Einleitung
Wenn bei deiner Box Probleme beim Laden auftreten oder der USB-Anschluss locker erscheint, sind möglicherweise die elektrischen Anschlüsse für die Stromversorgung beschädigt. Möglicherweise ist ein Austausch des USB-Anschlusses erforderlich. In dieser Anleitung erfährst du, wie du den USB-Anschluss auswechseln kannst.
Was du brauchst
-
-
Führe das Öffnungswerkzeug in den Spalt zwischen der Abdeckung und dem Gummiboden ein. Achte darauf das die Box so steht, das die Akku-LED's links neben dem An/Aus Knopf sind (wie auf dem Bild).
-
Heble die Abdeckung ab. Beginne an der Seite, wo nicht die Lautstärkeregler sind.
-
Heble sehr vorsichtig, damit die Clips nicht beschädigt werden.
-
Ziehe die Abdeckung mit den Daumen ab.
-
-
-
Entferne die vier 13mm JIS #0 Schrauben, mit denen die Gummiränder an den beiden Seiten befestigt sind.
-
Löse mit dem Öffnungswerkzeug die Clips, die den mittleren Teil des Gummirückens halten.
-
Heble einen Gummirand mit den Daumen weg, bis er sich löst. (Wie auf dem Bild).
Note or precaution: Place a piece of cardboard over the speaker or use a plastic/rubber/nonmetalic handled screwdriver when loosening/removing the 13 mm screws. The speaker magnets are so powerful that the end of my metal jewelers phillips screwdriver was pulled into the speaker, tearing the plastic/rubber cone. I destroyed two speakers in the process of replacing the battery. Had to buy the speakers from JBL ($16 each).
I have 2 Flip 4's bought approx. a year apart. The older speaker was exactly as described here. The newer speaker does not have the 5 end screws, instead it has a twist to lock end plate. Make sure the top screws that secured the rubber end are removed, as these will prevent end cap twisting. I used rubber gloves to get a grip and twist end cap counter-clockwise to unlock. I found that if you grip end cap too tight it makes it even harder to twist off. Someone may find a better solution, like prising the tags around circumference, but be warned these look flimsy.
Great guide. Only problem is that the battery on mine was in a neoprene sheath and had swollen. It was a bit of a problem to get out. There didn’t seem to be room to fit something to push it out without damaging wires or the motherboard. At the risk of a fire, I worked it back and forth and pulled with a pair of needle nose pliers. Yes there were sparks and some smoke. I did it outside and knew I was risking the whole thing catching on fire. Luckily it went ok.
Great guide! I have a model with the twist-off caps (not 5 screws) with helpful, though subtle, lock/unlock icons on the plastic. Only other problem was replacing the white neoprene battery retainer cover (2 screws). One screw slipped off my screwdriver and fell into the unit - probably stuck to a speaker magnet now. But it doesn't seem to be affecting the sound. iFixit is the best!!
-
-
-
Entferne die vier 9mm Kreuzschlitzschrauben #1 die den grauen USB-Anschluss befestigen.
-
Löse das graue Gehäuse der USB-Abdeckung mit der Hand ab.
Minor point: the colour of the USB port and casing is whatever colour the speaker is. Mine was red so never had a gray USB port or casing.
-
-
-
Entferne die fünf 9mm Kreuzschlitzschrauben #1 um die Endkappe mit dem JBL-Ausrufezeichen zu entfernen.
-
-
-
-
Ziehe den mit dunkelgrauem Schaum beschichteten Draht aus dem Bereich, in dem er verstaut ist, und schiebe ihn aus dem Weg (Wie auf dem Bild).
-
-
-
Löse den weißen Stecker, der an der kleinen Platine des grauen Micro-USB-Gehäuses befestigt ist (Wie auf dem Bild), mit der ESD sicheren stumpfen Pinzette.
-
Ziehe den Stecker durch den Spalt in der großen Leiterplatte, damit du an den nächsten Stecker hinter ihm gelangen kannst.
JBL has upped their “security” I see. On mine, this plug is glued in place and the ribbon cable nearby is completely covered in tape so I can’t unhook it.
-
-
-
Hake den anderen kleineren weißen Stecker hinter dem vorherigen Stecker von der gleichen Leiterplatte mit der Pinzette aus.
-
-
-
Löse den kleinen weißen Stecker, der an der Hauptplatine angebracht ist, die den USB-Anschluss am Lautsprecher hält (Wie auf dem Bild).
-
Entferne die USB-Anschlusskomponente aus dem Lautsprecher.
-
-
-
Entferne die drei 9mm Kreuzschlitzschrauben #1, mit denen die beiden kleinen Leiterplatten an der USB-Anschlusskomponente befestigt sind.
-
Heble die obere kleine Platine mit dem Öffnungswerkzeug ab (Wie auf dem Bild).
-
-
-
Ziehe den schwarzen Klebestreifen auf der Unterseite des Bauteils mit der Pinzette ab und entferne die Kabel darunter.
-
Entferne die erste kleine Platine und die angeschlossenen Drähte.
-
-
-
Ziehe die zweite Platine mit den Händen heraus und entferne sie.
Well presented. Needed. Wire pin descriptions. Thanks
https://www.google.com/url?sa=i&url=http...
Is this what you need ?
-
Folge den Anweisungen in umgekehrter Reihenfolge, um die Box wieder zusammenzubauen.
Folge den Anweisungen in umgekehrter Reihenfolge, um die Box wieder zusammenzubauen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
27 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
11 Kommentare
Hi, I need to replace this circuit board where the charging port mounts.
While trying to remove damaged micro usb port, I damaged the tiny wires from the circuit board.
I tried to find this online but no luck so far.
Do you know the code for this PCB?
Thank you,
hi, where can i buy new circuit board for micro usb charging port?
please i need 1… thank you.
I have a question on the small circuit board (charge port), one of the female port on it is for power (+5v), but what is another one? Is it D+, D- ?
P.S. I’ve measure that port with micro usb connected to power source, turns out there has no voltage measured, but the bigger one does has 5v measured.
Thanks!
https://www.ebay.com/itm/184156589848
Just ordered one of these. Told it’ll be delivered by August 1st.
Would be so great if you could tell us where we could obtain a replacement USB port that INCLUDES the little circuit board. All replacement parts I have found are the port itself and not the port including the little circuit board and plugs.
Hi I discovered water on the inside of the on button rubber layer how do I access it?
Thanks. Brought this speaker back to life. Reconnecting the wires was a little bit of a challenge but got it done in the end.
Hello, great guide thanks! Although I am not quite sure what to buy as a connector. I found two different part available the TL and GG on Aliexpress for instance, does anyone know the difference? Does it matter?
Important suggested edit to these instructions - make sure to pry off clips/ridges from BOTH sides before attempting removal of the cover.
I interpreted these instructions as saying you only needed to pry clips from one side - then peel off cover. Doing this broke a clip from the other side. Bummer. I'd like others to avoid that.
k9612 - Antwort
If you do break a clip - save it. They are relatively easy to glue back into the cover.
k9612 -
My Flip4 had a single long clip on the non-button side that ran the entire length of the rubber spine. The other side (with play/ vol buttons) had three seperate clips (middle and both sides) as mentioned above.
takentrashout - Antwort
What if my speaker battery dies very fast and makes weird crackling noise, is it counted as faulty battery?
Jayden Koh - Antwort
Yes. I first thought one of the drivers was defective.
Paul Sommer -
What was the fix in the end ?
Jack Mulcahy -
I used the flared edge of a metal measuring spoon handle since I didn’t have an opening tool. Worked great! Replacement battery from iFixit is on order. Thanks for the guide!
Greg - Antwort
My battery was glued. Tried it anyway to remove. Battery exploded!!!!
Don't go on if the battery is glued.
darthvader007 - Antwort