Zum Hauptinhalt wechseln

Einleitung

Hier wird der Austausch der Hauptplatine gezeigt.

  1. Wir empfehlen die Mikrowelle vor dem Gebrauch zu reinigen, da sonst Essensreste oder Ähnliches am iOpener hängenbleiben können. Lege den iOpener in die Mitte der Mikrowelle.
    • Wir empfehlen die Mikrowelle vor dem Gebrauch zu reinigen, da sonst Essensreste oder Ähnliches am iOpener hängenbleiben können.

    • Lege den iOpener in die Mitte der Mikrowelle.

    • Für sich drehende Mikrowellen: Stelle sicher, dass der Teller sich drehen kann. Wenn der iOpener hängenbleibt kann er sich überhitzen und sogar Feuer fangen.

    which temperature must be used for heating? Thx

    fbarletta - Antwort

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - Antwort

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - Antwort

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - Antwort

    Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

    Fletcher Carpenter - Antwort

    Video seems to have been removed from YouTube.

    Rex Burrus -

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - Antwort

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - Antwort

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - Antwort

    Hi, the microware have multiple power 1 to 9, what must be used ?

    Regards,

    Cedric

    Cedric VINCENT - Antwort

    My microwave just died, can i heat it with boiled water?

    Alex COLOMBANI - Antwort

    Taping as shown is impractical when using hair dryer method—tape simply comes off in the heat and gets in way of getting out the shards on the sides. If the thing wasn’t shattered, then taping unnecessary.

    B. A. Computer Services - Antwort

    I used the wheat bag in a sensor microwave heating up to 65-70 deg C (155 def F).

    ian cheong - Antwort

    Get yourself a cherry pit bean bag the size of your iPad. Heat it, put the iPad on it for 3 to 5 minutes or so, reheat the cherry pit bean bag, again put your iPad on it. Then heat the iOpener and start working. The cherry pit bean bag will have to be reheated several times, but it will soften the adhesive so you have less problems with the iOpener

    Tim Feyaerts - Antwort

    The “Galaxy S8 Replacement Battery” that you are selling with the kit is the wrong battery, the one that you are selling is a 3000mAh (which is the wrong amperage) as the OEM Samsung Galaxy S8 battery is “Model #: EB-BG892ABA / 4000mAh / Normal Voltage: 3.85V / Charge Voltage: 4.4V / A/S: 1588-3366 4000mAh 15.0Wh

    stevengenat - Antwort

  2. Erhitze den iOpener für dreißig Sekunden.
    • Erhitze den iOpener für dreißig Sekunden.

    • Im Verlauf der Reparatur kühlt sich der iOpener wieder ab. Erhitze ihn dann noch einmal für dreißig Sekunden.

    • Achte darauf, den iOpener während der Reparatur nicht zu überhitzen. Eine Überhitzung bringt den iOpener möglicherweise zum Platzen.

    • Berühre niemals den iOpener, falls er aufgeschwollen aussieht.

    • Falls der iOpener in der Mitte immer noch zu heiß ist, um ihn anzufassen, dann benutze ihn weiter, bis er ein wenig herunter gekühlt ist, bevor du ihn erneut erhitzt. Ein ordnungsgemäß erhitzter iOpener sollte für bis zu 10 Minuten warm bleiben.

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - Antwort

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - Antwort

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - Antwort

    I don't own a microwave.

    mdanihy - Antwort

    Its again waterproof when you change iphone 7 battery?

    Jon - Antwort

    I don't have a microwave???

    Joe Blow - Antwort

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - Antwort

    can i use just ordinary microwave???

    juneseok kwon - Antwort

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - Antwort

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - Antwort

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - Antwort

    All phones/devices differ it’s unrealistic and unsafe to put a exact time/temperature needed to soften the adhesive. It’s really quite simple you warm the device evenly and in a controlled manner just enough to enable pry tools and picks to begin separating. Best tool in my opinion but again this is because I have experience is a hot plate and heat gun both of which are used at nearly the lowest settings and I can handle flat palming the plate for almost 10 seconds I leave the device to conduct heat until approx it’s about 110 at most 120 ish this will be plenty to soften all the adhesive if any problem areas I use heat gun while prying. Again you need go slowly and learn with a throw away phone

    Greg Latta -

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - Antwort

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - Antwort

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - Antwort

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

    K

    Karl Marble - Antwort

    I can’t recommend the microwave. If the the iOpener becomes too hot, it bursts. Better put the opener in cooking water. Dry it and use it. Instead of an iOpener you can use hot/cool packs as well.

    Bernhard Keim - Antwort

    Trust the directions! I forgot and left it in the Microwave too long and after 1 minute I had Mt Vesuvius - the iOpener burst and spewed the goodies out. The problem is, the Digitizer can be damaged by a hot air gun, so I had to tough out and remove the glue the hard way. I made it … with lots of patience! Tough lesson.

    Larry Bennett - Antwort

    I also used a hairdryer. I used it on the low setting and I cut a piece of carboard to protect the rest of the screen. The iFixit tool and method is vert tedious and very time consuming in comparison. With the hairdryer method you can literally have the display apart in a few minutes. Using your other hand nearby the area you are heating it should be very hot but not enough to burn your hand. You only have to heat metal part of case near glass edge. If you have a cellular model then you need to be very careful because the black antenna area is plastic. So less heat and work your way up in adding heat just enough to separate around the area but not so much you melt the plastic!

    Fixrights - Antwort

    iOpener was the worst part of the kit. Followed directions for :30 in microwave and took 4 trips to the microwave to loosen adhesive on left side of home button. I thought I was figuring it out and it was working well… even set a timer to wait 10 minutes between heating it up. Was on the right side and was on my 12th heat up when it exploded in the microwave. My only tip is that if you set it clear side up, as soon as you see any bubbles or boiling in the liquid, STOP! If you put a pot holder over the iOpener and press slightly to make good surface contact, that seemed to help. I finished heating with a “Corn Sack” that held heat better than the provided iOpener.

    digital_only - Antwort

  3. Halte den iOpener an einem der flachen Enden und vermeide die heiße Mitte, während du ihn aus der Mikrowelle nimmst.
    • Halte den iOpener an einem der flachen Enden und vermeide die heiße Mitte, während du ihn aus der Mikrowelle nimmst.

    • Der Beutel wird sehr heiß, sei vorsichtig beim Gebrauch. Lege dir am besten einen Topflappen bereit.

    Will a hair dryer work for heating the glass?

    Me berg - Antwort

    Can you use an oven instead?

    Rafael -

    Yes, as does a heat gun.

    anonymous 4602 - Antwort

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - Antwort

  4. Wende den erwärmten iOpener etwa zwei Minuten lang auf die Kante des Smartphones an.
    • Wende den erwärmten iOpener etwa zwei Minuten lang auf die Kante des Smartphones an.

  5. Wenn die Rückscheibe heiß genug ist, dann setze einen Saugnapf in die Ecke des Smartphones auf. Hebe ihn hoch und setze einen Hellebardenspudger oder ein Plektrum unter die Glasscheibe. Schiebe den Spudger rings um den Rand des Smartphones, um den Kleber zu aufzutrennen. Setze gleich danach ein Plektrum oder ein anderes Werkzeug (Plastikkarte) ein, damit der getrennte Klebstoff sich nicht gleich wieder verbindet.
    • Wenn die Rückscheibe heiß genug ist, dann setze einen Saugnapf in die Ecke des Smartphones auf. Hebe ihn hoch und setze einen Hellebardenspudger oder ein Plektrum unter die Glasscheibe.

    • Schiebe den Spudger rings um den Rand des Smartphones, um den Kleber zu aufzutrennen.

    • Setze gleich danach ein Plektrum oder ein anderes Werkzeug (Plastikkarte) ein, damit der getrennte Klebstoff sich nicht gleich wieder verbindet.

  6. Entferne die elf Kreuzschlitzschrauben #000 an den rot markierten Stellen. Entferne die elf Kreuzschlitzschrauben #000 an den rot markierten Stellen.
    • Entferne die elf Kreuzschlitzschrauben #000 an den rot markierten Stellen.

  7. Nachdem die Schrauben entfernt sind, kannst du die Teile des unteren Rahmens herauslösen, danach den oberen Mittelrahmen. Beide Komponenten können mit etwas Hebeln entfernt werden. Nachdem die Schrauben entfernt sind, kannst du die Teile des unteren Rahmens herauslösen, danach den oberen Mittelrahmen. Beide Komponenten können mit etwas Hebeln entfernt werden.
    • Nachdem die Schrauben entfernt sind, kannst du die Teile des unteren Rahmens herauslösen, danach den oberen Mittelrahmen. Beide Komponenten können mit etwas Hebeln entfernt werden.

  8. Der Ausbau des Akkus beginnt, indem du sehr vorsichtig das Flachbandkabel der Stromversorgung mit einem Spudger oder einer Plastikkarte ablöst.
    • Der Ausbau des Akkus beginnt, indem du sehr vorsichtig das Flachbandkabel der Stromversorgung mit einem Spudger oder einer Plastikkarte ablöst.

    This step is unnecessary IMHO. I’m changing one of the cameras right now and I was able to easily remove the motherboard without touching the battery.

    LAR - Antwort

  9. Ziehe fest an der blauen Lasche. Achte darauf, dass du den Akku beim Ablösen aus der Klebeverbindung nicht verbiegst. Benutze kein Messer, du darfst den Akku keinesfalls verletzen. Benutze kein Messer, du darfst den Akku keinesfalls verletzen.
    • Ziehe fest an der blauen Lasche. Achte darauf, dass du den Akku beim Ablösen aus der Klebeverbindung nicht verbiegst.

    • Benutze kein Messer, du darfst den Akku keinesfalls verletzen.

    dont bend the battery cause mine caught on fire haha

    Bryan Vicente - Antwort

  10. Finde die Öffnung der Lösemechanik für den SIM Einschub an der rechten Seitenkante. Drücke ein geeignetes dünnes Werkzeug, z.B. eine aufgebogene Büroklammer, in die Öffnung und ziehe den SIM Einschub heraus.
    • Finde die Öffnung der Lösemechanik für den SIM Einschub an der rechten Seitenkante.

    • Drücke ein geeignetes dünnes Werkzeug, z.B. eine aufgebogene Büroklammer, in die Öffnung und ziehe den SIM Einschub heraus.

  11. Löse vorsichtig die beiden Stecker unten am Telefon. Ziehe das Klebeband ab, welches den Vibrationsmotor bedeckt. Ziehe das Klebeband ab, welches den Vibrationsmotor bedeckt.
    • Löse vorsichtig die beiden Stecker unten am Telefon.

    • Ziehe das Klebeband ab, welches den Vibrationsmotor bedeckt.

  12. Nun lässt sich die Hauptplatine durch leichtes Anheben entfernen. Beim Ausbau der Hauptplatine wird die kleine Kunststoffmechanik des SIM Karteneinschubs lose und kann verloren gehen.
    • Nun lässt sich die Hauptplatine durch leichtes Anheben entfernen.

    • Beim Ausbau der Hauptplatine wird die kleine Kunststoffmechanik des SIM Karteneinschubs lose und kann verloren gehen.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

3 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

David Pugliese

Mitglied seit: 26.09.2017

1.089 Reputation

4 Anleitungen geschrieben

Team

USF Tampa, Team S2-G6, Passmore Fall 2017 Mitglied von USF Tampa, Team S2-G6, Passmore Fall 2017

USFT-PASSMORE-F17S2G6

4 Mitglieder

11 Anleitungen geschrieben

Hi where i can find mainborad for lg g6 h870

Zaid Nashwan - Antwort

How much access to the SIM Reader does this give you? A customer has broken his SIM Tray and there is a part stuck inside, will removing the board allow me to reach this or would I be removing it for no reason?

Any response appreciated, ty.

RDCharlton - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 2

Letzten 30 Tage: 19

Insgesamt: 5,911