Zum Hauptinhalt wechseln

MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen

Was du brauchst

  1. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen, Schrauben am Boden herausdrehen: Schritt 1, Bild 1 von 1
    • Entferne die folgenden 10 Kreuzschlitz-Schrauben, die die Gehäuse-Unterseite des MacBook Pro 13" Unibody befestigen:

    • Sieben 3 mm Schrauben.

    • Drei 13,5 mm Schrauben.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge - Antwort

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover - Antwort

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh - Antwort

    I use a magnetic mat and place the screws in order on that :)

    Cary B - Antwort

  2. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen, Bodenplatte abheben: Schritt 2, Bild 1 von 1
    • Hebe die Unterseite vorsichtig an und drücke sie Richtung Rückseite des Laptops, um die Halterungsclips zu lösen.

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike - Antwort

    Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.

    Well . . . I ain't never done nuttin' like that, before!

    Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.

    Am I allowed to cry?

    Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.


    kath myers - Antwort


    That was a brilliant read.

    Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.

    Glad your Mac repair journey worked out.


    Cary B -

  3. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen, Gummifüße: Schritt 3, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen, Gummifüße: Schritt 3, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen, Gummifüße: Schritt 3, Bild 3 von 3
    • Entferne alle gerissenen oder beschädigte Gummifüße.

    • Entferne alle Reste von Gummifüßen, die noch im Befestigungsloch stecken.

    • Entferne mit einer Pinzette alle Reste von altem Klebeband in der Klebefläche der Gummifüße.

  4. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 4, Bild 1 von 1
    • Reinige die Klebefläche mit Klebstoffentferner, um jegliche Reste des Klebers zu beseitigen.

    On my mid-2009 unibody MacBook Pro, there were thin, circular, black cloth pieces inside the case, covering the holes where the feet came through. I had to remove this tape, in order to push the feet through.

    Edward Horner - Antwort

  5. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 5, Bild 1 von 1
    • Wische mit einem alkoholbefeuchteten Tuch über die Klebefläche, um Reste vom Klebstoffentferner zu beseitigen.

  6. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 6, Bild 1 von 1
    • Ziehe die Schutzfolie vom Ersatzfuß ab.

  7. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 7, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 7, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 7, Bild 3 von 3
    • Platziere den neuen Fuß richtig in der Klebefläche.

    • Achte darauf, dass die kleine Passnoppe im Gummifuß in das entsprechende Loch nahe am Rand der Klebefläche eingreift.

    • Wenn der Fuß richtig sitzt, kannst du ihn nach unten drücken.

    • Schaue von der Innenseite des unteren Gehäuses, ob der Fuß gut ausgerichtet ist. Schiebe die Passnoppe mit einer Pinzette in das entsprechende Loch.

  8. MacBook Pro (13 Zoll, Mitte 2010, Unibody) Füße tauschen: Schritt 8, Bild 1 von 1
    • Drücke den neuen Fuß mit dem Finger fest und halte den Druck 30 Sekunden lang aufrecht, damit der druckempfindliche Kleber abbindet. Drücke von der anderen Seite dagegen.

    • Wiederhole die letzten sechs Schritte für jeden Gummifuß, der gerissen oder beschädigt ist.

    Support the rear feet from inside with your other hand before pressing down on new foot. Failure to do so may damage the plastic air grille inside the rear of the lower case. See the photos in step 3 above.

    hterlecki - Antwort

    My A1278 hasn't got holes in the backplate?

    The feet just seem to be stuck on with adhesive.

    Do I still have to unscrew the back?



    Rob Haygarth - Antwort

    Hi Rob,

    If the backplate doesn’t have the holes, you can still use the feet by just glueing them on. You would not have to open the backplate.

    Arthur Shi -

    I have been told that if you are using adhesive, you should follow these steps and remove the bottom.

    This way, adhesive doesn’t get inside the machine.

    Larry D Turner - Antwort

    Hi Larry,

    That is definitely true, if you are adding liquid adhesives. The feet we sell come with adhesive pre-installed on the feet. All you have to do is peel and stick!

    Arthur Shi -


Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

24 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de


Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Adam O'Camb

Mitglied seit: 04/11/15

181.278 Reputation

416 Anleitungen geschrieben

2 Kommentare

Just wondering if melting the original pads from inside the case with a flame would help to fix them in place for a little longer.

vlada - Antwort

I’d be a little wary of doing something like that. I don’t think it would help the pads stay in place very much, but it might make it really hard to clean the case when you do want to replace the pads. If you want to make the original pads last a little longer you can try pulling them off, cleaning off the old adhesive, and applying some new tape or glue.

Adam O'Camb -

Kommentar hinzufügen


Letzten 24 Stunden: 1

Letzten 7 Tage: 8

Letzten 30 Tage: 40

Insgesamt: 6,449