JBL Flip 2 Auxiliary Port Replacement

Einleitung

This guide will walk you through from taking apart the device, disconnecting all the cables inside and taking out the I/O board in order to replace the auxiliary port.

Was du brauchst

Schritt 1 JBL Flip 2 Outer Case Disassembly

JBL Flip 2 Auxiliary Port Replacement, JBL Flip 2 Outer Case Disassembly: Schritt 1, Bild 1 von 2

JBL Flip 2 Auxiliary Port Replacement, JBL Flip 2 Outer Case Disassembly: Schritt 1, Bild 2 von 2

Begin by removing the rubber caps on both sides of the JBL Flip 2 by using the black spudger to get in between the creases.
Be very careful when removing the NFC rubber cap. There is a chip that is glued to the inside of the rubber cap. So, peel the rubber cap off slowly and remove the chip on the inside while peeling the rubber cap off.

Bearbeiten

From where i can buy these speakers?

Nitin Z - 27. Sep 2019 Antwort

First thing I did was rip the wire from the NFC chip! Luclily I don't need it as I only ever use my flip with my iPhone.

Ken McMahon - 22. Okt 2022 Antwort

Schritt 2

Remove the eight 7.0 mm Phillips #1 screws on both sides of the JBL Flip 2.

Bearbeiten

Schritt 3

JBL Flip 2 Auxiliary Port Replacement: Schritt 3, Bild 3 von 3

The NFC chip is glued onto the side of the device. Use the black spudger to separate the mic from the surface.
Be careful not to sever the wire connecting the nfc chip to the inside of the device.
Gently slide the NFC chip into the device through the slot that the wire comes from.

Bearbeiten

what if the wire DID disconnect? could s.o. add a detail pic of exactly where the cables connect on the chip?

dfhdrt34f3t - 28. Sep 2017 Antwort

Need the real name of the NFC chip, caus i broked and need to change

Thanks

Daniel Huot - 3. Jan 2018 Antwort

Need the real name of the NFC chip, cause i broked and need to change

Thanks

Daniel Huot - 3. Jan 2018 Antwort

My chip reads WN-3088 20130912

Thomas Blanchard - 21. Mai 2023 Antwort

Schritt 4

Peel the black rubber piece from one end to the other.

Bearbeiten

Schritt 5

JBL Flip 2 Auxiliary Port Replacement: Schritt 5, Bild 3 von 3

Remove the two 7.0 mm Phillips #1 screws.
Carefully detach the silver plastic cover by pulling both ends off.
Pull both ends at the same time with the same amount of force to prevent the cover from breaking.
Separate the silver plastic piece by pulling it off from the middle.

Bearbeiten

Tutto molto interessante.

Ma la cosa più importante è:

Dove acquistare gli altoparlanti ??

terlizzigianfranco75 - 20. Jan 2019 Antwort

Schritt 6

JBL Flip 2 Auxiliary Port Replacement: Schritt 6, Bild 3 von 3

Using a flat-head screwdriver or spudger, pry out the 8 metal nibs on the back side of the speaker.
Repeat the same process for the 4 remaining metal nibs (two on each end).

Bearbeiten

Schritt 7

Expand the metal casing and carefully slide it off the speaker.

Bearbeiten

Schritt 8

Using the driver adapter, first insert the #4 socket into the driver; followed by the #1 Philip's head bit in order to reach the three 13.0 mm screws.

Bearbeiten

Schritt 9

JBL Flip 2 Auxiliary Port Replacement: Schritt 9, Bild 3 von 3

Using the classic spudger, get underneath the black tape strips found on both side of the device.
After lifting a portion of the tape off of the device, gently peel the tape off of the device, making sure to keep it intact.
There is another piece of tape on the side of the device with the control buttons. Lift the tape with the classic spudger and then peel the rest of the tape off.

Bearbeiten

For easier removal warm the tape up with a hair dryer. It tears apart very easily.

hale1730 - 23. Feb 2018 Antwort

Keeping the tape intact is impossible - I replaced it with electrical tape.

Ken McMahon - 22. Okt 2022 Antwort

Schritt 10

JBL Flip 2 Auxiliary Port Replacement: Schritt 10, Bild 3 von 3

Wedge a spudger between the two halves where the tape was to pry the device open.
When working with electronics, it's important to choose a tool that's ESD-safe to avoid accidental damage to the device. The regular black nylon spudger or a plastic opening tool should be used whenever possible.

Bearbeiten

Schritt 11

Use the black spudger to disconnect the speaker cord from it's socket.

Bearbeiten

Schritt 12

Use the black spudger to disconnect the auxiliary wire from its socket.

Bearbeiten

What is the function of auxi. Wire

Debabrata Paul - 25. Apr 2018 Antwort

When you plug in the audio jack it goes to the motherboard, the amplifier and then to the wire directly to the speakers.

Jose Palacios - 15. Mär 2020 Antwort

Schritt 13

Carefully remove the cable connecting the control chip to the motherboard.

Bearbeiten

What's the name of the cable connecting the control chip to the motherboard

Jose Cabello - 2. Jan 2017 Antwort

I want motherboard control chip

moneykandan110 - 24. Aug 2021 Antwort

connecting the control chip kitne ka hai

Niraj Kumar - 18. Mär 2024 Antwort

Schritt 14

Using the black spudger, carefully remove the cord connecting the battery to the motherboard.

Bearbeiten

If you can“t see a connector here , you have an earlier version of Flip2 - the connector is on the backside and requires a different battery - see the comment at the end of the feature

Klaus - 20. Apr 2018 Antwort

Schritt 15

Carefully remove the cable connecting the nfc chip to the motherboard.

Bearbeiten

Schritt 16 Auxiliary Port

JBL Flip 2 Auxiliary Port Replacement, Auxiliary Port: Schritt 16, Bild 1 von 1

Remove the one 7.0 mm Phillips #1 screw that connects the I/O board to the casing.

Bearbeiten

Schritt 17

Remove the cord that connects the I/O board to the motherboard.
Put the motherboard to the side.

Bearbeiten

Schritt 18

With the black spudger, carefully wedge out the I/O board.
Be careful not to damage the I/O board with the black spudger.

Bearbeiten

Aku sudah mencobanya tp kabel yg biru putus karna emang udah ketekuk dr pabrikanya

Ach Fauzi - 14. Feb 2022 Antwort

Schritt 19

JBL Flip 2 Auxiliary Port Replacement: Schritt 19, Bild 3 von 3

Gently pull the I/O board out from the speaker.

Bearbeiten

Schritt 20

Desolder the auxiliary port to remove it from the I/O board..
Check out IFixit's official soldering guide for help with these special projects.
Soldering iron will be very hot.