Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. , Akku: Schritt 1, Bild 1 von 1
    • Drehe die Verschlussschraube des Akkus mit einer Münze oder einem Spudger um 90° im Uhrzeigersinn.

  2. : Schritt 2, Bild 1 von 1
    • Hebe den Akku aus dem Computer.

  3. , Speicherabdeckung: Schritt 3, Bild 1 von 1
    • An der Rückwand des Akkufachs befinden sich im gleichen Abstand drei Kreuzschlitzschrauben. Drehe sie heraus.

    • Die Schrauben bleiben in der metallenen Speicherabdeckung hängen.

    • Beim Wiedereinbau des Akkufachs musst du den Schaumstoff hinter der Rückwand mit einem Spudger wieder einsetzen, damit der Akku im richtigen Abstand bleibt.

  4. : Schritt 4, Bild 1 von 1
    • Hebe die L-förmige Speicherabdeckung hoch, schiebe sie nach rechts und hole sie aus dem Computer.

  5. , Obere Gehäuseeinheit: Schritt 5, Bild 1 von 1
    • Entferne die 3 folgenden Schrauben in der Computerunterseite

    • Eine 1mm Phillips #00 in der Mitte des Gehäuses

    • Zwei 14,5mm Phillips #00

    • Wenn die Schrauben im Gehäuse liegen bleiben, kannst du einen Magnetischen Schraubenzieher nutzen um sie herauszuziehen.

    • Die kürzere der drei Schrauben gehört in das mittlere Gewinde

  6. : Schritt 6, Bild 1 von 1
    • Entferne die folgenden 3 Schrauben an der Rückwand des Batteriefachs:

    • Zwei 3 mm Kreuzschlitz #00. (A1181 hat drei 3 mm Schrauben und eine 4 mm.)

    • Eine 4 mm Kreuzschlitz #00 auf der rechten Seite.

    • Drücke beim Wiedereinbau dieser Schrauben leicht auf das untere Gehäuse, um die Schraubenlöcher auszurichten.

    • Es passiert schnell, dass diese Schrauben runddrehen, sei also besonders vorsichtig beim Herausdrehen.

  7. : Schritt 7, Bild 1 von 1
    • Entferne die beiden 6-mm-Kreuzschlitzschrauben #00 auf beiden Seiten der rechten Wand des Batteriefachs (nicht die, die dem Batterieanschluss am nächsten sind).

  8. : Schritt 8, Bild 1 von 1
    • Entferne die vier 3 mm Krezuschlitzschrauben #00 an der Vorderwand des Batteriefachs. Arbeitevon links und entferne die 2., 4., 7. und 9. Schraube.

  9. : Schritt 9, Bild 1 von 1
    • Entferne die folgenden 4 Schrauben auf der Rückseite des Computers:

    • Zwei 7-mm-Kreuzschlitzschrauben an den Außenseiten.

    • Zwei 10,5-mm-Kreuzschlitzschrauben in der Mitte.

    • Achte darauf, diese Schrauben nicht zu fest anzuziehen, wenn du das Gerät wieder zusammenbaust, sonst kann sich das Gehäuse verziehen.

  10. : Schritt 10, Bild 1 von 1
    • Entferne die beiden 5,2mm Kreuzschlitz #00 Schrauben von der Seite des Computers mit dem Optischen Laufwerk.

    • Es ist nicht notwendig, die entsprechenden Schrauben auf der anderen Seite des Computers zu entfernen.

  11. : Schritt 11, Bild 1 von 1
    • Starte in der Nähe des Bildschirms und arbeite dich sich zur Vorderseite des Computers vor, um das obere Gehäuse aufzuhebeln. Es wird mit Clips rechts über dem optischen Laufwerk gehalten. Diese lassen sich mit etwas festem Druck nach oben lösen.

    • Sei vorsichtig beim Aufhebeln der oberen Gehäuseeinheit. Es ist sehr leicht, sich eine Fingerkuppe aufzuschneiden und damit das Blutopfer zu bringen, das die Mac-Götter manchmal von denen verlangen, die darauf bestehen, ihre Reparaturen selbst durchzuführen.

    • Das obere Gehäuse ist über ein Trackpad und ein Tastaturband mit dem Logic Board verbunden, du darfst das obere Gehäuse also noch nicht ganz abziehen.

    • Wenn du Schwierigkeiten hast, die Clips zu lösen, achte darauf, dass du nicht aus Versehen den Kunststoffdeckel des oberen Gehäuses aus dem Metallrahmen löst.

  12. : Schritt 12, Bild 1 von 1
    • Haltedas obere Gehäuse hoch (von unten oder oben) und heble das orangefarbene Trackpad- und Tastaturkabel mit einem „Spudger“ aus seinem Anschluss.

    • Achtedarauf, zwischen der schwarzen Buchse und dem weißen Stecker zu hebeln. Möglicherweise musst du auf beiden Seiten hebeln, damit er sich richtig löst.

    • Heble nicht von unten oder oben, sondern von den Seiten.

    • Falls du das Kabel der oberen Gehäuseeinheit beim Versuch es zu entfernen beschädigst keine Panik! Wir bieten das Kabel auch einzeln an und es gibt auch eine Anleitung, die das ersetzen erleichtert.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 1
    • Use a spudger to disconnect the orange optical drive cable from the logic board.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 1
    • Use a spudger to disconnect the black fan connector from the logic board.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 1
    • Deroute the fan cable from behind the tab on the left side of the fan.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 1
    • Peel up the silver foil tape between the fan and the optical drive.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 1
    • Use a spudger to move the gray display data and black speaker cables to the right. This will reveal a silver screw securing the fan housing to the lower case.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 1
    • Remove the following 4 screws:

    • One 3 mm Phillips on the right side of the fan.

    • One 6 mm Phillips on the left side of the fan.

    • Two Phillips screws on the top left and bottom left of the fan.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 1
    • Push down on the left side of the fan and slide it slightly to the right in order to free the fan from the indicated tab on its right side. You can also use the tip of a spudger to free the tab on the right side of the fan.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 1
    • Lift the fan out of the computer, being careful not to rip the black felt tape.

    • When replacing an old fan, you may find a lot of dust in the vent and general area. A can of compressed air may be useful for cleaning it out before installing the new fan.

Ziellinie

188 weitere Nutzer:innen haben diese Anleitung absolviert.

iRobot

Mitglied seit: 09/24/09

1 Reputation

636 Anleitungen geschrieben

8 Kommentare

I am just extremely thankful for this great support guide material.

It was very clear to me. I shaped an empty cleenex tissue box, left only a little margin. I draw the bottom with a pen 24 squares numerating them from nr.1 to nr. 24, for the screw, one square for one set(or picture) of screw. I achieved to put the screw in exact order as I removed them, it went back, same screw into the same place. Not because I am that great, but because the guide is precise, and The Good Lord guided my hands to do this task with no errors.

The fan by the way was in perfect condition (late 2007 MB 3.1), almost no dust.

But it was a useful experience, for future possible issues.

lorinczistvan01 - Antwort

Having opened my MacBook several times before, fan replacement is one of the easier swaps to do. Tip: if your fan is running, but making upsetting noises, first check for a dust clog within the fan housing before you replace the fan. Lift the fan motor up without removing the felt tape seal, and inspect the heat sink grille for clogs (mine had a huge dust bunny on the left side, which was catching on the fan vanes). Carefully remove dust with spudger (or, ideally, a needle attachment on a 3M electronics vacuum). Good luck!

doctorvee - Antwort

I just completed this on my white macbook which I purchased in 2007. First, while in steps 19 and 20 they tell you to remove all four fan screws (two that hold the fan to it's lower housing, and two that hold the housing to the computer), they then only remove the fan without the housing. The entire housing should be removed in order to clean the heat sink behind the top of the fan. My replacement fan came as one unit anyway, so I replace the entire thing. Second, after many heating and cooling cycles, the black felt tape described in Step 20 was degraded and not able to be removed from the fan without ripping it. I replaced it with a couple layers of electrical tape (hopefully it holds up), but I would recommend getting the correct replacement tape before replacing the fan. Otherwise, if you're used to working on electronics and are relatively patient, it's actually pretty easy to do.

homebrew1099 - Antwort

Since this is a now 10 years old machine, don't get discouraged if you have some trouble with screws, specifically the longer screws in the upper case. I carried this machine with me everywhere for four years of college before retiring her, she's been twisted, dropped, sat on, etc. If your MacBook has been through what mine has you might run into the same issues. For me the top left screw sat below flush after being unscrewed and wouldn't pull up magnetically. I had to put light pressure on the case around the screw and use a pair of tweezers to grab the screw head and pull it out. Some gunk had built up at the bottom of the screw making it impossible to pull out magnetically. Be patient putting these upper case screws back in, over long periods slight deformations occur in the structure, so the screws won't line up quite as well as they used to. You shouldn't have to twist hard for the screws to go back in, try slightly pushing the bottom case up/down/left/right if you're having trouble. Great guide!

gingerichjared - Antwort

OMG I tore the fan connector out of the MB... The pads are all stuck to the connector... I barely used any force at all... Going to scrape the leads and attach wires now... :(

greenbubby - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 3

Letzte 7 Tage: 15

Letzte 30 Tage: 62

Insgesamt: 278,341