Zum Hauptinhalt wechseln

JBL Charge 3 Hauptplatine austauschen

Was du brauchst

  1. JBL Charge 3 Hauptplatine austauschen, Frontabdeckung: Schritt 1, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen, Frontabdeckung: Schritt 1, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen, Frontabdeckung: Schritt 1, Bild 3 von 3
    • Lege dein Gerät mit der Unterseite nach oben und setze ein Plastiköffnungswerkzeug vertikal in den Schlitz in der Frontabdeckung ein.

    • Ziehe das Werkzeug langsam nach außen und löse die Rasten, mit denen die Abdeckung befestigt ist.

    • Wiederhole dieses Verfahren an allen vier Kanten der Frontabdeckung.

    Sometimes disassemblers forget that the first time they disassembled the item it didn’t want to give up easily: I didn’t like the forces I was having to apply at all, so I switched to two plastic prying tools per “corner” and one in-between them (total 5, you could use plectrums…) before I was happy the the forces were low enough not to break anything.

    Frank Puranik - Antwort

    the front grill is supposed to be first not the back the back has longer while the front has shorter clip

    Water Bass Tester (Water BT) - Antwort

    There are two Phillips head screws to remove before prying the cover off

    jason - Antwort

    Where in south Africa can I buy jbl charge3 port bay replacement

    Donovan Fransman - Antwort

    There appears to be different versions of the Charge 3. If you find it difficult to pry open a second side the two small screws mentioned by Jason will need to be removed but it also indicates that there will be some additional changes to this tear down that I will try to convey in the comments as well.

    john Ramirez - Antwort

    Sadly I damaged the latches on my charge 3. There was more to it than just prying the front cover up. First, there is a small latch on both sides that you need to push down before pulling the front cover towards you that release the clips holding the front cover in place. Pull only slightly forward because… Second, in the front cover there are 6 circular notches connected to the front cover in tue four corners including the middle corners, you need to squeeze the front cover a little bit gently removing the notches so they dont break (like mine did).

    ralphkeneth_gomz - Antwort

    Definitely had to watch about 10 videos and still couldn’t get it to pop out easily.. Took a look at the first picture in the next step and really took note of where the little hole that lets you through to push down the tab is. Once I took a look at that and combined the techniques I’d seen in some of the videos it finally popped off easily. https://www.youtube.com/watch?v=u7i0_nD9... I only watched the first minute of this video but it helped a good bit if anyone else is having trouble.

    Rowan Darko - Antwort

    How do you know if the speakers or one of them is burned or broken.. i notice that one speaker is playing much less hard then the other one.. I wonder now if maybe there is another problem with my device.. Battery problem?

    Bukowski101 - Antwort

  2. JBL Charge 3 Hauptplatine austauschen: Schritt 2, Bild 1 von 1
    • Ziehe die Abdeckung auf beiden Seiten vorsichtig auseinander und entferne sie vom Gehäuse.

    • Im Inneren der Frontabdeckung befinden sich Löcher, die beim Zusammenbau in die entsprechenden Stifte des Lautsprechergehäuses passen müssen

    • Das Entfernen der Frontabdeckung beeinflusst nicht die Abdichtung gegen Feuchtigkeit. Allerdings werden beim weiteren Zerlegen des Lautsprechers wasserdichte Verklebungen und Dichtungen beschädigt. Dein Gerät wird danach wahrscheinlich nicht mehr länger wasserfest sein.

    Include dissembling the plastic cover? cover?

    KanGoon - Antwort

    @KanGoon Yes, on mine it took the removal of 6 (reasonably obvious) screws to remove that. I’ll try to insert a photo when I reassemble…

    Frank Puranik - Antwort

    Very good guide! Pics and descriptions make this easy!

    John G Petko - Antwort

    There is a step missing here. How do you remove the rubber cover that covers the port?

    Phillip Luebke - Antwort

    Gibt es eine Möglichkeit diese wieder wasserdicht zu bekommen?

    Furkan Karakelle - Antwort

    Well, broke off the cover tabs. Have to remove 2 screws first. Might add that to the instructions.🤔

    Spartacus - Antwort

  3. JBL Charge 3 Hauptplatine austauschen, Passivstrahler: Schritt 3, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen, Passivstrahler: Schritt 3, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen, Passivstrahler: Schritt 3, Bild 3 von 3
    • Entferne die beiden 8 mm Kreuzschlitzschrauben #1 von den Laschen.

    • Möglicherweise ist auch nur eine Schraube vorhanden.

    If your Charge 3 doesn’t look like the above. Do not do this step YET. Go directly to Step 7 removal of the battery. By doing the battery first it will tell you which radiator to remove and thus no need to remove both.

    NOTE:

    On a newer version of the Charge 3 this image will be very different. you will not find a screw. You will also notice that there are two tabs that if slightly lifted while rotating the radiator counter clockwise the radiator is easily removed. There is also no foam or breakable seal on the newer Charge 3.

    john Ramirez - Antwort

  4. JBL Charge 3 Hauptplatine austauschen: Schritt 4, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 4, Bild 2 von 2
    • Setze unter beide Laschen ein Plastiköffnungswerkzeug ein.

    Beim Modell 2016 geht es noch einfacher: Da ist es ein Bajonett-Verschluss (und nur 1 Schraube im vorigen Schritt). Man muss die Abdeckung nur ein paar Grad gegen den Uhrzeigersinn drehen und kann sie dann einfach abziehen. Schritt 5 und 6 entfallen.

    Franz - Antwort

    I believe this is unnecessary, just turn the passive radiator counter clockwise and pull outward. I tried to use the pry tool and broke a plastic tab.

    Frank Krantz - Antwort

    Tip— when you get to this part lightly tap the edge of the speaker on a hard surface— like you’re tapping a jar before opening it.

    maxthibodeaux - Antwort

    Muchas gracias a todos, me dieron cada uno la guía perfecta.

    Rafael de la Torre Perez - Antwort

    My charge 3 had less screws but the process was the same. Thanks for the instructions!

    Ryan Parker - Antwort

  5. JBL Charge 3 Hauptplatine austauschen: Schritt 5, Bild 1 von 1
    • Verdrehe den Passivstrahler und ziehe ihn zum Öffnen heraus. Den linken Strahler musst du im Uhrzeigersinn drehen, den rechten gegen den Uhrzeigersinn.

    attention assez dur a enlever, le mien dur à tourner

    Walter Rousseau - Antwort

  6. JBL Charge 3 Hauptplatine austauschen: Schritt 6, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 6, Bild 2 von 2
    • Wiederhole alle Schritte für den Passivstrahler auf der anderen Seite.

    • Zum Ersetzen des Akkus muss nur der rechte Strahler entfernt werden.

    right or left…. depends on how you view the Charge 3 i guess. No need to remove both radiators for a newer Charge 3. You can remove the battery cover first…find out what side the battery wires exit the battery compartment and then remove the radiator associated with that same side.

    john Ramirez - Antwort

    Anybody else have major problems trying to twist the radiator back into position after replacing the battery? I’m having trouble getting the screw holes to line up again on the right radiator.

    Chapman Steamer 1 - Antwort

    To twist back I used saliva so it will slide easier against the rubber

    Jaakob Wolff - Antwort

  7. JBL Charge 3 Hauptplatine austauschen, Lautsprecher: Schritt 7, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen, Lautsprecher: Schritt 7, Bild 2 von 2
    • Entferne die acht 10 mm Kreuzschlitzschrauben #1, mit denen die beiden Lautsprecher befestigt sind.

    Die Frage : Ist ob man irgendwo Ersatz Lautsprecher bekommt ???

    nicowihnaleck - Antwort

    Probier's mal hier, vergleiche aber ganz genau (Seriennummer GG…):

    https://ecommerce.mysav.eu/en/jbl/147-sp...

    VauWeh - Antwort

  8. JBL Charge 3 Hauptplatine austauschen: Schritt 8, Bild 1 von 1
    • Ziehe sorgfältig einen der beiden Lautsprecher heraus. Sei vorsichtig, er ist immer noch an der Hauptplatine angeschlossen.

  9. JBL Charge 3 Hauptplatine austauschen: Schritt 9, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 9, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 9, Bild 3 von 3
    • Im Flachstecker des Lautsprechers ist eine kleine Metallverriegelung. Drücke sie mit einem Schraubendreher hinein und ziehe den Stecker vorsichtig ab.

    Where can l buy those speaker for replacing

    Terrence Terrence - Antwort

    Somebody know where I can buy These speakers ?

    motje - Antwort

    The speakers that is on my charge 3 is soldered on doesn’t have the clips in picture

    travenature - Antwort

  10. JBL Charge 3 Hauptplatine austauschen: Schritt 10, Bild 1 von 1
    • Wiederhole diesen Schritt für den zweiten Stecker.

  11. JBL Charge 3 Hauptplatine austauschen: Schritt 11, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 11, Bild 2 von 2
    • Fasse den Stecker am Kabelbündel, welches die Lautsprecher mit der Hauptplatine verbindet, mit einer Pinzette an. Ziehe den Stecker vorsichtig ab.

  12. JBL Charge 3 Hauptplatine austauschen: Schritt 12, Bild 1 von 1
    • Nachdem der zweite Lautsprecher von der Hauptplatine abgetrennt ist, kannst du ihn und seine Anschlüsse herausziehen.

    where can i buy these speaker,i need to replace the left side speaker because it was already damaged

    geoffrey mustar - Antwort

  13. JBL Charge 3 Hauptplatine austauschen, Akku: Schritt 13, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen, Akku: Schritt 13, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen, Akku: Schritt 13, Bild 3 von 3
    • Entferne die sechs 8 mm Kreuzschlitzschrauben #1 von der äußeren Akkuabdeckung.

    • Löse die äußere Akkuabdeckung vom Lautsprechergehäuse ab

    For the newer Charge 3 - there are two silver screws located on the opposite side of the charging ports ….. looking at the first picture above they would be in close proximity to the lower two red circles. However, they placed in horizontally not vertically. Once you remove these two screws you can lift the rubber off.

    Note: The rubber is hinged on the opposite side of the two removed screws by tabs. Be careful when rotating it off not to break the tabs.

    Once the rubber is removed…. you will be able to see the battery compartment. It has several black screws… one of which is wedged between the charging port rubber and the battery cover. You can gently pry up the rubber away to allow you to get a screw driver in to get the middle screw out.

    The battery compartment is water tight and has a seal. You will want to loosen all screws evenly so as not to tear or damage the rubber seal.

    john Ramirez - Antwort

  14. JBL Charge 3 Hauptplatine austauschen: Schritt 14, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 14, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 14, Bild 3 von 3
    • Entferne die sieben 8 mm Kreuzschlitzschrauben #1 von der inneren Akkuabdeckung.

    • Entferne die innere Akkuabdeckung.

    The newer Charge 3 will have a solid black cover. Once removed the battery can be easily lifted out with your fingers. It is not taped in.

    Gently lift the battery to determine the radiator that needs to be removed. You can identify it by following the battery wiring. There is a small hole at the bottom of the battery compartment that the battery wires go through. The side with the battery wiring hole is the same side as the radiator that needs to be removed.

    john Ramirez - Antwort

  15. JBL Charge 3 Hauptplatine austauschen: Schritt 15, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 15, Bild 2 von 2
    • Ziehe vorsichtig und löse den Stecker am Kabelbündel an der Seite des Lautsprechers ab. Dadurch wird der Akku von der Hauptplatine abgetrennt.

    mon problème d’origine était pas de charge sur secteur, dans mon cas nappe 11 connecteurs déconnectée. Je n’ai pas vu de système de retient pour cette nappe, je lui ai ajouté un petit point de colle, car bouge relativement beaucoup ! problème résolu

    Walter Rousseau - Antwort

  16. JBL Charge 3 Hauptplatine austauschen: Schritt 16, Bild 1 von 1
    • Ziehe den Akku und das Kabel aus dem Akkufach heraus.

    Where can I find (shop) a battery replacement ?

    erik g5 - Antwort

    yo tambien quiero una bateria donde la cosigo?

    henryovidioquispemamani -

    Does anyone know where I can buy a replacement battery?

    Tissaka Senarath - Antwort

    Unbedingt die Isolierung um das Kabel und die Polster an den Ecken der Batterie von der alten an die neue basteln, sonst kann sie im Fach hin und her klappern.

    Jaakob Wolff - Antwort

    Se podria adactar este dispositivo directo a un cargador directo?

    Branlys Lopez Barnada - Antwort

    I already did many things to my charge 3 and one of them was to put two direct cables to the battery to be able to charge it since the usb port was damaged and I could not find a replacement, next I will add 4 more batteries

    Ricky Almonte -

    perdon que te respondi en ingles, yo le puse un cable directo usb a la bateria ya que el puerto usb se daño y no pude encontrar repuestos

    Ricky Almonte -

  17. JBL Charge 3 Hauptplatine austauschen, Anschlüsse: Schritt 17, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen, Anschlüsse: Schritt 17, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen, Anschlüsse: Schritt 17, Bild 3 von 3
    • Entferne vier 8 mm Kreuzschlitzschrauben #1 von der Abdeckung der Anschlüsse.

    • Zwänge ein Plastiköffnungswerkzeug um die Abdeckung und entferne sie.

    and then wiggle it directly (almost radially from the cylinder) out until you see the cables shown in the next step.

    Be careful not to damage the plastic gasket as you pull it out,

    Frank Puranik - Antwort

  18. JBL Charge 3 Hauptplatine austauschen: Schritt 18, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 18, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 18, Bild 3 von 3
    • Entferne die beiden Stecker an den Kabelbündeln der Anschlüsse.

    there’s not much room to get you fingers in. Again I used prying tools to help me get the two connectors off the PCB

    Frank Puranik - Antwort

    How do i get another port bay

    pjimenez98 - Antwort

  19. JBL Charge 3 Hauptplatine austauschen: Schritt 19, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 19, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 19, Bild 3 von 3
    • Entferne die drei 8 mm Kreuzschlitzschrauben #1 von der Anschlussplatine

    • Ziehe die Abdeckung der Anschlüsse von der Anschlussplatine ab

    Be careful not to break the 2 plastic lugs you can see just below (on the photo) the 2 screws at the edges

    Frank Puranik - Antwort

  20. JBL Charge 3 Hauptplatine austauschen: Schritt 20, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 20, Bild 2 von 2
    • Entlöte den USB-, Micro USB- und AUX Anschluss von der Platine.

    Salve, dove posso ordinare la presa usb piccola di ricarica, c’è un sito apposito?

    Robert James Hanrahan - Antwort

  21. JBL Charge 3 Hauptplatine austauschen, Hauptplatine: Schritt 21, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen, Hauptplatine: Schritt 21, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen, Hauptplatine: Schritt 21, Bild 3 von 3
    • Entferne die beiden Kreuzschlitzschrauben #1, mit denen die Hauptplatine seitlich befestigt ist.

  22. JBL Charge 3 Hauptplatine austauschen: Schritt 22, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 22, Bild 2 von 2
    • Ziehe vorsichtig den Kabelstecker von der Hauptplatine ab.

    I lost that cable what to do

    Dynamite Gaming - Antwort

    I lost that cable what to

    Dynamite Gaming - Antwort

  23. JBL Charge 3 Hauptplatine austauschen: Schritt 23, Bild 1 von 2 JBL Charge 3 Hauptplatine austauschen: Schritt 23, Bild 2 von 2
    • Ziehe vorsichtig den goldfarbenen Stecker von der Hauptplatine ab.

    Buenos días, se me despegó el otro extremo del cable del conector dorado y quisiera que me indiquen en qué lugar se vuelve a conectar. Muchas gracias

    Javier Cristanchi - Antwort

  24. JBL Charge 3 Hauptplatine austauschen: Schritt 24, Bild 1 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 24, Bild 2 von 3 JBL Charge 3 Hauptplatine austauschen: Schritt 24, Bild 3 von 3
    • Klappe die Sicherungsbügel an den beiden ZIF Anschlüssen hoch.

    • Ziege die beiden Flachbandkabel vorsichtig mit einer Pinzette heraus.

    Ya mine was glued together :(

    nuotio zz - Antwort

  25. JBL Charge 3 Hauptplatine austauschen: Schritt 25, Bild 1 von 1
    • Schiebe die Hauptplatine aus dem Gehäuse heraus.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

10 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Sunmin Yoon

Mitglied seit: 10/30/18

1.793 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team S13-G1, White Fall 2018 Mitglied von Cal Poly, Team S13-G1, White Fall 2018

CPSU-WHITE-F18S13G1

3 Mitglieder

26 Anleitungen geschrieben

10 Kommentare

Internation version is different. There are no screws for passive radiotors.

Tr0ll05aur0s 3z - Antwort

You have to twist it. I have to managed to get it open because there is no video on youtube (I can’t find any)

Tr0ll05aur0s 3z -

If that even is Charge 3.

Tr0ll05aur0s 3z -

My JBL charge 3 is not charging …please give me idea to fix ..but it’s working perfectly only

nagendra.shriyan - Antwort

My jbl charge are charging but it won't turn on…… i have tried several times to turn it on but it won't turn…… hoping for solutions……

cire_012881 - Antwort

hello mate! did you find any solution?

baran.florin -

MAybe your battery or your power button is dead

Max Mustermann -

Where can I buy the motherboard?

leong065 - Antwort

Not charging or does not turn on, It might be a battery problem, usually these speakers have a battery that starts to loose capacity in about 2 to 3 years, and if you are a frequent user, then it can last even less... If the battery is not capable of storing power, it may be the reason for which you cannot turn it on or charge it.
Hope it helps.

Luisgomes999 - Antwort

hi why my jbl don't want to get full charge?

Joshua Flores - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 5

Letzte 7 Tage: 53

Letzte 30 Tage: 237

Insgesamt: 26,520