Zum Hauptinhalt wechseln

MacBook Air 13" (Ende 2020) Display tauschen

Was du brauchst

  1. MacBook Air 13" (Ende 2020) Display tauschen, Schrauben an der Unterseite entfernen: Schritt 1, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Magnetic Project Mat
    $19.95
    Kaufen
    • Bevor du anfängst, solltest du die Auto Boot Funktion deaktivieren. Auto Boot schaltet deinen Mac beim Aufklappen ein und kann während des Öffnungsvorgangs versehentlich ausgelöst werden. Benutze diese Anleitung oder folgende verkürzten nachfolgenden Anweisungen um Autoboot auszuschalten.

    • Wenn dein MacBook unter BigSur v11.1 oder einer späteren Version läuft, lässt sich AutoBoot möglicherweise nicht stilllegen. Arbeite zuerst normal weiter, trenne aber den Akku sofort ab, wenn du ins Innere des Gerätes hinein gekommen bist.

    • Schalte dein MacBook vollständig aus und ziehe den Stecker aus der Steckdose, bevor du anfängst. Schließe das Display und drehe den Laptop um.

    • Entferne folgende P5 Schrauben:

    • Zwei 7,9 mm Schrauben

    • Zwei 7,3 mm Schrauben

    • Sechs 2,6 mm Schrauben

    • Halte während der gesamten Reparatur deine Schrauben gut geordnet und achte darauf, dass jede Schraube an ihren Ursprungsort zurück kommt.

    ESD safe mat, plugged into ground, with a wrist strap, also grounded, are the best best to protect the logic board.

    Robin Ray - Antwort

    Re-Assembly Tip: Before putting the screws back in, snap the lower case on and test to make sure the MacBook powers up. When I first re-assembled, I became very nervous I did something wrong because it would not power on. It turns out I just needed to plug the laptop into a power source for it to power up (despite having a good charge before disassembly). It was the perfect way to test the new USB-C ports!

    Austin - Antwort

    Big points to this one, especially for mentioning needing to plug the laptop in. The bottom case needs to be screwed in and laptop needs to be plugged in before it will boot.

    Bayden Yazalina -

    Wiha 4PL driver for these screws.

    Greg Worrel - Antwort

    Printing out all the images from this Ifixit guide prior to starting and using duct tape help me keep track of screws.

    raju midjdeya - Antwort

  2. MacBook Air 13" (Ende 2020) Display tauschen, Unteres Gehäuse entfernen: Schritt 2, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Unteres Gehäuse entfernen: Schritt 2, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Unteres Gehäuse entfernen: Schritt 2, Bild 3 von 3
    • Zwänge deine Finger zwischen das Display und das Gehäuseunterteil und ziehe nach oben, so dass sich das Gehäuseunterteil vom Air ablöst.

    • Entferne das untere Gehäuse.

    • So wird das untere Gehäuse wieder eingebaut:

    • Setze es passend auf und drücke fest darauf, damit die beiden darunter versteckten Rasten einschnappen. Du solltest das hören und spüren können.

    Los tornillos se ruedan fácilmente :(

    Mishelle Cerón - Antwort

  3. MacBook Air 13" (Ende 2020) Display tauschen, Akku abtrennen: Schritt 3, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Akku abtrennen: Schritt 3, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Akku abtrennen: Schritt 3, Bild 3 von 3
    • Heble den metallenen Sicherungsbügel am Akkustecker mit dem flachen Ende des Spudgers hoch und entriegelt den Akkustecker.

    • Achte darauf, dass der Sicherungsbügel nicht mehr in die Lasche der Verriegelung eingreift, bevor du den Akkustecker heraushebst. Der metallene Sicherungsbügel sollte sich leicht öffnen lassen.

    • Ziehe den Sicherungsbügel senkrecht nach oben, damit der Akkustecker aus seinem Anschluss auf dem Logic Board herauskommt.

    • Drücke den Stecker beim Zusammenbau gerade in seinen Anschluss hinein und achte darauf, dass er bündig im Anschluss sitzt.

    • Drücke, falls nötig, zuerst die hintere Seite mit den Kabeln fest, dann die vordere Seite des Steckers.

    Reassembly: I had difficulty going straight down. The connector has some angled edges that made it difficult. Instead, I slotted the wire side in first, then rocked it forward towards the hinge into position.

    Sean K - Antwort

    If having difficulty in flipping the bar up, place the machine vertical and not that there is a small “locking nib” that the bar has to clear. You may have to give the bar honest persuasion to clear the nib.

    Harry Dulcamara - Antwort

  4. MacBook Air 13" (Ende 2020) Display tauschen, Antennenkabel abtrennen: Schritt 4, Bild 1 von 1
    • Entferne die 1,4 mm Torx T4 Schraube, mit der die Abdeckung des Antennenkabels befestigt ist.

    • Wenn sich das T3-Bit doch etwas zu klein anfühlt, dann versuche es mit einem T4.

    I needed a T4 for this

    MaFt Morley - Antwort

    Wiha tools T3 fit perfectly.

    Robin Ray - Antwort

    I found this screw difficult to reinstall. Very small and fiddly. 15-20 minutes on this step.

    Harry Dulcamara - Antwort

    The T3/T4 screws are tiny!!!

    raju midjdeya - Antwort

    To reinstall a tiny screw first turn it counterclockwise until you feel it engage the tread, then turn them clockwise to tighten it.

    Patrick Langvardt - Antwort

  5. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 5, Bild 1 von 1
    • Entferne die Abdeckung des Antennenkabels.

    Make sure the 90 degree bend on the cover is towards the hinge when reassembling. It will fit in backwards, but will cause problems.

    Robin Ray - Antwort

  6. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 6, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 6, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 6, Bild 3 von 3
    • Greife den Antennenstecker mit einer Pinzette nahe am Anschluss an.

    • Ziehe ihn gerade nach oben und trenne das Kabel ab.

    • Wiederhole das Ganze für das zweite Kabel.

    • Halte die Stecker beim Zusammenbau an ihre Positionen und drücke sie behutsam gerade nach unten. Die Stecker rasten in ihre Anschlüsse ein.

    These are tiny, and hard to reconnect. The key was to position the cables so their ends are very close to the posts on the board.

    dexter - Antwort

    Yep. Good call. Me too folks.

    Harry Dulcamara -

    So anyone that’s had experience with keyboard and antenna, connectors, or previous Apple iPhone products, knows that these antenna connectors go on from front to back so you kind of have to position the noncable end of the antenna cable first and then push it towards the back I’m not sure if that makes sense, but try from the front to the back connecting Put pressure on the front first and then put pressure towards the cable in if you do it wrong and put too much pressure in it, you can ruin the cables. Be careful with it.

    babs martin - Antwort

  7. MacBook Air 13" (Ende 2020) Display tauschen, Displaykabel abtrennen: Schritt 7, Bild 1 von 1
    • Entferne die beiden 1,5 mm Torx T3 Schrauben, mit denen die Abdeckung des Displaykabelsteckers befestigt ist.

    None of the screws in this repair are T3. All the smaller ones are T4. Which is good, ‘cause my (cheap) repair tool kit doesn’t have a T3.

    dexter - Antwort

    The T3 screws called out were indeed T3, not T4 on the MacBook Air I replaced the display on.

    --Mac Ace, Inc.

    Robin Ray - Antwort

    I dropped one of these - can they be purchased? Or is there a matching screw in an older MacBook Air? I have a ton of those for parts... :-)

    Jimmy Anderson - Antwort

    weird, for my model A2337 it is even T2 screws. tested it two times and I have the ifixit mako precision bit set.

    Otto Klassen - Antwort

    On my MacBook Air M1 Early 2020, I had to use a T4 bit on one of the screws. The other one came out with a T3. I am using a HyperTough 77-piece precision repair set.

    Raj Venkat - Antwort

  8. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 8, Bild 1 von 1
    • Entferne die Abdeckung des Displaykabelsteckers.

  9. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 9, Bild 1 von 2 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 9, Bild 2 von 2
    • Heble den Displaykabelstecker mit dem flachen Ende des Spudgers von der Antennenplatine hoch.

    • Um Druckstecker, wie diesen hier, wieder anzuschließen, musst du ihn erst sorgfältig ausrichten und auf einer Seite herunterdrücken, bis er einrastet. Wiederhole dann das gleiche auf der anderen Seite. Drücke nicht in der Mitte. Wenn der Stecker schief sitzt, können die Kontakte verbogen und dauerhaft beschädigt werden.

    Since this step is the most crucial in the reassembly process I suggest connecting the flat cable to the board BEFORE placing the board in to its cavity in the antenna bar. MUCH easier and SAFER to do.

    J Patrick Dowling - Antwort

  10. MacBook Air 13" (Ende 2020) Display tauschen, Schrauben der Antennenleiste entfernen: Schritt 10, Bild 1 von 1
    • Entferne die folgenden sechs Torx T5 Schrauben, mit denen die Antennenleiste befestigt ist:

    • Vier silberfarbene 7,4 mm Schrauben

    • Zwei schwarze 4,7 mm Schrauben

    Mine here is T6 Torx not T5.

    David Jones - Antwort

    When putting it back together, make sure to get the display cable connector out from under the antenna board before screwing the antenna bar back down. The connector has to go behind the bar in the little notch as the board goes through the opening in the bar.

    Matthew Granger - Antwort

    Mine here were Torx T4. Came with the kit.

    Jace Sheppard - Antwort

    My 4.7 mm screw is stripped.

    Any suggestions to get it removed?

    B S - Antwort

    B S,

    Darn, sorry that happened! Here's a guide with five different methods you can try to get it loose: Wie man eine rundgedrehte Schraube entfernt

    Best of luck!

    Carsten Frauenheim -

    These are T5. A T4 might work but you might strip it.

    A T6 shouldn't fit at all; if it does, your driver is either worn or just poor quality.

    maccentric - Antwort

  11. MacBook Air 13" (Ende 2020) Display tauschen, Antennenleiste entfernen: Schritt 11, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Antennenleiste entfernen: Schritt 11, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Antennenleiste entfernen: Schritt 11, Bild 3 von 3
    • Setze die Spudgerspitze in den Spalt zwischen Antennenleiste und Displayscharnier ein.

    • Kippe den Spudger gegen das Scharnier und heble das Ende der Antennenleiste hoch.

    • Wiederhole das Ganze am anderen Ende der Antennenleiste.

  12. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 12, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 12, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 12, Bild 3 von 3
    • Hebe die Antennenleiste mit den Fingern gerade nach oben vom Gehäuse weg.

    • Die Antennenleiste ist verklebt, eventuell ist etwas Kraft nötig, um sie abzulösen.

    • Führe die Antennenplatine durch die Öffnung in der Mitte der Antennenleiste.

    • Achte darauf, dass die Flachbandkabel zur Antennenleiste nicht übermäßig angespannt werden.

    • Entferne die Antennenleiste.

    Separating antennae bar from case after removing screws is challenging. Author’s directions are good but what needs to be addressed is a thin strip of adhesive on both sides of the bar that needs to be separated. the strips are located on the hinge edge of the logic board mount area. I used a metal, razor thin, wide, blade type spudger to gently “wedge” underneath the bar along both adhesive strips to loosen the bar and lift it up. Careful!

    Macrepair SF - Antwort

    Thanks for this hint!!

    Benjamin Bradshaw - Antwort

    Before removing the antenna bar see if the right side is slightly elevated than the left. Upon replacement I could not get the right side to sit as flush as the left. However it may be intentional to protect the wifi wires.

    Harry Dulcamara - Antwort

    I was stuck on this step (removing the antenna bar) but this video helped me: https://www.youtube.com/watch?v=tHhHNjzO...

    Matthias - Antwort

  13. MacBook Air 13" (Ende 2020) Display tauschen, Vier Scharnierschrauben entfernen: Schritt 13, Bild 1 von 2 MacBook Air 13" (Ende 2020) Display tauschen, Vier Scharnierschrauben entfernen: Schritt 13, Bild 2 von 2
    • Entferne die beiden 5 mm Torx T8 Schrauben an jedem Scharnier (also insgesamt vier).

    • In der Mitte jedes Scharniers gibt es eine dritte Schraube, die zunächst noch nicht entfernt wird.

    The Easiest Mac screen repair I've ever done! it was a pleasant surprise

    Kelly Legner - Antwort

    I found a T9 to be a better fit

    Luke Knight - Antwort

    Nothing is making these screws come out. Any advice on what to do

    ella sharman - Antwort

    Increase the diameter of the handle. That gives more torque to break the screww loose. You could wrap it with some material and then cover it with duct tape.

    Matthew Granger -

    TR9 Screw in my Mako Precision Bit set from ifixit.

    Otto Klassen - Antwort

  14. MacBook Air 13" (Ende 2020) Display tauschen, MacBook ganz öffnen: Schritt 14, Bild 1 von 2 MacBook Air 13" (Ende 2020) Display tauschen, MacBook ganz öffnen: Schritt 14, Bild 2 von 2
    • Lege das MacBook weiterhin mit dem Display nach unten. Hebe das obere Gehäuse vorsichtig an, um das MacBook soweit wie möglich aufzuklappen.

  15. MacBook Air 13" (Ende 2020) Display tauschen, Die beiden übrigen Scharnierschrauben entfernen: Schritt 15, Bild 1 von 1
    • Stelle das MacBook auf die Seitenkanten, wobei das Display von dir weg zeigt.

    I find it easier to place the macbook on a table with keyboard down and the screen hanging over the side. Much less cumbersome, especially when putting the new screen in place.

    maccentric - Antwort

  16. MacBook Air 13" (Ende 2020) Display tauschen: Schritt 16, Bild 1 von 2 MacBook Air 13" (Ende 2020) Display tauschen: Schritt 16, Bild 2 von 2
    • Benutze einen T8 Torx Schraubendreher, um die beiden 5 mm Schrauben, jeweils eine auf jedem Scharnier, zu entfernen, mit denen das Display befestigt ist.

    • Wenn die beiden Schrauben weg sind, ist das Display nicht mehr mit dem oberen Gehäuse verbunden. Halte beide Hälften gut fest.

    My first attempt at reassembly had the hinge making a terrible snapping sound due to pushing some plastic parts out of the way at full extension. After screwing in these first two screws, I suggest opening and closing the hinge a few times to confirm it's smooth and quiet. If not, you have a fraction of a millimeter of play to get it into just the right position.

    Sean K - Antwort

    On disassembly and reassembly, keep in mind that the edge of the leaf of the hinge (the part with the 3 holes in it--red circle in picture above) sits slightly under a metal edge, and the barrel or pivoting part of the hinge is tucked under the forward-sloping edge of the case. This means the hinge doesn't just loosen and come out. It helps to lift the leaf free of the metal edge in front of it. Yes, this takes more force than you think it might. This will allow the entire hinge to be lifted up and forward (toward the front of the computer) out of its place under the edge of the case.

    Robert - Antwort

  17. MacBook Air 13" (Ende 2020) Display tauschen, Display entfernen: Schritt 17, Bild 1 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Display entfernen: Schritt 17, Bild 2 von 3 MacBook Air 13" (Ende 2020) Display tauschen, Display entfernen: Schritt 17, Bild 3 von 3
    • Schließe vorsichtig das Display, bis es etwa rechtwinklig zum oberen Gehäuse steht.

    • Die Scharniere sollten dabei ein wenig aus dem Gehäuse herauskommen, während das Display in Richtung des Gehäuses bewegt wird.

    • Halte das Display weiterhin senkrecht zum oberen Gehäuse, halte das Gehäuse fest und bewege das Display von diesem weg. Die Scharniere sollten aus der Unterseite des Gehäuses herausgleiten.

    • Entferne das Display.

    • Wenn du das Ersatzdisplay montiert hast, kann es sein, dass das MacBook möglicherweise nicht startet, solange das Netzteil nicht angeschlossen ist.

    I managed to try to fit the screen back to the body backwards, and wondered why the hinges didn't fit! Yes, stupid. I lost situational awareness. But just make the sure the correct side of the screen is facing the right way, to avoid my (temporary, but stressful) goofup.

    dexter - Antwort

    Me too until I read your comment. Remember that the screen was facing away from you in step 16. Then it fits easily.

    Matthew Granger -

    Like Dexter and Matthew I also initially tried to fit the display on backwards. I'm sure a lot of people are laughing at this mistake but if you're not paying attention it can happen. After 10 minutes having no success mounting the display I looked at the comments and had a DUH moment myself. In the correct orientation the mounting process is straightforward. Thanks Dexter for breaking the ice on this embarrassing situation!

    Patrick Langvardt -

    Nicely done guide, thank you Carsten!

    MotorMac - Antwort

    When you're all done with reassembly you have to plug the charger into the laptop in order for it to boot. It doesnt matter if the battery is charged it will not boot until the charger is reconnected. Took me a while to figure out why mine wasnt booting after the screen replacement

    Nelson Pun - Antwort

    Yep me too. Use the charger folks.

    Harry Dulcamara -

    Excellent guide. Concise, accurate, very nice!

    Robin Ray - Antwort

    I replace the screen and the computer is currently plugged into a power source, however I cannot get the computer to actually turn on. It just shows the charging display icon when I try to turn the computer on.

    Nicole - Antwort

    The true tone function will be lost even if you replace the display with a 100% compatible display.

    KazuhiroOshiyama - Antwort

    Even the display that is purchased through the Apple Parts store? I have one coming and will report back once I install it.

    Mike Hiteshew -

    Confirmed that all features function as new when using a display from Apple Parts - True Tone, Camera, Nightshift, etc.

    Mike Hiteshew -

    Perfect guide. I didn't encounter any issues and just worked carefully and gingerly.

    Toby Phillippe - Antwort

    Great guide - excellent photos and description. Very accurate. Thanks for creating!

    Mike Hiteshew - Antwort

    **************************** IMPORTANT SAFETY TIP************************

    I pulled another common mistake probably. Make sure that the screen cable is snaked through to the bottom when reattaching the new screen assembly. I didn't. I got all 6 screws on and closed the screen. I was up to step 12 when I realized there was no antenna board. Luckily it didn't break the screen again when I closed the cover on it!

    Matthew Granger - Antwort

    Excellent instructions. Did not take long at all. Every step is on point.

    Bayne Schulstad - Antwort

    Hey, great instructions - thanks! I'm pretty clumsy, and these screens are pretty fragile, which means I'm currently on my 4th screen! I have replaced them all myself following these instructions, and I've bought genuine parts AFAIK. However, for each replacement, I can never get the camera to work. It shows in System Information like so:

    ------

    Model ID: FaceTime HD Camera

    Unique ID: EAB7A68F-EC2B-4487-AADF-D8A91C1CB782

    ------

    But it just isn't recognised by any app, and whatever I try (killing all apps that might be using it, updating software etc) doesn't work, and hasn't worked with the two previous replacements either. I'm sure the connectors have been done properly on all of them. I read somewhere that running some system config software is necessary, but is that true? And if so where can I find it please?

    Thanks!

    Jeff G - Antwort

    Same problem, the camera does not work. Have you found the solution ??

    Laurent -

    Excellent instructions! 5 stars for the author. Take your time, lay out the screws you remove in a pattern to facilitate reinstallation. From a novice here, think twice before screwing anything back in place. I installed the screen only later to see the antenna rack facing the outside of the computer and not the motherboard. Problem resolved, everything works!

    Aldo Ciccotelli - Antwort

    I changed my screen. I am able to boot but the screen is totally black.

    irmb r - Antwort

    I would add an extra warning to the last instruction here...

    On my first attempt, the old screen hinges slipped out of the frame quite easily, which fooled me into thinking the new one would slip into place easily. It did not.

    The new screen got stuck, and in the process of trying to get it unstuck, the whole assembly slipped sideways by about an inch, and one of the display ribbon cables got sliced in half. 💀

    My advice: Practice getting the hinges back into place with the old screen. Only attempt the new screen once you've got the hang of what to expect when rotating it into place.

    Peter Gaultney - Antwort

    Awesome guide! Thank you. My removal and replacement went smoothly!

    Darrell Wicker - Antwort

    Patrick's Plan to attach new screen:

    1. Lay Mac - keyboard DOWN - hinge side toward U on the table.

    2. Pull it toward U till about an inch off the hinge end extends over the table edge.

    3. Using needle nose pliers open the hinges of the screen to just a bit MORE than 90º.

    4. Turn the screen hinge-side UP screen facing AWAY from your belly.

    5. Extend the video connector assembly fully on to the computer.

    5. Fit the hinges - 1 side at a time - into their notches on the computer.

    6. Press them in firmly with your thumbs

    7. Insert and tighten the CENTER screw on BOTH sides.

    8. PIck up the Mac & close it, S L O W L Y.

    VOILA! It's in there. Right...? ;-}

    Now open it up and finish re-assembly.

    J Patrick Dowling - Antwort

    以下供参考:

    更换屏幕总成后如果开机无反应,可以拔掉天线板小排线(紧挨着屏幕排线的那根),然后连接充电器后再尝试一下开机,如果能开机就稍微擦拭(吹)一下排线及排线扣,再接好排线开机即可(当拔掉这根排线开机时可能电量显示不足,不用担心)

    Justin Tan - Antwort

Abschluss

Vergleiche dein Ersatzteil mit dem Originalteil — möglicherweise musst du fehlende Bauteile übertragen oder Schutzfolien vom Neuteil abziehen, bevor du es einbauen kannst.

Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.

Es kann sein, dass das Laptop sich nach der Reparatur nicht gleich anschalten lässt. Schließe es dann erst an das Netzteil an.

Entsorge deinen Elektromüll fachgerecht.

Hat die Reparatur doch nicht den richtigen Erfolg gebracht? Frage in unserem Forum nach Hilfe.

114 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Carsten Frauenheim

Mitglied seit: 03/10/20

110.900 Reputation

338 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.560 Anleitungen geschrieben

50 Kommentare

How to make the True Tone working on the screen from another air?

William Kang - Antwort

The screen that your replacing should have true tone built in, it is a part of the display.

h_man08 -

Like iPhones does the display need to be programed to allow true tone to work?

Zuhayr Muse - Antwort

Just did the replacement! Was a breeze, just be careful not to over tighten any of the screws past a firm twist. Accident broke the head off a 1.5mm screw using a T3 bit. Didn’t affect the plates ability to cover or apply a firm press downwards, but a unfortunate thing nonetheless.

Caleb Stewart - Antwort

After Replacing the display, the new display is dim and the F2 does not brighten the screen. Any resolution to this issue?

Already reset NVRAM and PRAM.

Beto Beto - Antwort

same issue here. it looks more dim

Boy Named Kelly -

Step 4 and 7 were T4 Torx screws for me.

Thomas Anderson - Antwort

Install took about 30 min. and was pretty easy. I didn’t have trouble throughout the process. The adhesive on antenna plate was pretty strong, but with some gentle prying it came free.

shwinston - Antwort

I successfully installed the replacement screen, but now my 2.4 Ghz wifi / bluetooth antenna is not working. Any idea which connector cable connects to 2.4 Ghz antenna?

Lars - Antwort

I had the same problem. The reason was that I didn't connect the antenna back completely. Redo the step n. 6 in reverse and connect the antenna right (it must click).

Mirek Šiřina -

Thanks made it easy

Papi - Antwort

Done. Works . Biggest chalange was with plugging in back the display cabel connector . Be sure to pre alling the Screen bar with cabel conector , becouse it cannot bend on sides.

Jakub Reginia - Antwort

I tried the replacement. Everything works except True Tone as expected. Probably special tool is needed for the True Tone.

Ryan Kojima - Antwort

I’ve got the display from an Intel 2018 Air. Can I test it with an M1 Mac? The process and connectors look the same.

Jon - Antwort

Did you try this? If so, was it successful?

Lee -

Just tried this - it doesn’t work. M1 MacBook refuses to power on when connected to a display from a 2018 MacBook Air a1932.

Robert Corlett -

Your instructions were amazing and to the T. Thank you so much for everything

willblakleycomputes - Antwort

Hi.

Would the display of a MacBook Air early (intel) 2020 work on this MacBook Air late 2020. Seems to be the same specifications.

Marc Machold - Antwort

I change my screen but the camera doesn’t work, I checked the hardware’s but MacBook doesn’t have any camera, I tried 3 different screens , all are same. i tried all resets but still not working, any ideas?

Erhan Engin - Antwort

hi i have the same Issue do you have a solution?

Philipp Kuhn -

same problem here!

Pomar Filmes -

Same problem here, it seems we need the « system configuration tool » from Apple to make it works.

Laurent -

Hey, I have this same issue. It seems we need some software provided by apple(Only if you buy from their self service website) which i didnt..... Has anyone found a fix?

Jake Wakeman -

I have the same issue, I've tried two OEM screen replacements and now I purchased a genuine Apple M1 2020 screen in perfect working condition. Camera still does not work, but it is recognized in the system report. I've tried all the software fixes, resetting Pram and Nvram, terminal etc. Seems to be a hardware issue. Can I replace the cable for the insight camera?

johnalancovey -

Does this repair cause any feature issues? so, would the webcam not work or truetone not work? Even if i use genuine, donated apple parts?

Thank you!

Jubi Q - Antwort

I did encounter these issues with a genuine donated apple part...

Jake Wakeman -

Third-party screens may be missing the fat-L shaped shields and T3 screws flanking the display connector (visible in Step 9), if you bought one somewhere else be sure to transfer this hardware as well.

cressandy - Antwort

Certain parts like displays, cameras, and ambient light sensors have calibration values that are customized to each individual part during manufacturing. Transferring these values ensures maximum performance and quality after a repair.

A System Configuration step may be required at the end of your repair. System Configuration is a postrepair software tool that completes the repair for genuine Apple parts. Running System Configuration has a number of purposes that vary based on the part replaced.

Tony Fresquez - Antwort

Where do I get this software? System Configuration ? After three displays, including one Genuine Apple Display taken from a working MBA, with no defects, I can't get the camera to work. It is recognized by the system report

johnalancovey -

I'd replaced replaced the display on a MBP 2012 before, so I didn't anticipate any problems replacing the display on my A2337. Everything seemed to go smoothly, but when I booted up (with power cord attached), I didn't get more than a faint glow from the screen. I tried all the usual, but still no luck. I went back and made sure everything was seated properly but I got the same results. So, I reinstalled my cracked screen, which worked perfectly, outside of the cracks. You think I can assume the part was defective? I bought it from eBay, and it at least claimed to be OEM.

Pia Vastatrix - Antwort

Did you find a solution?

Stefan Schötz -

Is there a way to tighten the hinge? I would like to have my display tighter. It always flips back when I pick up my MacBook. That's not the case for my girlfriends MacBook which is the exact same model.

Marcel Braun - Antwort

It disappeared after replacing the display of macbookair m1! I put it back, but it doesn't work! However, I know I can go into recovery mode and DFU mode, but I get an error and can't restore! What should I do?

河田かずま - Antwort

All went great, very detailled manual. Unfortunately the new display doesn't work. The backlight is on but it shows no graphics. I managed to get the mac working with an external display. MacOS shows the display but nothing happens. Connectors are all doublechecked of course. Any ideas?

Stefan Schötz - Antwort

Additional info: It is a M1-Macbook Air A2337.

Stefan Schötz -

Where did you buy the display module, please?

Sebastian Slania -

すみません、macbookair m1の交換用のスクリーンをインストールする方法を教えてください!

河田かずま - Antwort

Apple only sells the display itself with our the clamshell. That makes the repair so much more complicated and I am sure they know it. Any ideas how to get the entire display module including the clamshell?

Sebastian Slania - Antwort

Sebastian,

The display part Apple sells through Self Service Repair is the entire assembly/module, including the panel, aluminum shell, camera, hinges, etc. The display we sell is also the entire display assembly. Hope this helps—happy fixing!

Carsten Frauenheim -

I replac the display the on MacBook Air but the display is not turning on I do not no what to do??

info - Antwort

This tutorial has been a life saver! Thank y’all so much!

Only snag I came across was on installing the replacement screen as the screen is easily damaged when getting the hinges to connect. So it’s important to be super careful at that part!

Briana - Antwort

This was so helpful. Thank you,

B S - Antwort

Used the iFix kit to replace a cracked screen on my daughter’s MacBook Air. Has been working without any issues. Now today, went to power it on, the screen is black. Powered on and off. Still not getting anything on the screen

Rob - Antwort

It worked pretty well, only removing the antenna was quite hard.

When I turned on the device the battery was not recognized so I had to re-connect the battery and then it worked.

Fabio L - Antwort

PLEASE HELP:

I followed this guide and although the antenna bar was kind of tough to remove, everything seemed to work fine. I replaced the screen and reassembled my MacBook Air. Everything works fine. BUT for the wifi. It works but signal is ridiculously low. Unless my M1 is within 3m and in direct sight of my router, wifi signal is gone or at 1 bar (out of 3). I have reopened the M1 and checked all the connectors: they all seem fine. Any suggestions?

Matthias - Antwort

The steps were clear and to the point. Great job on write up. Had no issues with the screen replacement and the unit fired right up after. The reconnect of the antenna was the scariest part just did not feel that the reconnect went well. You might do a follow up and just focus on that step on the reassemble.

markanderson - Antwort

Mike, that step was missing reassembly information. I added it in. Thanks for the callout, and I'm glad your repair went well!

Carsten Frauenheim -

does anybody knows if a 2021/2022 MacBook air M1 display is compatible? apparently Intel ones arent as they refuse to boot

Leo - Antwort

Leo, the Intel variant Air would be the early 2020 model. The late 2020 M1 model is different. And 2022 M2 displays are not compatible. Hope this helps!

Carsten Frauenheim -

Guide worked well, took about an hour. Thought I lost one of the tiny plate screws and searched forever then realized the WiFi cable cover is only one screw.

Because the antenna is difficult to start to pry up, suggest you do what I did and unscrew the hinge screw that is just under the antenna as this works to break the seal on the adhesive. Then of course screw it back in and pry/insert with your plastic tool to detach the rest of the adhesive.

Take your time and if you are old like me get a bright light and a magnifying glass/headset. Helped getting the little screws in and making sure the connectors for the antenna, display and power were in properly.

Joseph Collins - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 318

Letzte 7 Tage: 1,854

Letzte 30 Tage: 9,379

Insgesamt: 197,347