Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Flip open the phone and locate the four screw covers.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove all four screw covers by using an IPod opening tool. They should come off relatively easy.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Using a T6 Torx screwdriver, remove all four screws.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Once the screws are removed, use an IPod opening tool to separate the front cover from the inner screen cover.
-
Run the Ipod opening tool down both sides,disconnecting the tabs that hold the covers together.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Pull the inner screen cover towards you and up in order to separate it from the front cover.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the tape from the bottom of the LCD screen.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Carefully lift the LCD screen and peel it from the gold ribbon. The sticky connection runs all the way around the LCD screen.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Flip the screen over so that you can see the outer LCD screen and the circuit board.
-
Insert spudger in the bottom right corner.
-
Lift up and move the spudger across the bottom.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the pointy side of the spudger to peel off the interior tape.
-
Flip the assembly over and peel the circuit board from the screen.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the spudger to remove the LCD screen from its backing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Carefully slide the spudger behind the main ribbon in order to separate it from the inside cover of the phone.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger to pop off the camera ribbon from the main ribbon. The camera component should separate entirely.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Poke out rubber covers using a spudger or pointy object, such as a thumb tack.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a T6 torx screwdriver to unscrew the 6 screws that hold the back casing on.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use IPod opening tool to separate back housing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Separate the back housing from the phone.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger to disconnect antenna wire.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the IPod opening tool to pop out the logic board.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the IPod opening tool to disconnect the main ribbon.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Once the ribbon is detached, remove the logic board and replace if necessary.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
The back of the keypad is shown here, next to the logic board (the logic board is turned over to expose the buttons).
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Using a spudger, lift the keypad off of the tabs.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Wedge a spudger or another harder prying tool in the connection between the top cover and the bottom cover on the right side.
-
Use a large amount of force to push the top cover off the bottom cover's blue extrusion.
-
When separating the top cover from the bottom cover, be careful not to tear the ribbon as you pull it out from the hinge.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Slide the ribbon out of the slot in the joint on the left side.
-
Pull the ribbon out of the top cover with your hand.
-
Once the ribbon is removed, you can replace the covers.
-