Zum Hauptinhalt wechseln

Einleitung

There are a few reasons why you might want to replace the battery in your Lenovo Yoga 910-13IKB. Over time, batteries degrade and their ability to hold a charge diminishes, resulting in low battery life that might not be enough to get you through the day. In rare cases, it is possible for the battery to expand and push against the chassis and other components of the laptop. For users who wish to replace the battery on their device, Lenovo has made it easy to do so, only requiring a Phillips screwdriver.

  1. Before you begin, be sure to turn off your laptop and unplug it from the outlet. Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.
    • Before you begin, be sure to turn off your laptop and unplug it from the outlet.

    • Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.

    • Remove the panel.

  2. Remove all 4 screws attached to the battery with a small Phillips head screwdriver.
    • Remove all 4 screws attached to the battery with a small Phillips head screwdriver.

    • Each screw on the back is M2 x 1.7mm

    • After the screws are taken out, remove the battery.

  3. Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.
    • Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.

    • Each screw on the back is M2 x 1.7mm

    • Detach the ribbon cable connected to the trackpad using a wedge device.

    • Remove the trackpad using a wedge device

  4. Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.
    • Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.

    • Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

  5. Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver. Pull the SSD stick directly to the right until it shifts out of place to remove it. The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.
    • Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.

    • Pull the SSD stick directly to the right until it shifts out of place to remove it.

    • The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.

  6. Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver Remove the back connector strip using a wedge device to pry it off of the device With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.
    • Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver

    • Remove the back connector strip using a wedge device to pry it off of the device

    • With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.

  7. Remove the four 3 mm Phillips screws holding the battery in place.
    • Remove the four 3 mm Phillips screws holding the battery in place.

  8. Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. Pull parallel to the battery, not straight up. Pull evenly on the width of the cable so that no individual wire is overly strained.
    • Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery.

    • Pull parallel to the battery, not straight up.

    • Pull evenly on the width of the cable so that no individual wire is overly strained.

    • Lift the battery out.

Abschluss

To reassemble your device, follow these instructions in reverse order.

For optimal performance, after completing this guide, calibrate your newly installed battery.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Pablo Gonzalez

Mitglied seit: 23.01.2020

394 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team S1-G5, White Winter 2020 Mitglied von Cal Poly, Team S1-G5, White Winter 2020

CPSU-WHITE-W20S1G5

4 Mitglieder

12 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 9

Letzten 7 Tage: 40

Letzten 30 Tage: 163

Insgesamt: 3,198