Einleitung
Der Bildschirm des Kindle 4 war kaputt. Dies konnte man dies von vorn nicht sehen, aber die Hälfte des Bildschirms war eingefroren und funktionierte nicht mehr. Wir bestellten einen neuen Bildschirm bei: aliexpress
Was du brauchst
-
-
Entferne die Rückseite des Kindle.
-
Beginne mit dem Öffnen der Rückseite an den Seiten. Drücke ein Messer oder eine Pinzette tief in die Mitte der Abdeckung und drehe dein Werkzeug um die verklebte Rückseite zu lösen. Tue dies nicht neben den seitlichen Buttons, weil du sonst die Kabel der Buttons durchtrennen könntest.
-
-
-
Ziehe die schwarze Zuglasche am Akkustecker hoch. Ziehe dann das Kabel vorsichtig aus dem Anschluss heraus.
-
-
-
Jetzt wo die Rückseite des Gerätes entfernt ist, kannst du das Displaykabel abslösen. (Wie in diesem Video von Minute 3:14 bis 3:21 zu sehen.) Folge auch hier dem Video nicht weiter, da wir dies zum Austausch des Displays nicht brauchen.
-
-
-
-
Entferne den vorderen Rahmen des Displays, wie in diesem Video von Minute 4:11 bis 4:48 zu sehen.
-
Folge auch hier dem Video nicht weiter, da wir dies zum Austausch des Displays nicht brauchen.
-
-
-
Beginne am besten an den Seiten und breche das Display Stück für Stück mithilfe einer Pinzette heraus. Der Klebstoff lässt sich leichter lösen, wenn er vorher mit Hilfe eines Föhns erwärmt wurde.
-
-
-
Dies ist der langwierigste Schritt. Entferne die Reste des Klebstoffes und kleine Glassplitter von der Einfassung des Displays. Der Klebstoff muss nicht vollständig entfernt werden, aber die Glassplitter müssen alle entfernt sein.
-
Du kannst den Kleber mit einem Messer von der Oberfläche abschaben. Eine Rasierklinge funktioniert am besten, aber ein normales Messer tut es auch. Du kannst auch Klebstofflöser benutzen.
Steps 5 & 6 are a pain in the butt, yes. It took me several hours to remove all the glass, but everything else was easy and I managed to change the screen without problems :)
-
-
-
Lege das neue Display an seinen Platz.
-
Stelle sicher, dass die Verbinder durch die Einfassung durchgesteckt ist.
-
Verbinde den Stecker mit der Hauptplantine.
-
Teste das Gerät in dem du es anschaltest.
-
Diese Anleitung soll dir helfen das Gerät auseinander zu bauen, den alten Bildschirm auszubauen, gegen einen neuen zu ersetzen und das Gerät danach wieder zusammen zu setzen.
Diese Anleitung soll dir helfen das Gerät auseinander zu bauen, den alten Bildschirm auszubauen, gegen einen neuen zu ersetzen und das Gerät danach wieder zusammen zu setzen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
16 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
17 Kommentare
Mine was around €20 incl shipping: https://nl.aliexpress.com/item/LCD-Displ...
having a really hard time with breaking the screen, any advice beyond what you've posted? what tools do you recommend?
I just used a kitchen knife and a blow dryer. It is definitely the most time consuming part. Good luck!
I've bought ED060SCN LF instead of ED060SCF LF will it work? it is for kindle 5 but seller wrote it is good for Kindle 4 too... might be a good idea to uplug old screen and plug new in just for powering up before start removing the old imho, I will check..
I have no idea, I guess it its worth a try!
Followed the instructions and everything went ok. Removing the screen was very hard and I advise people doing it to take precautions with the glass as it will most likely spray all over. What I did what to cover the screen in transparent tape, so that the glass wouldn’t jump all over. I also wore gloves and protective eye gear.
Hi. I have cleaned all the glue from the bezel. I haven't ordered a screen yet so before I order it I just want to know if the new screen comes with glue or how do you put it on.
Make sure you have a completely flat area, any bits of glass left will create a pivot point under the new glass. Buy thin double sided tape, 25mm width is good and apply to the back up f the chassis. Obviously check your replacement screen works before applying the adhesive.
Hi, I didn't use any glue or tape and it still works perfectly after one year and a half ;-)
Thanks Francis - just completed my replacement. All worked out well!
the only issue that remains is the quality of the image. It seems like the replacement screen is not of the best quality and so there are ghost images left once in a while. It was fun though doing the repair - for sure the worst thing is removing the screen. A pain in @#$%!
Raul
My advice would be to remove everything with the possible exception of the battery, as you will likely destroy it in the process, before removing the screen. If you're replacing the battery as well then obviously remove this too. Dont try to peel off the page turn ribbons as you will likely damage them.
Cleaning the glass fragments and glue is best done with “nitro" thinners ot “acetone" however “acetone WILL MELT the plastic if you get it on it therefore “nitro" is better or 90 -100% alcohol at a push.
Stick the screen back on with the thinnest twin stick you can find.
Works well, but breaking the screen is awkward and time consuming. Price of a new screen is around 20 Euros at aliexpress, and it takes about 1 hr to do the whole replacement. To put everything back in place I used double-sided tape. Easy to use but you need to be a bit more meticulous in removing the old glue.
Steps 5 & 6 are a pain in the butt, yes. It took me several hours to remove all the glass, but everything else was easy and I managed to change the screen without problems :)
Do not remove back cover before Step 4! You might break clips! Start with front cover and you will be able to safely free them.
Viktar Simanenka - Antwort