repair.

Martin Olsson - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 3

Letzte 7 Tage: 15

Letzte 30 Tage: 66

Insgesamt: 15,899