Zum Hauptinhalt wechseln


Folge dieser Anleitung, um einen schwächelnden Akku zu ersetzen. Wenn dein Akku aufgebläht ist, dann musst du entsprechende Vorsichtsmaßnahmen treffen.


  1. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen, Gehäuse-Unterseite: Schritt 1, Bild 1 von 1
    • Entferne die folgenden zehn Schrauben:

    • Drei 14,4 mm Kreuzschlitz #00 Schrauben

    • Drei 3,5 mm Kreuzschlitz #00 Schrauben

    • Vier 3,5 mm Kreuzschlitz #00 Ansatzschrauben

    • Wenn du die kleinen Schrauben wieder einsetzt, neige sie ein wenig, wie auch das Gehäuse geneigt ist (sie gehen nicht gerade hinein).

    How much weight can I save by removing the optical drive?

    gunes314 - Antwort

    You can save a lot of weight if lets say your installing a solid state drive or putting in a second hard drive but if you know that you use the CD/DVD disc drive a lot then you might just want to leave the drive alone.

    Marshall WahlstromHelgren -

    Tip: Use one of those weekday pill holders to have a cheep way to store screws you remove and each day of the week can be for different sizes or parts. It has been handy to have (much less expensive than the magnetic mat.

    Robert Wacker - Antwort

    Hello, where can I buy the screws I need in case I lose one of them?

    taylornya - Antwort

    I have one stripped screw... How opening without drill it?! Any suggestions please?

    rodrigosady - Antwort

    I also stripped a couple screws. I wasn’t able to open it up without drilling. After drilling the heads and removing the cover it was easy to hacksaw the tip and unscrew with a standard driver.

    Michael Wilkens -

    My top tip - make sure you buy good quality Phillips screwdrivers and a magnetic holder. Cheap screwdrivers won’t get the screws undone safely. Without a magnetic holder you have no chance of getting the tiny crews in and out safely.

    jeremyyoung - Antwort

    A good Phillips 00 is your friend here. Also, when reinserting the screws, gently start anticlockwise and you wil feel a click at the start of the thread. This tells you you’re in the right place and less likely to cross-thread through force in the wrong place.

    Iain Boyd - Antwort

    I feel like these are 000 screws. Amazon sales describe them as such and my 000 screwdriver fits better

    cam2000deluxe -

    Before ordering a new Trackpad remove the existing battery and try clicking the Trackpad. If it clicks OK with the battery out the source of problem is likely a swollen battery, which should to be replaced even if it still works to some degree. From the side of the battery you will likely see the soft part of the battery bulging beyond the hard case.

    Patrick Langvardt - Antwort

    That’s absolutely correct as I can testify. With the battery removed I also adjusted the T6 set screw that adjusts the sensitivity of the trackpad click, evidently someone had cranked mine down tighter than the factory setting.

    Gary Register -

    Le quatrième paragraphe dans les instructions en français n’est pas correct : ce ne sont pas les 2 petites vis, mais les 7 petites vis qui sont inclinées. Et les 3 grandes sont bien verticales.

    Degeorges - Antwort

    Bonjour ! Merci de votre observation. J’ai corrigé la traduction. iFixit étant un wiki, n’hésitez pas à modifiez si vous remarquez une erreur :) Encore merci de votre attention et à bientôt !

    Claire Miesch -

    Tip: if you have a magnetic screw mat or similar, lay the macbook over the mat to make sure it catches any screws that may decide to fall of and hide under your table

    Moritz - Antwort

  2. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen: Schritt 2, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen: Schritt 2, Bild 2 von 2
    • Löse mit den Fingern in der Nähe vom Ventilator die Gehäuse-Unterseite vom Hauptteil des Gehäuses.

    • Entferne die Gehäuse-Unterseite.

  3. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen, Akkuanschluss: Schritt 3, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen, Akkuanschluss: Schritt 3, Bild 2 von 2
    • Löse mit der Kante eines Spudgers den Akkuanschluss nach oben, weg vom Sockel auf dem Logic Board.

    • Es ist hilfreich, beide kurzen Seiten des Anschlusses gleichzeitig nach oben zu hebeln. Sei vorsichtig mit den Ecken des Anschlusses, da diese sehr leicht abbrechen können.

    Is this step of removing the battery connector required?

    manodh - Antwort

    yes - as with disassembly of any electronic component you have to remove any power source. You don't want to accidentally turn the Mac on

    khull -

    Prying the battery connector off does not take much force. I did exactly what the guide suggested (walked it off back and forth) with the spudger without any problems. Just be very gentle, much like with anything inside laptops, they are very fragile and need to be worked with carefully. A+ instructions, battery replacement was a success.

    aekinaka - Antwort

    Be patient on disconnecting this one. It worked for me step by step, little by little.

    Phil Wagner - Antwort

    I used the nails of thumb and pointer finger simultaneously - worked pretty fine

    Reinhard Kaune - Antwort

  4. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen: Schritt 4, Bild 1 von 1
    • Biege das Akkukabel vorsichtig weg vom Sockel des Logic Boards, damit es sich nicht aus Versehen beim Arbeiten wieder verbindet.

    I put some tape between the connector and socket while working on the drive.

    Stephen Smith - Antwort

    That's a good tip

    Anrothan -

    Great tip, I did that too

    Ahmed Mahran -

    One other note: The screw heads fit flush with the curvature of the case -- which means that they aren't exactly horizontal. In other words, they aren't perpendicular to the table that the computer is resting on. Don't try to force them straight in vertically, because you'll risk cross-threading them. (nearly ruined one screw hole myself!)

    lelandjordon - Antwort

    On my MacBook Pro, the connector seems to be an integral part of the battery.

    Jerry South - Antwort

    I suspect it’s just like the special screwdriver required for seatbelts on cars – to discourage regular consumers from attempting repairs. Of course, this only encourages consumers to use the wrong tool to attempt to repairs

    colleenthompson - Antwort

  5. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen, Akku: Schritt 5, Bild 1 von 1
    • Entferne die zwei folgenden Schrauben:

    • Eine 5,6 mm Tri-point Schraube

    • Eine 13 mm Tri-point Schraube

    Something isn’t right here. On my MacBook Pro, the connector is an integral part of the battery.

    Jerry South - Antwort

    Verify that this is the correct guide for your specific model—if not, we’ve got guides for all the other models, too.

    Jeff Suovanen -

    And which Apple “Genius” decided that a tri-wing screw would be just perfect for the job of holding the batter in place? Not smart for a genius.

    Jerry South - Antwort

    These tri-point screws are Y0 size. You’re welcome :)

    Rossi Macri - Antwort

    The 13 mm Tri-point screw was very tricky to screw back into place. I had to make several attempts, unscrewing and realigning the battery to get it right. The rest of this fix was very easy, but this one screw was the hardest part.

    Raymond Rinaldi - Antwort

    As per Rossi Macri’s comment, I also observed for step 5 that both screws are Tri-point Y0 for my MacBook Pro 13 inch mid-2012 model.

    telcik - Antwort

  6. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen: Schritt 6, Bild 1 von 1
    • Ziehe vorsichtig den Akku-Warnhinweis zwischen dem Akku und dem optischen Laufwerk von der Gehäuse-Oberseite.

    • Entferne den Warnhinweis nicht vom Akku.

    What is the reasoning behind not removing the label from the (old) battery?

    tom - Antwort

    Probably to help you remove it? Not sure, but I used it along with the clear tab to pull the battery out. Worked pretty good.

    aitorrecalde -

    One of the main thing is that it can weaken an already old battery which is never a good thing, especially if people try to remove the label using a pointy device and piercing the battery (can explode !). Also it is not useful to remove it and it allow tracking of old parts (recycle, dispose, …).

    Cajuteq -

  7. MacBook Pro (13 Zoll, Anfang 2011, Unibody)  Akku ersetzen: Schritt 7, Bild 1 von 1
    • Entferne den Akku durch Ziehen am Plastiketikett aus der Gehäuse-Oberseite.

    • Wenn du einen neuen Akku einbaust, solltest du ihn nach dem Einbau kalibrieren:

    • Lade ihn auf 100% und lasse ihn mindestens zwei weitere Stunden am Ladegerät. Ziehe den Stecker und benutze dein MacBook normal, um den Akku zu entladen. Wenn die Ladeanzeige am Minimum ist, dann speichere ab und lasse den Laptop an, bis er von selbst ausgeht. Warte wenigstens 5 Stunden und lade dann ohne Unterbrechung auf 100% auf.

    • Wenn dir nach der Installation deines neuen Akkus etwas Ungewöhnliches auffällt oder Probleme auftreten, kann es sein, dass du den SMC deines MacBooks zurücksetzen musst.

    My replacement battery came with a clear protective film that should be removed before installation. Be sure not to overlook the film on the bottom of the battery as it covers only a portion of that side and might be easy to overlook.

    Do not over-tighten the bolts holding the battery in place. One of the tabs on the original battery was broken, presumably due to over-tightening.

    Patrick Langvardt - Antwort

    The calibration suggestion given in this guide differs a bit from what iFIXIT sent with the battery. What came with the battery went like this…

    For optimal performance, calibrate your newly installed battery. Drain battery below 10%, then charge it uninterrupted to 100%.

    Daniel Lavelle - Antwort

    I recommend disregarding those instructions and following the steps in this article:

    1. Charge it to 100%, and keep charging it for at least two more hours.

    2. Unplug your laptop and use it normally to drain the battery.

    3. Save your work when you see the low battery warning.

    4. Keep your laptop on until it goes to sleep due to low battery.

    5. Wait at least five hours, then charge your laptop uninterrupted to 100%.

    Sam Omiotek -

    would it be dangerous to use the macbook without a battery in the meantime?

    724 F - Antwort

    It’s not dangerous (assuming you have put the back cover back on), though the computer will run slower. The charging assembly cannot supply as much amperage as the battery, so the processor will be throttled.

    Sam Omiotek -


Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

516 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de


Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Beginne zu übersetzen ›

12 Kommentare

Be careful with the four little "shouldered" screws on the bottom of the case towards the touchpad. They go back in at a slight angle. If you can't get the screws flush with the case, try tilting them a bit before screwing them in.

tim - Antwort

That was extremely helpful!

LeFixur -

Just replaced the battery of MacBook Pro Early 2011. Shipment was blazing fast. I ordered on Saturday and received the battery on Monday morning. It took me just 15 minutes with the right tools to change the battery. iFixit's step by step guide helped me to accomplish the task perfectly in the right way.

naveednajam - Antwort

I ordered a replacement battery from iFixit to squeeze some more life out of my early 2011 Macbook Pro. The new battery is great, my computer lasts way longer now which is super helpful. The guide helped me easily swap out the battery in less than 20 minutes. :)

Drew Dittmann - Antwort

I ordered a new battery and the required supplied to replace the batter in my early-2011 13" MacBook Pro. The process was extremely easy and took about 15-20 minutes. I was a little disappointed with the actual battery performance. Before replacing, my battery lasted about 30 minutes. Now it's about 2-2 1/2 hours. I was hoping the new battery replacement I purchased from them would have a longer life than 2 1/2 hours.

Cara Bunker - Antwort

I just wanted to thank the IFIXIT community for their contributions. I have an Early 2011 MacBookPro which I use for my photography editing. I am a Parochial school teacher and do a lot of the photography for the school. I use Pthotoshop and Lightroom, but since they are now subscription it is becoming cost ineffective. I was going to transfer over to OnOne 2018, but my MacBookPro is too old to use their product and I cannot afford to upgrade. When my trackpad started to fail (not click) I began to panic as I thought I was going to have to figure out a way to replace my laptop. Fortunately, IFIXIT showed me how to replace the battery for $90 and that fixed my trackpad. It did not fix my aging computer and OnOne 2018 issue, but it does allow me to work a bit longer without replacing my laptop.

I know this sounds like a sob story, but I know there are others out there in similar situations, thinking they have to replace their devices, but FIXIT may be able to extend the life of you machine.

Thank you again.

Kevin Gallagher - Antwort

Sadly I have to say I’m disappointed in the iFixit replacement battery. I was the big hope for my MacBook Pro (early 2011).

The installation worked fine and I was really happy…until I noticed drops in the “full charge”.

It just dropped from 30% to 10%.

Will analyse the current situation further… But it seems that I need a new MacBook soon…

Vanessa Haas - Antwort

Hi Vanessa, Sorry to hear of your purchasing experience. We’d like to assist! To avoid revealing personal information here on the guide page, please reach out to our Support team via help.ifixit.com so they can get you all squared away. Thanks!

Sam Goldheart -

Easy enough but my replacement battery ended up with the bloat and I had to put the old battery back in! If you end up with trackpad problems (especially on the left of the pad), double check your battery doesn’t have the bloat.

defunctzombie - Antwort

Thank you for the clear guide. I have also an early 2011 MacBookPro which suddenly had a bloated battery. I am not technical at all but managed to do it with the replacement battery and toolkit. Have to see how it keeps working in the future but for now all seems good. Thank you!

Ester van Dam - Antwort

This was my first repair on an apple product, guide was easy to follow, macbook pro works again!!

Mark Walker - Antwort

After being disappointed by not being able to get a replacement battery from Apple, I checked ifixit.com and found the kit with the battery and needed tools… awesome! The replacement process was easy, following their very clear instructions. After installation, I connected the laptop charger and it’s charging as it should. Looks like this was a great, economical fix for my father-in-law’s older Mac laptop! Thank You!!!

fredreichert5 - Antwort

Kommentar hinzufügen


Letzten 24 Stunden: 39

Letzten 7 Tage: 216

Letzten 30 Tage: 1,250

Insgesamt: 548,411