Zum Hauptinhalt wechseln

Mac Pro Ende 2013 AirPort Antennengruppe tauschen

Was du brauchst

  1. Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Äußeres Gehäuse: Schritt 1, Bild 1 von 2 Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Äußeres Gehäuse: Schritt 1, Bild 2 von 2
    • Schiebe den Verriegelungsschalter nach rechts in die entriegelte Position.

  2. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 2, Bild 1 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 2, Bild 2 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 2, Bild 3 von 3
    • Hebe das Außengehäuse gerade nach oben vom Mac Pro ab.

    • Es kann helfen, auf die Mitte des Lüfters zu drücken, während das Gehäuse nach oben gehoben wird.

  3. Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Lüftereinheit: Schritt 3, Bild 1 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Lüftereinheit: Schritt 3, Bild 2 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Lüftereinheit: Schritt 3, Bild 3 von 3
    • Entferne die fünf 5,1 mm T10 Torx Schrauben, die rund um die Lüftereinheit herum angebracht sind.

    You don't have to remove the fan assy to get to the wifi board & card. It can be done with the fan assy still attached.

    Fat Mango - Antwort

    Fat Mango is correct. That said. If you do pull the fan assembly note that the screws are all held in with blue Permatex and breaking them free takes a fair amount of effort. Getting a good set of Torx screwdrivers is a must.

    Jim WIlson - Antwort

    Hey guys, what would happen if you only replace one card.. I have a D300 but the plan is to upgrade to D500 or D600. So If I can afford and install one instead of the pair would it increase something? or will it cause any conflict? I guess I don’t understand if I the Mac Pro has 2 D300 graphic cards that means each has 1GB? Same as If I would Install 1 D600 that would increase 3GB only? Thanks.

    marcotamayo - Antwort

    D300 = 2GB each card. Very few apps uses two cards at the same time.

    Gio Cas -

    The (5) Screws are Apple part number 923-0713

    Steven Gier - Antwort

  4. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 4, Bild 1 von 2 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 4, Bild 2 von 2
    • Die Lüftereinheit ist mit zwei Kabeln mit dem Rest des Computers verbunden. Die Kabel befinden sich auf der Seite des IO Boards.

    • Kippe die Einheit nach oben, weg vom IO Board.

    • Versuche noch nicht die Lüftereinheit ganz zu entfernen, da sie noch durch zwei Kabel mit dem Computer verbunden ist.

  5. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 5, Bild 1 von 1
    • Halte die Lüftereinheit mit einer Hand fest und löse die zwei T8 nicht verlierbaren Schrauben in der Halterung des Lüfterkabels.

    • Diese Schrauben sind nicht-verlierbar und verbleiben daher im Mac Pro. Versuche nicht, die Schrauben aus deinem Mac Pro zu entfernen.

    On my Mac Pro (assembled mid-2017) these are T8 screws. In fact, there were no T7 screws anywhere in my machine.

    mark33 - Antwort

    There was no bracket on top of the cable at all, so I got a bit confused, so I had to skip step 5 and 6.

    Rakesh - Antwort

    On my machine, a TR7 worked to remove them due to the weird angle.

    Wilson Gaberino - Antwort

  6. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 6, Bild 1 von 1
    • Benutze eine Pinzette, um die Halterung des Lüfterkabels von der Lüftereinheit zu entfernen.

  7. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 7, Bild 1 von 2 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 7, Bild 2 von 2
    • Benutze das flache Ende eines Spudgers, um das Flachbandkabels der Lüftereinheit vom IO board zu trennen.

  8. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 8, Bild 1 von 1
    • Entferne das Antennenkabel der Lüftereinheit vom IO board.

    • Entferne die Lüftereinheit vom Mac Pro.

    You don't have to remove the fan assy to do the steps below. They can be done with the fan assy still attached.

    Fat Mango - Antwort

  9. Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Deckel der Lüftereinheit: Schritt 9, Bild 1 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Deckel der Lüftereinheit: Schritt 9, Bild 2 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen, Deckel der Lüftereinheit: Schritt 9, Bild 3 von 3
    • Heble mit dem flachen Ende des Spudgers den Deckel von der Lüftereinheit ab.

    • Entferne den Deckel der Lüftereinheit.

    There is a thin circle of double sided adhesive that must be loosened in order to remove the plastic cover.

    somethingorother - Antwort

  10. Mac Pro Ende 2013 AirPort Antennengruppe tauschen, AirPort Karte: Schritt 10, Bild 1 von 1
    • Entferne die drei 3,7 mm Torx T4 Schrauben, mit denen die Metallabdeckung über der Einbauöffnung für die AirPort-Karte befestigt ist.

    I had better luck using a T5 driver.

    somethingorother - Antwort

    Same here. Mine were T5, not T4.

    Carsten Clark - Antwort

    t4 was good for me

    Arden De Cuir - Antwort

  11. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 11, Bild 1 von 1
    • Hebe die Metallabdeckung über der Einbauöffnung für die AirPort-Karte hoch und entferne sie.

  12. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 12, Bild 1 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 12, Bild 2 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 12, Bild 3 von 3
    • Klappe den Sicherungsbügel am ZIF-Anschluss des Flachbandkabels der Lüftereinheit mit der Spudgerspitze hoch.

    • Löse das Flachbandkabel zur Lüftereinheit aus dem ZIF-Anschluss heraus.

  13. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 13, Bild 1 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 13, Bild 2 von 3 Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 13, Bild 3 von 3
    • Klappe den Sicherungsbügel am ZIF-Anschluss des Lüfterkabels mit der Spudgerspitze hoch.

    • Löse das Flachbandkabel zum Lüfter ab.

  14. Mac Pro Ende 2013 AirPort Antennengruppe tauschen, AirPort Antennengruppe: Schritt 14, Bild 1 von 1
    • Entferne die drei 3,7 mm Torx T4 Schrauben, mit denen die Antennenbaugruppe an der Lüftereinheit befestigt ist.

    Again, mine were T5 rather than T4. (Unless there's an off-by-one error in my Torx set ;-)

    Carsten Clark - Antwort

  15. Mac Pro Ende 2013 AirPort Antennengruppe tauschen: Schritt 15, Bild 1 von 1
    • Entferne die AirPort-Antennenbaugruppe.

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

3 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.560 Anleitungen geschrieben

2 Kommentare

having macpro 2013 bluetooth on issue, where is the bluetooth module locate?

Sanong - Antwort

is bluetooth module part of (inside) airport board?

Sanong - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 9

Letzte 30 Tage: 51

Insgesamt: 5,242