Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

  1. Using a spudger, gently pry off the aluminum drip ring. Using a spudger, gently pry off the aluminum drip ring.
    • Using a spudger, gently pry off the aluminum drip ring.

  2. Using a 4 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.
    • Using a 4 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.

  3. Using a spudger, pry the planetary gear cover from the mixer shaft. Using a spudger, pry the planetary gear cover from the mixer shaft.
    • Using a spudger, pry the planetary gear cover from the mixer shaft.

  4. Using a flathead screwdriver, remove the five 28 mm front motor housing screws.
    • Using a flathead screwdriver, remove the five 28 mm front motor housing screws.

    • Using the same flathead screwdriver, remove the two 28 mm locking screws.

    • One of the locking screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  5. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  6. Turn your device around. Using the same flathead screwdriver, remove the two 28 mm rear locking screws.
    • Turn your device around. Using the same flathead screwdriver, remove the two 28 mm rear locking screws.

    • One of the rear motor housing screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  7. Using a Phillips #2 screwdriver, remove the 10 mm screw from top of back cover. The rear cover is now completely free from the mixer.
    • Using a Phillips #2 screwdriver, remove the 10 mm screw from top of back cover.

    • The rear cover is now completely free from the mixer.

  8. Carefully pull the power cord from the notch in back of the mixer. The motor housing cover is now completely free from the base of the mixer.
    • Carefully pull the power cord from the notch in back of the mixer.

    • The motor housing cover is now completely free from the base of the mixer.

  9. Lift the motor housing cover from the mixer base.
    • Lift the motor housing cover from the mixer base.

    • Be sure to place the cover upside-down to prevent grease from leaking out.

  10. Use a butter knife or putty knife to remove grease from around the gasket. Place grease in motor housing cover.
    • Use a butter knife or putty knife to remove grease from around the gasket.

    • Place grease in motor housing cover.

  11. Lift the gasket up with your hands or a spuger and remove it.
    • Lift the gasket up with your hands or a spuger and remove it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

Joey Gavin

Mitglied seit: 13.10.2014

191 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 14-28, Maness Fall 2014 Mitglied von Cal Poly, Team 14-28, Maness Fall 2014

CPSU-MANESS-F14S14G28

4 Mitglieder

12 Anleitungen geschrieben

I got all the way to the last step of replacing the pin when i notice the mixer seemed to lock there in place and not move. What did i do wrong?

Dawn dawn6463@yahoo.com

Dawn Bennett - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 17

Letzten 7 Tage: 18

Letzten 30 Tage: 121

Insgesamt: 3,530