Einleitung

If the device is failing to boot, then the issue may lie with the motherboard. To replace this component, follow this guide.

Turn over the device so that the bottom is facing up. Make sure the hinged side is facing you.
  • Turn over the device so that the bottom is facing up. Make sure the hinged side is facing you.

Kommentar hinzufügen

Move the right switch towards the right until it clicks in place. You should then see the color red reveal from where the switch was originally.
  • Move the right switch towards the right until it clicks in place. You should then see the color red reveal from where the switch was originally.

Kommentar hinzufügen

  • Now take your left hand and slide the left switch to the left.

  • This switch will not click in place like the other switch, so make sure to keep your left hand on the switch.

Kommentar hinzufügen

  • Take your free hand and place it on the battery. Gently slide it away from its slot.

Kommentar hinzufügen

  • Rotate the laptop so that now the hinge is facing away from you.

  • Remove the two 2.5 x 4.0 mm Phillips #0 screws from the underside of the laptop.

  • Slide the bottom panel towards you until it stops, and then carefully lift it off.

Kommentar hinzufügen

  • Remove the three 2.0 x 6.0 mm Phillips #0 screws located on the underside of the device.

Kommentar hinzufügen

  • Turn the laptop right side up and open the lid.

  • Using the spudger and your fingers, get in between the keyboard's edge and lift it up.

  • Carefully lift the keyboard ribbon cable out of the socket it is in.

Kommentar hinzufügen

  • Remove the 2.5 x 6.0 mm Phillips #0 from the center of the device.

  • Close the laptop and place it face down once again.

Kommentar hinzufügen

  • If a hard disk drive is installed, remove the two 2.5 x 4.0 mm Phillips #0 screws.

  • Slide the hard disk drive out of its socket.

Kommentar hinzufügen

  • Remove the eleven 2.5 x 6.0 mm Phillips #0 screws.

  • Remove the three 2.0 x 3.0 mm flat head screws.

  • Remove the 2.5 x 4.0 mm Phillips #0 screw.

Kommentar hinzufügen

  • Turn the laptop right side up and open the lid.

  • Disconnect the two ribbon cables from the center.

  • Lift the keyboard bezel (with trackpad) straight up and out.

Kommentar hinzufügen

  • Remove the five ribbon cables on the top of the computer.

  • Gently remove the single cable from its socket.

Kommentar hinzufügen

  • Remove the three 2.5 x 3.0 mm Phillips #0 screws on the motherboard.

Kommentar hinzufügen

  • Using your fingers or a spudger, lift the motherboard slightly.

  • Detach the single cable from underneath.

  • Lift the motherboard the rest of the way out.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Alex Amorim

Mitglied seit 19.03.2018

689 Reputation

5 Anleitungen geschrieben

Team

UMass Dartmouth, Team S5-G2, Peak Spring 2018 Mitglied von UMass Dartmouth, Team S5-G2, Peak Spring 2018

UMASSD-PEAK-S18S5G2

2 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 9

Insgesamt: 63