Einleitung

The power supply is what transforms the alternating current electricity from a wall outlet into a lower voltage direct current that is usable by the projector. There are many sensitive electronics in a power supply, and a power surge or other electrical issue can fry capacitors and other delicate components, breaking the power supply and preventing the projector from turning on.

The power supply in this projector has an enclosure which the speaker and main fan are mounted on, and the base of the enclosure with the attached power supply can be removed and replaced.

Place the projector on its back (buttons down) with the lens facing away from you.
  • Place the projector on its back (buttons down) with the lens facing away from you.

  • Remove the two 84mm screws in the upper left and right corners of the projector using the Phillips #2 screwdriver.

  • Remove the remaining three 8.5mm screws using the Phillips #1 screwdriver.

Kommentar hinzufügen

Use the plastic opening tools to push down the clips holding the lamp cover in place, and remove it.
  • Use the plastic opening tools to push down the clips holding the lamp cover in place, and remove it.

  • There is no lamp assembly in the projector used in this guide, yours may appear different.

Kommentar hinzufügen

  • Remove the two 8.5mm rear screws holding the rear case plate to the projector using the Phillips #1 screwdriver.

  • Pull the rear plate straight off and set it aside.

Kommentar hinzufügen

  • Flip the projector over and turn around so that the lens faces you.

  • Twist the gray zoom adjustment ring clockwise and extend the lens all the way out, and then slide the zoom adjustment ring all the way towards the end of the lens as far as it will go.

  • Slide the front case plate towards the loosened zoom adjustment ring, until the top plate of the projector is freed from underneath the lip of the front case plate.

  • The front case plate will not come all the way off due to the zoom adjustment ring obstructing it. It will merely slide forward a bit.

Kommentar hinzufügen

  • Lift away the top case plate and set it aside.

Kommentar hinzufügen

  • Remove the four T10 Torx 8.5 mm screws holding the DLP board in place.

Kommentar hinzufügen

  • Unplug the small ribbon cable attaching the DLP board to the motherboard.

Kommentar hinzufügen

  • Detach the DLP board from where it is connected to the motherboard by a large 100 pin connector.

    • Pry up gently while wiggling from left to right if needed.

  • The ribbon cable on the other side of the board could break if pulled too hard.

Kommentar hinzufügen

  • Remove the 2 remaining T10 Torx 8mm screws securing the motherboard to the power supply.

Kommentar hinzufügen

  • Remove all other cables connected to the motherboard.

    • Remove the Speaker Cable

Kommentar hinzufügen

  • Remove Secondary Fan Cable

Kommentar hinzufügen

  • Flip up the DLP board, leaving it attached to the large ribbon cable.

  • Remove DLP Power Cable.

Kommentar hinzufügen

  • Pry out the DLP support piece by gently wiggling it side to side while applying a steady pull. It will slide out.

Kommentar hinzufügen

  • Remove the two 1/4" screws using the nut driver.

    • The second screw is located behind the right side of the 100 pin connector.

  • Gently pry up the motherboard from the connector on top of the power supply.

Kommentar hinzufügen

  • Disconnect the lamp power supply cables from the top of the lamp housing, by gently pulling the two wires in opposite directions.

Kommentar hinzufügen

  • Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out.

Kommentar hinzufügen

  • Rotate the power supply so that the main fan enclosure faces to the right, with the motherboard mounting pegs on top.

  • Remove the two #2 Phillips 7mm screws on the side of the power supply.

  • Remove two more #2 Phillips 7mm screws on the opposite side of the power supply.

  • Rotate the power supply so the fan faces towards you, and remove a fifth #2 Phillips 7mm screw from just under the foam pad.

Kommentar hinzufügen

  • Use a plastic prying tool to push the white molex connector through the fan enclosure.

Kommentar hinzufügen

  • Flip the power supply over so that the motherboard mounting pegs are on the bottom.

  • Carefully open the power supply, and be mindful of the cable that will be pulled taut that needs to be disconnected.

    • It may be easier to disconnect this cable if you orient the power supply with the speaker down, so you can reach in more easily.

Kommentar hinzufügen

  • The base of the power supply should now be free.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Andrew Kennedy

Mitglied seit 29.01.2013

120 Reputation

6 Anleitungen geschrieben

Team

Cal Poly, Team 20-3, Maness Winter 2013 Mitglied von Cal Poly, Team 20-3, Maness Winter 2013

CPSU-MANESS-W13S20G3

4 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 3

Letzte 30 Tage: 9

Insgesamt: 2,113