Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

Ist die Akkulaufzeit der Box geschrumpft? Scheint der Akku nicht zu laden? Eine fehlerhafte Batterie ist möglicherweise die Ursache für diese Symptome. Wenn der Akku schon oft aufgeladen worden ist, hält er weniger Ladung.

  1. Führe das Öffnungswerkzeug in den Spalt zwischen der Abdeckung und dem Gummiboden ein. Achte darauf das die Box so steht, das die Akku-LED's links neben dem An/Aus Knopf  sind (wie auf dem Bild). Heble die Abdeckung ab. Beginne an der Seite, wo nicht die Lautstärkeregler sind. Beim Abnehmen der Abdeckung erzeugen  die sechs Clips (drei entlang jeder Seite des Gummirückens), mit denen die Abdeckung am Lautsprecher befestigt ist, Schnappgeräusche.
    • Führe das Öffnungswerkzeug in den Spalt zwischen der Abdeckung und dem Gummiboden ein. Achte darauf das die Box so steht, das die Akku-LED's links neben dem An/Aus Knopf sind (wie auf dem Bild).

    • Heble die Abdeckung ab. Beginne an der Seite, wo nicht die Lautstärkeregler sind.

    • Beim Abnehmen der Abdeckung erzeugen die sechs Clips (drei entlang jeder Seite des Gummirückens), mit denen die Abdeckung am Lautsprecher befestigt ist, Schnappgeräusche.

    • Ziehe die Abdeckung mit den Daumen ab.

    Important suggested edit to these instructions - make sure to pry off clips/ridges from BOTH sides before attempting removal of the cover.

    I interpreted these instructions as saying you only needed to pry clips from one side - then peel off cover. Doing this broke a clip from the other side. Bummer. I'd like others to avoid that.

    kevmuldoon13 - Antwort

    If you do break a clip - save it. They are relatively easy to glue back into the cover.

    kevmuldoon13 -

    My Flip4 had a single long clip on the non-button side that ran the entire length of the rubber spine. The other side (with play/ vol buttons) had three seperate clips (middle and both sides) as mentioned above.

    takentrashout - Antwort

  2. Entferne die vier 13mm JIS #0 Schrauben, mit denen die Gummiränder an den beiden Seiten befestigt sind. Löse mit dem Öffnungswerkzeug die Clips, die den mittleren Teil des Gummirückens halten. Heble einen Gummirand mit den Daumen weg, bis er sich löst. (Wie auf dem Bild).
    • Entferne die vier 13mm JIS #0 Schrauben, mit denen die Gummiränder an den beiden Seiten befestigt sind.

    • Löse mit dem Öffnungswerkzeug die Clips, die den mittleren Teil des Gummirückens halten.

    • Heble einen Gummirand mit den Daumen weg, bis er sich löst. (Wie auf dem Bild).

    • Das Abnehmen der Rückseite kann etwas Fingerspitzengefühl erfordern.

    • Die Lautsprecher sind starke Magnete. Halte sie von anderen empfindlichen Elektronikgeräten fern.

    Suggested Edit : Be careful when removing the screws that they don't get attracted to the speaker (magnet). They can scratch the speaker.

    kevmuldoon13 - Antwort

    Note : screws don't need to be removed from their “channel” (it’s quite difficult). Just unscrew fully and leave in channel.

    kevmuldoon13 - Antwort

    Note or precaution: Place a piece of cardboard over the speaker or use a plastic/rubber/nonmetalic handled screwdriver when loosening/removing the 13 mm screws. The speaker magnets are so powerful that the end of my metal jewelers phillips screwdriver was pulled into the speaker, tearing the plastic/rubber cone. I destroyed two speakers in the process of replacing the battery. Had to buy the speakers from JBL ($16 each).

    Clark Brown - Antwort

  3. Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits
  4. Entferne die fünf 9mm Phillips #1 Schrauben von der Endkappe gegenüber dem USB-Anschluss. Nimm die Endkappe mit den Händen ab. Nimm die Endkappe mit den Händen ab.
    • Entferne die fünf 9mm Phillips #1 Schrauben von der Endkappe gegenüber dem USB-Anschluss.

    • Nimm die Endkappe mit den Händen ab.

    The end cap has some kind of adhesive on it. I’m a strong guy and couldn't pull it off. Sliding a plastic pry tool around the edge helped break the adhesive and make it removable.

    kevmuldoon13 - Antwort

    You helped me a Lot!! There is som versions of these speakers that you need to Twist It a little bit before remove it but wasnt my case… thank you Very much!!

    Luis Frederico - Antwort

    You have to possible sides, chose the one with an “R“ on it. In my version there are no 5 screws. Just lever the endcap lose to remove it.

    Ste fan - Antwort

  5. Entferne die zwei 11mm Kreuzschlitzschrauben #1 Schrauben am Akkufachdeckel. Ziehe den Akkufachdeckel mit den Händen ab. Ziehe den Akkufachdeckel mit den Händen ab.
    • Entferne die zwei 11mm Kreuzschlitzschrauben #1 Schrauben am Akkufachdeckel.

    • Ziehe den Akkufachdeckel mit den Händen ab.

  6. Entferne mit den Händen den großen weißen Stecker, der die Akkukabel an der Hauptplatine anschließt. Ziehe den Akku mit den Händen heraus. Ziehe den Akku mit den Händen heraus.
    • Entferne mit den Händen den großen weißen Stecker, der die Akkukabel an der Hauptplatine anschließt.

    • Ziehe den Akku mit den Händen heraus.

    In my case there was no way to get the Battery out this way as it was a bit bloated and thus stuck.

    By removing the cap on the other side and removing the Charging Port I was able to push it out with the thick side of my screwdriver.

    I also have a slightly other version of the body where the caps are hold by a rotation/clipping mechanism not by screws

    Richardo Otros - Antwort

    Similar to the other comment - I agree - this step was incredibly difficult. It took me about an hour of gentle prying, wiggling, and forceful pulling to get it out. In the end, VERY cautiously using a pair of broad nosed pliers was what allowed me to pull out it.

    Bloating I'm sure does play a role - but I think the main factor is the foam wrapper around the stock battery. It makes it stick to the battery channel.

    You have to be extremely cautious when doing this step, as you don't want to rupture the battery but need to apply a considerable amount of force to get it out with not much leverage for your hands.

    kevmuldoon13 - Antwort

    As mentioned above, the battery is HARD to remove.

    You also need to be very careful to not tear or puncture the battery, as Lithium Ion can have a violent chemical reaction when it mixes with air (Google “Galaxy Note 7 Explosion” to see what I mean!) WEAR EYE PROTECTION at the very least.

    I don’t recommend removing the other side cover and charge port to push the battery out with a screwdriver. Danger!!

    What worked for me was first I inserted my this screwdriver down one side of the battery.

    This pushes the battery all the way to one side of it’s little compartment.

    Then I sprayed some WD-40 on the side after removing my screw driver.

    Then I switched my screw driver to the other side and repeated with the WD-40 on that side.

    Finally, I clamped the wires in a vise and gently pulled while wiggling the batter back and forth in it’s little compartment.

    Still, it took maybe 7mins of carefully pulling while wiggling to finally get it out.

    The wires were destroyed but who cares. The point of removing the battery is to replace it anyway.

    takentrashout - Antwort

    Mine was really bloated and stuck so I also had to push it out from the other side. You have to disconnect the first connector as you look down the tube from the charging port. Then take out 4 screws from the charging port and pull it out toward the exterior as much as you can (there is still another connector on it). That will give you enough room to snake in a long screw driver beside the ribbon cable and push the battery. Be careful around the ribbon cable!

    Flaviu Ciobanu - Antwort

    At the first try i couldn’t move the battery - totally stuck.

    Next day i bought a can of WD-40. After adding some drops an waiting for a couple of minutes the battery was pushable from behind (remove the charging port). ;-)

    Tammo Meyer - Antwort

    Mine was also bloated i had to take out the charging port, and start pushing it from behind until it got out, you have to be really careful since it is a lithium battery and if you pierce it there is a risk of explosion. Great step by step guide!

    Melvin Ulerio - Antwort

    Same “stuck” problem here too.. WD 40, patience and a Card helped… after ALL, I put some felt around the New battery to prevent vibration noise. Take a look: https://photos.app.goo.gl/BH5wGmBpQXRW7g...

    Luis Frederico - Antwort

    Since the Flip 5 have a 4800mAh cap, can I change the battery capacity of the speaker from the current 3000mAh?

    Randl Manigsaca - Antwort

Abschluss

Folge diesen Anweisungen in umgekehrter Reihenfolge, um die Box wieder zusammenzubauen.

34 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Philip Pang

Mitglied seit: 08.10.2018

701 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team S4-G3, White Fall 2018 Mitglied von Cal Poly, Team S4-G3, White Fall 2018

CPSU-WHITE-F18S4G3

4 Mitglieder

10 Anleitungen geschrieben

Is the battery glued into the socket like the Flip 3?

Kenneth - Antwort

No it isn’t. but the black rubber around it makes it really hard to get out. try to push it from the otherside by removing the charging-port.

Be careful not to pierce the battery

Richardo Otros -

Yes with me the battery was glued

Diter Freeman -

Be careful and don’t do like me: my old battery was bloated, so I had to push from the other side, but when doing so, I ripped the ribbon cable from the power button… now trying to find a replacement cable

jmbarroso -

très bon tutoriel, toute l’opération réussie à un bémol prêt, ma batterie aurait chauffé (?) et demeure inextricable de son logement soit elle a gonflé sous l’effet de la surchauffe, soit la bande noire en caoutchouc des extrémités de la batterie ont fondu.

Philippe - Antwort

Am I correct to assume that the speaker will no longer be water proof after performing this? or would it still be able to keep the water out even after the repair?

valenzonap - Antwort

Step 3 seems to be outdated, apparently in newer models the caps with the membranes can be twisted off, no more screws.

Other than that, thanks for the great tutorial! I too encountered the removal problems with the battery (which was on top of that somewhat bloated).

Philipp Wagner - Antwort

Yep, the new models only have two screws inside the body that connect the caps and the outer shell.

Two other points to consider, the screws are absolute trash so it is VERY easy to strip them out. It’s almost easier to take the speakers out by unscrewing them (no need to disconnect them, just pull them out and to the side) so you can get a straight shot at the screws. The other thing is that the new caps can also be quite hard to twist back on. Rather than break your wrists, the body or the caps by wrenching them on, apply a small amount of lubricant like evaporating silicone to the little clasps inside the cap rings. The caps will twist on easily from there

Ian Gun -

Here is a brand new aftermarket replacement JBL Flip 4 battery. It includes all the tools needed for installation and a 1 year replacement warranty!

JBL Flip 4 Battery

Mike - Antwort

This was an excellent tutorial, but should be amended to note that, if the battery is swollen, you can remove the end cap from the other end, remove the USB port (carefully) , and push the battery out from the other side, instead of trying to pull it out.

Joshua Rector - Antwort

Achtung!

Bei mir war der Accu mit dem Gehäuse verklebt, was ein tausch durch einen neuen unmöglich macht.

Diter Freeman - Antwort

Hola cuando me compra reglar jbl flip 4 battery replacement por favor que necesito que me ayuda muchas gracias

julian cruz - Antwort

Buenas noches, mi FLIP 4 luego de sonar un rato comienza a distorsionar el sonido y se apaga; será la bateria defectuosa?

Freddis Rivas - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 98

Letzten 7 Tage: 543

Letzten 30 Tage: 2,207

Insgesamt: 27,189