Zum Hauptinhalt wechseln

MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen

Was du brauchst

  1. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Unteres Gehäuse: Schritt 1, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Magnetic Project Mat
    $19.95
    Kaufen
    • Entferne die folgenden zehn Schrauben, mit denen das untere Gehäuse am oberen Gehäuse befestigt ist:

    • Zwei 2,3 mm P5 Pentalobe Schrauben

    • Acht 3,0 mm P5 Pentalobe Schrauben

    • Halte während der ganzen Reparatur deine Schrauben gut geordnet und achte darauf, dass sie genau an ihren alten Platz zurück kommen, sonst könnte dein Gerät beschädigt werden.

    If don’t have one of those neat project mats, then you can use small pieces of flattened blu-tack to hold the screws. If you arrange them in the shape of your mac book cover, and put the screws down methodically, you can get a one-to-one mapping of the screws to the correct screw holes.

    Toby Thurston - Antwort

    Or you can use an ice tray where you put the screws and the parts in separate bays in the same order as they come in the instructions.

    timofej.se -

    This is great! I used a small magnetic white board, and wrote on it to identify the parts as I went. This whole process, from the fast shipment to the great instructions to the complete, high quality, tool kit has been great. I’m typing this comment on my resurrected laptop. Thank you! Sue

    Susan Greer - Antwort

    It would be a good idea if people recorded in the comments which screws go where so that, if someone lost their screw positions, they could recover them from the comments.

    Raymond Shpeley - Antwort

  2. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 2, Bild 1 von 1
    • Versuche mit den Fingern zwischen das obere und das untere Gehäuse zu kommen.

    • Ziehe das untere Gehäuse behutsam vom Oberen weg.

    • Entferne das untere Gehäuse und lege es zur Seite.

  3. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 3, Bild 1 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 3, Bild 2 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 3, Bild 3 von 3
    • Drücke beim Wiederzusammenbau das untere Gehäuse in der Mitte leicht an, damit die beiden Plastikklammern wieder einrasten.

    • Das untere Gehäuse ist in der Mitte durch zwei Plastikklammern mit dem oberen Gehäuse verbunden.

  4. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Akkuanschluss: Schritt 4, Bild 1 von 1
    • Entferne die Plastikabdeckung über der Platine des Akkuanschlusses.

    The replacement cover doesn't seem to have the formed pads attached. I re-installed the original.

    Adrien - Antwort

  5. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 5, Bild 1 von 1
    • Entferne die folgenden Schrauben, mit denen die Platine des Akkuanschlusses am Logic Board befestigt ist:

    • Zwei 2,8 mm T6 Torx Schrauben

    • Eine 7,0 mm T6 Torx Paß-Schulterschraube

  6. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 6, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 6, Bild 2 von 2
    • Mit einer Pinzette kannst du die Plastikabdeckung rechts an der Platine des Akkuanschlusses entfernen.

    Is adhered to screw beneath, so lift firmly and slowly.

    Andrew - Antwort

    when doing this with metal tweezers as instructed in the video, it was difficult to get off and apparently while i was trying to do it, the tweezers went too far under and i believe made contact with the screw underneath? there was a zzz noise, an orange flicker and a little stream of smoke that came out. i freaked out and put everything back together to see if the laptop even still worked, it turned on and everything but died right away (i drained it before doing the repair anyway, so i was surprised it turned on at all).

    i finished the battery repair and did several other things while in there. i have charged it all the way as recommended and will use it later on to see how everything is, im hoping that it’s a okay, but could someone explain to me what happened and the possible consequences?

    Kait D - Antwort

  7. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 7, Bild 1 von 1
    • Entferne die 6,4 mm T6 Torx Breitkopfschraube, mit der die Platine des Akkuanschlusses am Logic Board befestigt ist.

    When reinstalling, be careful that the board lines up correctly and is completely seated in order for this screw to thread properly.

    Adrien - Antwort

  8. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 8, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 8, Bild 2 von 2
    • Ziehe die Platine des Akkuanschlusses vorsichtig vom Logic Board ab.

    • Es empfiehlt sich, die Batteriekabel nur leicht zu biegen, um die Platine über dem Logic Board und aus dem Weg zu halten.

    • Du solltest die Platine nicht vollständig umklappen oder gar die Kabel falten, denn dies könnte den Akku beschädigen.

  9. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Platine des Akkuanschlusses: Schritt 9, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Platine des Akkuanschlusses: Schritt 9, Bild 2 von 2
    • Schnapp dir den Interposer mit einer Pinzette.

    • Ein Interposer ist eine Schnittstelle, die eine elektrische Verbindung mit einer anderen verbindet. Bei dieser Reparatur ist es die Platine, die den Akku mit dem Logic Board verbindet.

    • Hebe den Interposer aus dem Logic Board heraus und entferne ihn.

    • Durch das Entfernen der Platine kannst du sicher gehen, dass der Akku während der Reparatur nicht mehr angeschlossen ist und so auch verhindern, dass der Computer versehentlich angeschaltet wird. Es ist auch deshalb eine gute Idee, die Platine herauszunehmen, weil sie sonst aus Versehen herausfallen könnte.

    How can I remove interposer I m not able to remove it

    Raunak - Antwort

    you must lift it absolutely vertically, or it fouls against the locator pin in the corner- you can easily get the impression that it won’t come over the end of this pin- almost like it’s rivetted in. it isn’t. get a good grip on it with the tweezers in the centre hole & one of the sides, & lift it STRAIGHT up.

    duncan rmi -

    I would recommend to use plastic tweezers in order to reduce risk of damage.

    Martin Sippel - Antwort

    Second that. If you have thin heat shrink tubing, form some over the tweezer tips. If the tubing is thin and small enough in diameter you’ll see the serrations of the tweezer tips.

    Raymond Shpeley -

    wat is the model this SSD

    thierry.wilow - Antwort

  10. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, iSight Kamerakabel: Schritt 10, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, iSight Kamerakabel: Schritt 10, Bild 2 von 2
    • Schiebe den Stecker am iSight Kamerakabel mit der Spudgerspitze aus seinem Anschluss auf dem Logic Board.

    • Es empfiehlt sich, vorsichtig abwechselnd auf beiden Seiten des Steckers zu drücken, um ihn so aus seinem Anschluss "herauswandern" zu lassen.

    This was the hardest part of the repair for me. The iSight cable was really lodged in its socket. "Walking" the connector as the guide suggests -- i.e. pushing on each side alternately at a 45 degree angle (with more force than I expected) -- eventually worked.

    Katherine Agnew - Antwort

  11. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 11, Bild 1 von 1
    • Schiebe das iSight Kamerakabel zur Seite.

  12. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, AirPort Karteneinheit: Schritt 12, Bild 1 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, AirPort Karteneinheit: Schritt 12, Bild 2 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, AirPort Karteneinheit: Schritt 12, Bild 3 von 3
    • Hebele die drei Antennenstecker mit dem flachen Ende des Spudgers hoch und entferne sie von der AirPort Karte.

    • Die drei Kabel sind mit schwarzen Hüllen in verschiedenen Längen markiert. Verbinde sie beim Zusammenbau folgendermaßen:

    • Das Kabel mit der langen Hülle mit dem Anschluss, der den Ports am nächsten ist

    • Das Kabel mit der kurzen Hülle mit dem Anschluss neben der Schraube

    • Das letzte Kabel hat keine Hülle und wird am letzten leeren Anschluss neben dem Lüfter eingesteckt.

    The long-sleeved and short-sleeved antenna cables are switched compared to this guide, on my Macbook Pro A1425. Maybe note which order they are in on your machine, since apparently they differ. http://i.imgur.com/r9g9ZXS.jpg

    Will Bradley - Antwort

    Be very careful with these, I wasn't and two of the cables detached from the connectors!!

    Felix Waller - Antwort

    Likewise, the antenna connectors on my Macbook A1425 Late 2012 Retina were not in the order as described in this guide. From the fan side the connectors should be - no sleeve, long sleeve, short sleeve

    smurad - Antwort

    As two other users have mentioned, the long-and short-sleeved cables for my late 2012/early 2013 A1425 were not in the order mentioned in the guide. If the laptop is positioned with fan in the upper left corner, the order (left to right) is short sleeve, long sleeve, no sleeve. If it is positioned as it is in the photo with the fan in the lower right, the order (left to right) is no sleeve, long sleeve, short sleeve.

    Katherine Agnew - Antwort

    I also found my cables were not as described in the guide. They were as @kagnew described.

    Daniel Revier - Antwort

  13. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 13, Bild 1 von 1
    • Schiebe die Antennenkabel zur Seite, so dass der Weg für die AirPort Karte frei wird.

    The display assembly has a metal retaining clip attached to the airport cables. I didn’t notice how this was positioned during disassembly, and it wasn’t mentioned in the guide. When I was reassembling the device, I found that it fit perfectly over the Torx T8 screws holding the display to the case. Attaching it here holds the airport cables nicely in place and out of the way.

    https://imgur.com/a/HK8mnOA

    bigfish333 - Antwort

  14. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Displayeinheit: Schritt 14, Bild 1 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Displayeinheit: Schritt 14, Bild 2 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen, Displayeinheit: Schritt 14, Bild 3 von 3
    • Fasse die schwarze Plastiklasche am Verschluss des Displaydatenkabels und klappe den Bügel in Richtung der Seite des Computers mit dem DC-In Anschluss.

    • Ziehe das Displaydatenkabel gerade aus seinem Anschluss auf dem Logic Board.

    • Ziehe das Displaydatenkabel nicht nach oben, da sein Anschluss sehr empfindlich ist. Ziehe das Kabel parallel zur Oberfläche des Logic Boards.

    Can this display fit in 13inch 2012 unibody?

    Bhavesh Hagwane - Antwort

  15. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 15, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 15, Bild 2 von 2
    • Hebe mit einer Pinzette die Gummiabdeckungen über dem rechten und linken Displayscharnier ab.

  16. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 16, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 16, Bild 2 von 2
    • Entferne die zwei 3,1 mm Torx T5 Schrauben, welche die Aluminiumhalterungen der Scharniere befestigen.

    I ended up stripping one of these out and had to use a T6 and some delicate pressure to get it out. Be careful.

    The T6 and a lot of downward pressure ended up doing the trick for me. YMMV

    Daniel Revier - Antwort

  17. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 17, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 17, Bild 2 von 2
    • Hebe mit einer Pinzette die Aluminiumhalterungen des linken und rechten Scharniers hoch.

  18. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 18, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 18, Bild 2 von 2
    • Entferne die vier inneren 5,3 mm Torx T8 Schrauben (zwei auf jeder Seite), welche das Display am oberen Gehäuse befestigen.

    There is a retainer for the airport cables that goes beneath the left and center screws.

    maccentric - Antwort

    My screws were covered with a thin tape, much like scotch tape. I used tweezers to remove it.

    Daniel Revier - Antwort

  19. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 19, Bild 1 von 2 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 19, Bild 2 von 2
    • Öffne das MacBook Pro etwa 110° und setze es seitlich auf dem Tisch, wie gezeigt, ab.

    • Halte das Display und das obere Gehäuse mit der linken Hand zusammen fest und entferne gleichzeitig die letzte T8 Torx Schraube von der oberen Displayhalteklammer.

    • Passe auf und halte Display und oberes Gehäuse mit der linken Hand gut zusammen. Wenn du dabei Fehler machst, dann kann das freie Display/obere Gehäuse herunterfallen, jedes der Bauteile könnte beschädigt werden.

    • Entferne die letzte Torx T8 Schraube, welche das Display noch am oberen Gehäuse befestigt.

  20. MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 20, Bild 1 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 20, Bild 2 von 3 MacBook Pro (13 Zoll, Anfang 2013, Retina Display) Displayeinheit austauschen: Schritt 20, Bild 3 von 3
    • Fasse beide Hälften des Gerätes, eine in jeder Hand.

    • Schiebe die untere Hälfte des Gerätes vorsichtig nach vorne, um es von der Displayeinheit zu trennen.

    • Lege jedes Teil vorsichtig zur Seite. Achte darauf, dass die untere Hälfte mit der Tastatur nach unten liegt.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

34 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Sam Goldheart

Mitglied seit: 10/18/12

465.238 Reputation

538 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.560 Anleitungen geschrieben

8 Kommentare

perfect tutorial! I fixed my screen completely destroyed falling down from my hands while a was falling asleep. Bought a new one on eBay (not original but perfect with the exception of the case slightly different in color and "texture".

Thanks iFix IT!

Ciao

Ciro

Ciro - Antwort

This walkthrough/guide is PERFECT! I barely tinker with electronics, but the high cost of repair made me want to try to install a new display assembly myself. Bless you, Sam Lionheart!

Virgil - Antwort

This worked really well. The only issue I had was uninstalling the camera. The instructions to pull the data display cable parallel to logic board made sense in step 14. Unfortunately I didn't understand the similarities in step 10. Is it possible to repair the camera now that the slot is completely broken?

D Sh - Antwort

Walk through worked perfect. Did it twice. The first time was just to make sure that wasn’t anything disconnect or any wires damage. The second time was to replace the screen. Works perfect.

Cody Milliron - Antwort

Hi,

can I replace an damaged display of a MacBook Pro 13” late 2013 with a display from the early 2013 version?

I compared the high-def pictures of each cable connection and they seem to be identical, or am I wrong?

Thanks for the help.

Cheers

L

Hans Wurst - Antwort

Hi there! Unfortunately as listed on the product page, the Late 2013 13” display is not compatible with the Early 2013, only the Mid 2014.

Sam Goldheart -

Can a late 2012 MacBook Pro 13” Retina display be used with an early 2013 MacBook Pro 13”?

Laurie Kirchmeier - Antwort

I really don’t know the answer, I am new to fixing EVERYTHING so my learning curve is steep. I successfully replaced my screen but I was careful to read what fit. It’s been awhile now. Good luck finding your answer

Karen Flowers -

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 12

Letzte 30 Tage: 72

Insgesamt: 55,730