Einleitung
Diese Anleitung zeigt, wie du beide Lautsprecher deiner Logitech UE Megaboom ausbauen und tauschen kannst. .
Was du brauchst
-
-
Fange an einem Ende des Lautsprechers an.
-
Führe ein Kunststoff-Öffnungswerkzeug in den Spalt zwischen dem Gummideckel und der Gewebe ein.
-
Hebele den Gummideckel mit einer Aufwärtsbewegung heraus.
-
Mache dasselbe auf der anderen Seite.
-
-
-
Benutze den Jimmy und hebele den Gummistreifen heraus auf dem sich die Lautstärke-Tasten befinden.
-
Entferne den ganzen Gummistreifen nach dem Heraushebeln.
-
-
-
Benutze eine Pinzette um die Kunststoffklemme anzuheben, die das Gewebe in der Röhre fixiert.
-
Hebe die Klemme rund um den Lautsprecher herum heraus.
-
Mache dasselbe auf der anderen Seite.
-
-
-
-
Ziehe am weißen Streifen um den Akku heraus zu nehmen.
This skipped the step of pulling out the circuit card on the battery charge/aux-in side. Pry up below the gasket next to the large capacitors on both sides.
A faire après les étapes 5 et 6 (pas besoin d’ouvrir l’autre côté de l’enceinte).
-
-
-
Entferne die innenliegende Kunststoff-Dichtung auf der Platine.
-
Entferne die zweite Kunststoff-Dichtung am äußeren Rand der Platine unter der Gummidichtung.
-
-
-
Setze ein Öffnungswerkzeug zwischen Grill und Gehäuse ein.
-
Heble nach oben, damit sich die Rasten lösen.
-
Wiederhole für den Grill über dem zweiten Lautsprecher.
-
-
-
Drücke den dünnen Metallstab an der Seite des Lautsprechers mit einem Öffnungswerkzeug heraus.
-
Fasse den Metallstab mit einer Spitzzange und ziehe ihn ganz aus dem Gerät heraus.
-
Entferne die anderen drei Metallstäbe.
-
-
-
Setze ein Öffnungswerkzeug zwischen Lautsprecher und Gehäuse ein.
-
Heble damit, bis sich die Laschen am Lautsprecher lösen.
-
Finde den Kabelanschluss des Lautsprechers auf der Platine und trenne ihn ab.
-
Wiederhole das Ganze für den anderen Lautsprecher.
-
Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
7 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
7 Kommentare
Thank you! I was able to glue one of the passive radiators back in place.
Where can I find a speaker replacement? Thanks for your time
I’ve got the same issue. Where can i find the speaker replacement?
For those looking for replacement speakers - either directly from Logitech ( $$$ ) or find a broken one on eBay that’s been water logged or some such thing and recover the speakers from that (since they are waterproof speakers)
Thanks for the article - turns out one of my speaker grills had popped loose and was imitating a blown speaker!
yes! same issue!
i bought a replacement speaker (which i still have if anyone is looking), but it was a speaker grill stopper that had come unglued and vibrated - sounding exactly as if a blown speaker or radiator.
Thank you for this detailed tutorial.
One important thing; do you know where can we buy 2 new speakers ? My UE mega boom fallen down from 4 meters and need to be repaired.
I already dismantle the Megaboom and detected that the 2 speakers are damaged.
Thank you in advance for your answer.
Romain P.
I use a product called Simply Speakers. speaker repair adhesive #MI-3035. Clean off old glue by applying pressure with your thumb and roll glue off the two faces, use alcohol to clean corners. It takes a little bit of rubbing. Apply a small line on mating surface (to much glue does not make a better seal). Put the two surfaces back together. Lay the radiator housing on a flat surface, Get something flat to put on top of the radiator and apply constant pressure for about 12 hrs (A couple of heavy books or anything with weight). I hope this helps someone.
Pry all the way around with the tool as there are “clips” that hold the cap in place all around beneath the cap. Avoid trying to “pull the lid open” from the opening of a half opened lid.
Jamin Hu - Antwort
Stop! Before you proceed, notice the comments at the end of the guide. You don't have to take apart both sides or remove the mesh fabric. Remove just the bottom cap (with the aux/charge plug).
Then carefully remove the glue securing the circuit board on the sides and gently pull the board out to reveal the battery under it.
Caleb Kelsay - Antwort
FWIW I had no luck opening these caps with the tools I bought on iFixit (plastic pry bar, metal Jimmy). I had a lot more luck using the flat edge of a butter knife! (it still took lots of work on my UE Megaboom 3)
Travis Taylor - Antwort