Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Place the projector on its back (buttons down) with the lens facing away from you.
-
Remove the two 84mm screws in the upper left and right corners of the projector using the Phillips #2 screwdriver.
-
Remove the remaining three 8.5mm screws using the Phillips #1 screwdriver.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the plastic opening tools to push down the clips holding the lamp cover in place, and remove it.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the two 8.5mm rear screws holding the rear case plate to the projector using the Phillips #1 screwdriver.
-
Pull the rear plate straight off and set it aside.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Flip the projector over and turn around so that the lens faces you.
-
Twist the gray zoom adjustment ring clockwise and extend the lens all the way out, and then slide the zoom adjustment ring all the way towards the end of the lens as far as it will go.
-
Slide the front case plate towards the loosened zoom adjustment ring, until the top plate of the projector is freed from underneath the lip of the front case plate.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Lift away the top case plate and set it aside.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the four T10 Torx 8.5 mm screws holding the DLP board in place.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Unplug the small ribbon cable attaching the DLP board to the motherboard.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Detach the DLP board from where it is connected to the motherboard by a large 100 pin connector.
-
Pry up gently while wiggling from left to right if needed.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the 2 remaining T10 Torx 8mm screws securing the motherboard to the power supply.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove all other cables connected to the motherboard.
-
Remove the Speaker Cable
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Flip up the DLP board, leaving it attached to the large ribbon cable.
-
Remove DLP Power Cable.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Pry out the DLP support piece by gently wiggling it side to side while applying a steady pull. It will slide out.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the two 1/4" screws using the nut driver.
-
Gently pry up the motherboard from the connector on top of the power supply.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Disconnect the lamp power supply cables from the top of the lamp housing, by gently pulling the two wires in opposite directions.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Rotate the power supply so that the main fan enclosure faces to the right, with the motherboard mounting pegs on top.
-
Remove the two #2 Phillips 7mm screws on the side of the power supply.
-
Remove two more #2 Phillips 7mm screws on the opposite side of the power supply.
-
Rotate the power supply so the fan faces towards you, and remove a fifth #2 Phillips 7mm screw from just under the foam pad.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a plastic prying tool to push the white molex connector through the fan enclosure.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Flip the power supply over so that the motherboard mounting pegs are on the bottom.
-
Carefully open the power supply, and be mindful of the cable that will be pulled taut that needs to be disconnected.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
The base of the power supply should now be free.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
3 weitere Nutzer:innen haben diese Anleitung absolviert.