Zum Hauptinhalt wechseln

Mac mini Modell A1283 Festplatte tauschen

Grundständige Anleitung
Dies ist eine grundständige Anleitung, die nur als Teil einer anderen Anleitung verwendet werden sollte.

Was du brauchst

  1. Mac mini Modell A1283 Festplatte tauschen, Festplatte: Schritt 1, Bild 1 von 1
    • Entferne die beiden Kreuzschlitzschrauben, mit denen die Unterseite der Festplatte am inneren Rahmen befestigt ist.

    These are JIS screws. A J1 bit will fit better than a PH1 bit.

    michael - Antwort

  2. Mac mini Modell A1283 Festplatte tauschen: Schritt 2, Bild 1 von 1
    • Entferne die beiden Kreuzschlitzschrauben, mit denen die Festplatte seitlich am inneren Rahmen befestigt ist.

  3. Mac mini Modell A1283 Festplatte tauschen: Schritt 3, Bild 1 von 1
    • Der Thermosensor ist an der Seite der Festplatte verklebt. Heble ihn mit dem flachen Ende des Spudgers ab.

  4. Mac mini Modell A1283 Festplatte tauschen: Schritt 4, Bild 1 von 1
    • Löse das Klebeband, mit dem das Kabel zum Thermosensor an der Festplatte befestigt ist und entferne den Thermosensor.

    • Du musst den Thermosensor an der gleichen Stelle der neuen Festplatte befestigen.

  5. Mac mini Modell A1283 Festplatte tauschen: Schritt 5, Bild 1 von 2 Mac mini Modell A1283 Festplatte tauschen: Schritt 5, Bild 2 von 2
    • Schiebe die Festplatte in Richtung des Lautsprechers und trenne sie von der Verbindungsplatine ab.

    • Hebe die Festplatte an der Kante gegenüber vom Lüfter hoch und entferne sie vom inneren Rahmen.

    To reinstall drive, hold the internal frame upside down. This will make it easier to align the connector.

    eric - Antwort

    It was super frustrating getting the drive aligned, and when It finally did align, I forgot about the temperature sensor and managed to yank the wire out of the board. Hopefully I can adjust the fans manually and not have to reattach the wire, which doesn't really appear possible.

    Anyone ever do it?

    I wonder if the wire was the cause of my issue from the beginning, as now that the wire is gone, the drive slips right into place. So, if you're having difficulty getting the drive connected, make sure the temp sensor wire is out of the way.

    maccentric - Antwort

    So, looking back, I now see that the sensor cable routs on top of the drive, not underneath.

    maccentric -

    When putting a new drive in you need the spudger to hold the bottom of the drive in place though the side opening while you slide it into the sata connectors with your hand or a dull side of a screw driver. It wont damage anything [edit] (the spudger through the side hole) although it seems like you're forcing it. I did it twice because of the same problem with the wire getting caught. Rather than pull on the wire I just removed the drive and realigned the sensor. It's easy with the spudger.

    maxcsmith - Antwort

    It's really not that hard getting the new drive in and avoiding the wire. Move the wire out of the way! Drop the drive in, at an angle under the screw holes adjacent to the fan. Slide along the bottom until it touches the end where the connector is. Turn upside down and push in.

    Andy D - Antwort

    عالی بود ممنونم

    Hamid Sayadi - Antwort

Abschluss

Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Ein Kommentar

For all those poor people who have wrecked their Minis by following the bad advice on this page, I fixed mine by replacing this part:

http://www.powerbookmedic.com/Mac-Mini-I... (Apple part no 922-8807).

I did manage to solder a connector back onto the visible contacts on my original board, but it didn't work; the replacement worked fine.

If your cable is damaged too, you'll need to replace that too, but note that there are several different ones, and SKU17434 (Apple part 922-7319) is NOT compatible with the above board. I don't know the exact model of cable - having received the wrong one I managed to repair my original one.

Marcus Bointon - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 1

Insgesamt: 2,078