Zum Hauptinhalt wechseln

MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen

Was du brauchst

  1. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Schrauben am Boden herausdrehen: Schritt 1, Bild 1 von 1
    • Entferne die folgenden 10 Kreuzschlitz-Schrauben, die die Gehäuse-Unterseite des MacBook Pro 13" Unibody befestigen:

    • Sieben 3 mm Schrauben.

    • Drei 13,5 mm Schrauben.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge - Antwort

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover - Antwort

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh - Antwort

    I use a magnetic mat and place the screws in order on that :)

    Cary B - Antwort

  2. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Bodenplatte abheben: Schritt 2, Bild 1 von 1
    • Hebe die Unterseite vorsichtig an und drücke sie Richtung Rückseite des Laptops, um die Halterungsclips zu lösen.

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike - Antwort

    Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.

    Well . . . I ain't never done nuttin' like that, before!

    Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.

    Am I allowed to cry?

    Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.

    IFIXIT - IDIGIT!

    kath myers - Antwort

    HAHAHAHAHAHAHAHAHAHA.

    That was a brilliant read.

    Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.

    Glad your Mac repair journey worked out.

    :)

    Cary B -

  3. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Akku: Schritt 3, Bild 1 von 1
    • Wir empfehlen, vorsorglich den Akkuanschluss vom Logic Board zu lösen, um eine elektrische Entladung zu verhindern.

    • Löse mit der Kante eines Spudgers den Akkuanschluss nach oben, weg vom Sockel auf dem Logic Board.

    Zitat von gansodesoya:

    why is step 3 necessary?

    Just to disconnect any power source to avoid damages by short-circuits.

    MrKane - Antwort

    How do you get that battery connector back on? Do you just press it in back in place after you're done?

    Horace Chung - Antwort

    yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).

    maccentric -

    This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,

    Jeff Diamond - Antwort

  4. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Display: Schritt 4, Bild 1 von 1
    • Heble den Stecker des Subwoofers/rechten Lautsprechers mit dem flachen Ende des Spudgers aus seinem Anschluss auf dem Logic Board hoch.

    • Heble unter den Kabeln.

    Mine had a small piece of insulating material on top of the connector. By removing that first, I could then pry up the connector with less stress on the cable.

    istlota - Antwort

    Great tip! Thanks.

    juliet - Antwort

  5. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 5, Bild 1 von 1
    • Ziehe das Ende des Kamerakabels gerade aus seinem Anschluss heraus .

    • Achte darauf, dass du den Stecker parallel zur Oberfläche des Logic Boards zum optischen Laufwerk hin ziehst und nicht senkrecht vom Anschluss hoch.

  6. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 6, Bild 1 von 1
    • Fädle das Kamerakabel aus seinem Kanal im optischen Laufwerk heraus.

    for easy dismantle, just remove 2 screw of subwoofer

    Mohamad Faizal Sharudin - Antwort

  7. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 7, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 7, Bild 2 von 2
    • Entferne folgende Schrauben:

    • Zwei 10 mm Kreuzschlitzschrauben

    • Eine 3,8 mm Kreuzschlitzschraube

    • Ziehe die Kamerakabelhalterung unter dem Subwoofer vor und entferne sie vom Computer.

  8. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 8, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 8, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 8, Bild 3 von 3
    • Fasse die Plastikzuglasche an der Verriegelung des Displaydatenkabels und kippe sie nach oben über den Stecker in Richtung der Seite am Computer mit der Gleichstromversorgung (DC-in).

    • Ziehe das Displaydatenkabel gerade aus seinem Anschluss auf dem Logic Board heraus.

    • Achte darauf, dass du den Stecker direkt vom Anschluss weg und nicht senkrecht nach oben ziehst.

  9. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 9, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 9, Bild 2 von 2
    • Entferne die beiden Schrauben, mit denen der Halter des Displaydatenkabels am oberen Gehäuse befestigt ist:

    • Eine 8,6 mm Kreuzschlitzschraube

    • Eine 5,6 mm Kreuzschlitzschraube

    • Hebe den Halter des Displaydatenkabels aus dem oberen Gehäuse.

  10. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 10, Bild 1 von 1
    • Entferne, falls vorhanden, den kleinen Klebeschaumstreifen von den Displayschrauben nahe am Displaydatenkabel.

  11. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 11, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 11, Bild 2 von 2
    • Entferne die beiden äußeren 6,5 mm Torx T8 Schrauben, mit denen die beiden Displayhalterungen am oberen Gehäuse befestigt sind. (Also insgesamt vier Schrauben)

    You may have to lift/remove a foam tape on the left side as well

    Sebastien CHAPUIS - Antwort

  12. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 12, Bild 1 von 1
    • Öffne das MacBook Pro so, dass das Display rechtwinklig zum oberen Gehäuse steht.

    • Stelle das geöffnete Gerät wie gezeigt auf den Tisch.

    • Halte Display und oberes Gehäuse mit der linken Hand zusammen. Drehe dann die verbliebene Torx T8 Schraube aus der oberen Displayhalterung heraus.

  13. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 13, Bild 1 von 1
    • Achte darauf, das Display und das obere Gehäuse weiterhin mit der Hand zusammenzuhalten. Wenn du das nicht tust, kann das Display/obere Gehäuseteil herunterfallen und unter Umständen kann jede Komponente beschädigt werden.

    • Drehe die letzte verbliebene T8 Torx Schraube, die das Display noch am oberen Gehäuse befestigt, heraus.

    When reassembling, Careful not to drop your screw, or it may get stuck to the (magnetic) power adapter port. Oops!

    Save yourself some time and don't drop it!

    rowdyferret - Antwort

  14. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 14, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 14, Bild 2 von 2
    • Fasse das obere Gehäuseteil mit der rechten Hand und drehe es leicht in Richtung Oberkante des Displays. Dadurch löst sich die obere Displayhalterung von der Kante des oberen Gehäuses.

    • Drehe das Display leicht vom oberen Gehäuse weg.

    Make sure you make a 90 degree angle between the keyboard and the display before taking out the screws. If you have less than a 90, you will never get it apart due to the upper display bracket shape. It has to be at the right angle or it won't come out.

    mastover - Antwort

    I place it over keyboard side down hanging over a table. This way I know it's at 90 degrees and it also makes it easier to take it off.

    Nick - Antwort

  15. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 15, Bild 1 von 1
    • Hebe das Display hoch und vom oberen Gehäuse weg, achte dabei darauf, dass sich keine Halterungen oder Kabel verfangen.

    As mentioned in the previous step, place it keyboard side down with the edge hanging over a table. This way it's at 90 degrees and it makes it easier to align and get the screws in.

    Josh - Antwort

  16. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Displayglas: Schritt 16, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Displayglas: Schritt 16, Bild 2 von 2
    • In den folgenden Schritten wirst du mit einem Heißluftgebläse den Kleber aufweichen, mit dem der äußere schwarze Rand des Glases am Display befestigt ist. Der Bereich mit Kleber ist auf dem zweiten Bild rot markiert.

    • Fange in der rechten oberen Ecke mit dem Erwärmen des schwarzen Randes an. Stelle das Heißluftgebläse auf niedrige Stufe.

    • Richte die heiße Luft immer weg von der weichen Gummieinfassung um das Displayglas. Wenn du sie erwärmst, kann sie ein wenig schmelzen, so dass sie nicht mehr matt sondern glänzend aussieht. Wenn du sie berührst, kann sie dauerhaft verformt werden.

    • Durch die Wärmeeinwirkung kann sich eine Kondensationsschicht innen auf der Glasscheibe oder außen auf dem LCD bilden. Wenn die Glasscheibe vom Display getrennt ist, kann die Schicht mit Glasreiniger entfernt werden.

    Heating rubber strip it becomes glossy You can turn it to matte using ultrafine sandpaper (very ultrafine!!!) P2500

    Silvio - Antwort

    Great piece of advice. Thank you!

    Brian -

    With a lot of heating, for me, it was very hard to get the glass to separate from the case. I had better luck starting from the bottom right as I could grip better onto the case. Three mistakes I made:

    1. Once I got the glass separated, I probably didn't heat sufficiently as I was going around and the glass broke. That made the rest of the procedure miserable. Lesson: pull very gently.

    2. I must have touched one of the tiny bits of glass that fell on the LCD and it scratched the actual screen. :-(. Lesson: vacuum the pieces as you go and be very careful when touching the LCD.

    3. I somehow overheated the LCD screen at the top left and right corners and now the display is all wonky and faded at the corners. Not sure what the lesson is here.

    Athanassios Diacakis - Antwort

    First, if using a hair dryer, what setting should that be operated at? It would be much cooler than the heat gun, right?

    Second, the iFixit basic set comes with a small, clear suction cup. Would that be sufficient for this project, or does it require the stronger pull of the other cups?

    Finally, must I reapply adhesive to the case when replacing the glass? Does the original remain tacky and re-bond on assembly?

    contact - Antwort

    It's been a while since you asked, but since no one answered and someone else may have the same questions:

    Hair dryers vary a lot, depending on wattage. I would start on low or med, and work my way up to high if necessary. I'd keep the fan on the lowest setting.

    The little suction cup is for removing screens like the iMac, which just uses magnets, and possibly an iPad or iPhone. I would not want to use that for this project, get something about 2" wide with a decent handle.

    The screen should have the double sided glue tape already applied, just remove the backing. I wouldn't get glass that doesn't have the tape on it, big waste of time with little savings in cost.

    Jeff Kamis

    maccentric -

    All I can say for this is don't be tempted to hold the heat gun too close. I ended up burning my LCD the first time I did it and having to replace that when all I was looking to do was replace the cable. I got the glass off holding it about 4/5 inches from the screen and being patient (it took about 5/10 minutes in the end).

    Nick - Antwort

    The tape is very sticky and the glass is very fragile but at the same time fairly flexible.....I ended up breaking the glass ans it turned out to be a mess picking up the shards....but in the end a new glass is not too costly. the implication is that heating melts the glue but it is really just double stick tape.....there are some "youtube" videos that are worth a look but I would suggest using guitar picks and not a putty knife which creates a point load that breaks the glass....wear safety glasses!!

    brian62 - Antwort

    Be ready to replace the glass (good thing mine was already broken, I ordered one). Wear surgery gloves and protective glasses. Trust your nose, if it smell melted plastic, it’s a good clue to stop the heat.

    Sebastien CHAPUIS - Antwort

    It's more easy to do this step before removing the LCD. You have more control of the LCD and is more easy to remove the Glass.

    Felix - Antwort

    If you have a glass cover that is severely cracked then the heating gun and suction cup procedure really doesn’t work. Suction cups won’t hold and the already broken glass doesn’t lift. Here’s what I did that made the job easier. Using 2 inch wide transparent packing tape I laid it along the perimeter of the display but not covering the rubber edge. Then I used a 1/4 inch wood carving tool and very carefully removed the glass and 2 sided tape around the metal border. Use as your guide picture 2 in this step that shows where the camera and cable is located. Where the camera is located in the top center the 2 sided tape isn’t located so you can easily lift the glass. The camera cable runs up the right side in a trough in the metal border so when lifting the tape and glass in this area just keep the sharp end flat and it is wide enough it won’t dip into the trough and damage the cable. The tape was very helpful because it kept the glass from splintering and going everywhere.

    joe lochner - Antwort

  17. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 17, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 17, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 17, Bild 3 von 3
    In diesem Schritt verwendetes Werkzeug:
    Heavy-Duty Suction Cups (Pair)
    $14.95
    Kaufen
    • Wenn die Scheibe warm genug ist, befestige einen kräftigen Saugheber in der rechten oberen Ecke der Glasscheibe.

    • Befestige den Saugheber nicht auf der Gummieinfassung an der Kante der Glasscheibe.

    • Um unseren Saugheber zu befestigen, bringe ihn zuerst mit dem beweglichen Griff parallel zur Glasscheibe an. Drücke den Saugheber leicht gegen das Glas und kippe den beweglichen Griff, bis er parallel zum anderen steht.

    • Ziehe die Ecke des Displayglases langsam und vorsichtig von der Displayeinheit hoch.

    • Wenn - wie im dritten Bild zu sehen - sich nur die Oberkante der Glasscheibe anhebt, dann wiederhole Schritt 1 und 2, bis du die Ecke des Displays anheben kannst.

  18. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 18, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 18, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 18, Bild 3 von 3
    • Hebe die Ecke des Displayglases behutsam so hoch, dass du einen Spudger zwischen ihm und der Displayeinheit einsetzen kannst.

    • Heble das Displayglas vorsichtig mit dem Spudger aus der Klebeverbindung zum Display hoch.

    • Heble die Glasscheibe einige Zentimeter von der oberen rechten Ecke aus entlang der oberen und rechten Kante hoch.

  19. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 19, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 19, Bild 2 von 2
    • Erwärme mit dem Heißluftgebläse den Kleber unter dem schwarzen Streifen am rechten Rand der vorderen Glasscheibe.

    • Bringe einen Saugheber an der rechten Seite der vorderen Glasscheibe an.

    • Ziehe die Glasscheibe hoch und trenne sie gleichzeitig mit dem flachen Ende des Spudgers von der Displayeinheit ab.

    • Arbeite so lange weiter, bis der rechte Rand der Glasscheibe komplett vom Display abgelöst ist.

    • Es kann hilfreich sein, wenn du mit einem Plektrum oder einem anderen flachen Werkzeug verhinderst, das sich die obere rechte Ecke wieder am Display festklebt.

    I ended up breaking my glass panel due to using the spudger. I think if you use something more like a small putty knife you will do better. The spudger puts a lot of pressure in a small spot while the putty knife would put a little pressure over a larger area. Also, if you do break the glass, be sure to get ALL of the broken bits off before putting the new one on. Also, watch out for those broken bits as they tend to penetrate skin quite easily, and stay there for days!

    mastover - Antwort

  20. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 20, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 20, Bild 2 von 2
    • Erwärme mit dem Heißluftgebläse den Kleber unter dem schwarzen Streifen am oberen Rand der vorderen Glasscheibe.

    • Bringe einen Saugheber am oberen Rand der vorderen Glasscheibe an und ziehe die Glasscheibe vom Display weg.

    • Arbeite weiter sorgfältig am oberen Rand entlang, wobei du beim Auftrennen des Klebers mit dem flachen Ende des Spudgers nachhelfen kannst.

  21. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 21, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 21, Bild 2 von 2
    • Erwärme mit dem Heißluftgebläse den Kleber unter dem schwarzen Streifen um die obere linke Ecke der vorderen Glasscheibe.

    • Bringe einen Saugheber in der oberen linken Ecke der vorderen Glasscheibe an.

    • Ziehe am Saugheber und heble vorsichtig mit dem flachen Ende des Spudgers die Glasscheibe aus der Displayeinheit heraus.

    • Wenn du die obere linke Ecke abgelöst hast, kann es hilfreich sein, mit einem Plektrum oder einem anderen flachen Werkzeug zu verhindern, dass sich die Glasscheibe wieder mit der Displayeinheit verklebt.

  22. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 22, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 22, Bild 2 von 2
    • Benutze einen Haartrockner oder ein Heißluftgebläse, um den Kleber unter dem schwarzen Streifen an der linken Seite der Glasscheibe aufzuweichen.

    • Bringe einen Saugheber an der linken Seite der vorderen Glasscheibe an.

    • Ziehe die vordere Glasscheibe hoch und trenne sie gleichzeitig mit dem flachen Ende des Spudgers von der restlichen Displayeinheit ab.

    • Setze die Arbeit an der linken Kante des vorderen Displayglases fort, bis sie ganz vom Display abgelöst ist.

  23. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 23, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 23, Bild 2 von 2
    • Nachdem nun die obere, rechte und linke Kante der Glasscheibe abgelöst sind, kannst du die Oberkante der Glasscheibe langsam anheben und vom Display wegdrehen.

    • Befreie, wenn nötig, die Unterkante der Glasscheibe mit dem flachen Ende des Spudgers aus der Klebeverbindung zur Displayeinheit.

    • Bevor du die Glasscheibe wieder befestigst, musst du die Innenseite de Glasscheibe und das LCD erst gut reinigen. Fingerabdrücke oder eingeschlossene Staubkörnchen sind später sehr störend sichtbar.

  24. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 24, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 24, Bild 2 von 2
    • Überspringe diesen Schritt, wenn du die ursprüngliche Glasscheibe wieder einbaust.

    • Setze ein Plastiköffnungswerkzeug zwischen Glasscheibe und Kamerahalterung ein und schiebe es um die Kamerahalterung herum, bis sie sich ablöst.

    • Vergiss beim Zusammenbau nicht, die Kamerahalterung an der neuen Glasscheibe festzukleben.

  25. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 25, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 25, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 25, Bild 3 von 3
    • Beim Ausbau der Glasscheibe kann das Kamerakabel an der Glasscheibe kleben bleiben, so dass es beim Abheben der Scheibe von der Kameraplatine abgetrennt wird. Wenn das Kamerakabel bei dir noch angeschlossen ist, kannst du diesen Schritt überspringen.

    • Bevor du das Kabel wieder anschließen kannst, musst du erst das Stück Klebeschaumstoff über dem ZIF-Verbinder des Kamerakabels mit der Spudgerspitze ablösen.

    • Klappe den Sicherungsbügel am ZIF-Verbinder des Kamerakabels mit der Spudgerspitze hoch.

    • Schiebe das Kamerakabel in seinen Anschluss auf der Kameraplatine hinein und klappe den Sicherungsbügel mit der Spudgerspitze herunter, so dass das Kabel wieder gut im ZIF-Verbinder gesichert ist.

    • Klebe das Stück Schaumstoff wieder am Anschluss des Kamerakabels fest.

  26. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Verschlussabdeckung: Schritt 26, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, Verschlussabdeckung: Schritt 26, Bild 2 von 2
    • Schiebe die Verschlussabdeckung zur rechten Displayseite.

    • Sie sollte sich etwa 7 mm nach rechts bewegen lassen und dann stoppen. Zwinge sie nicht über diesen Punkt hinaus.

    • Achte beim Zusammenbau darauf, dass du sie ungefähr 7 mm weiter rechts als in der endgültigen Position am Display über die Teile hinweg schiebst, die an der Unterkante des Displays vorstehen.

    The plastic tabs of the clutch fit into slots that end up holding the clutch in place. The idea is that you need to slide the clutch to the right to free the plastic tabs from the metal slots in the LCD frame.....then you can separate the clutch from the frame.

    brian62 - Antwort

  27. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 27, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 27, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 27, Bild 3 von 3
    • Beginne ganz rechts und rüttle die Verschlussabdeckung vorsichtig auf ihrer langen Achse vor und zurück und ziehe sie dabei vom Display weg.

    • Arbeite von rechts nach links und löse die Abdeckung behutsam aus der Unterkante der Displayeinheit heraus.

    • Hebe die Verschlussabdeckung von der Frontblende hoch und lege sie zur Seite.

    • Achte beim Anbringen der Verschlussabdeckung darauf, dass du die Öffnung aufweitest, wenn du sie über die kleine schwarze Zierabdeckung ziehst, die das offene Ende der Verschlussabdeckung verdeckt, wenn sie fertig angebracht ist. Die Zierabdeckung hat empfindliche kleine Befestigungsarme, mit denen sie im rechten Scharnier befestigt ist.

    Highly recommended to remove clutch cover BEFORE heating up glass, because cover is made of very thin plastic and it'll be deformed!

    Basically, I'm removing everything from screen - clutch cover, wifi card, antenna, all plastic bits, and only then proceed with heating and glass removal.

    DigiHead - Antwort

    Starting at it's far LEFT end

    Job - Antwort

    just slide the plastic cover to the right and it comes right off.

    William - Antwort

  28. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen, LCD: Schritt 28, Bild 1 von 1
    • Hole das Displaydatenkabel aus seiner Halterung nahe an der linken unteren Displaykante heraus.

  29. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 29, Bild 1 von 1
    • Entferne folgende sechs Schrauben, mit denen das LCD an der Frontblende befestigt ist:

    • Vier 3,25 mm Kreuzschlitzschrauben mit großen Köpfen.

    • Zwei 3,2 mm Kreuzschlitzschrauben mit kleinen Köpfen.

  30. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 30, Bild 1 von 1
    • Versuche noch nicht, das LCD zu entfernen. Die Leitungen entlang der Unterkante sind noch in einem Spalt in der Einlassung für das LCD in der Aluminium-Displayeinheit eingezwängt.

    • Halte das Display senkrecht und neige es soweit, bis du die Oberkante des Displays fassen kannst. Drehe es dann leicht aus der Displayeinheit heraus, achte dabei darauf, dass die Leitungen nicht aus der Unterkante herausbrechen.

  31. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 31, Bild 1 von 1
    • Ziehe das LCD zum oberen Rand des Displays hin, so dass die Leitungen an der Unterkante aus der Einlassung in der Aluminium- Displayeinheit herausgleiten.

    • Es hilft, wenn du das Displaydatenkabel mit einer Hand durch seinen Kanal in der Aluminium-Displayeinheit führst, während du das LCD mit der anderen Hand zum oberen Rand des Displays ziehst.

  32. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 32, Bild 1 von 1
    • Ziehe das Stück Klebeband vom Stecker des Displaydatenkabels von der Kante des LCDs her ab.

  33. MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 33, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) LCD tauschen: Schritt 33, Bild 2 von 2
    • Klappe den dünnen Metallhalter hoch, mit dem das Displaydatenkabel in seinem Anschluss auf dem LCD gesichert ist.

    • Ziehe das Displaydatenkabel gerade von seinem Anschluss auf dem LCD weg.

    • Hebe das LCD von der Displayeinheit weg und lege es zur Seite.

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

77 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

5 Kommentare

All I can say is THANKS! I was able to replace my daughters display, the bottom aluminum panel and to remove the dents from the top aluminum panel. Without your guide, I doubt I ever could have done this. You saved me hundreds! Your spudger tool was worth its weight in gold....till I used it to break the glass front panel...sigh. Still, I'll use that hundreds of times from now on.

mastover - Antwort

==Step 17==

It is extremely critical that when attaching the suction cup to FIRST LIFT THE LEVER ABOUT HALF WAY before attaching to the glass in order to only apply about half the suction the tool is capable of applying!! Lift the lever half way. Set into position on glass. Lift the rest of the way to apply about half of the suction cup's potential suction. Failure to do this WILL result in circular break around the suction cup!

jnserr - Antwort

This was extremely helpful. I am a junior in high school who was issued a Mac for class. I am one of those anti-Apple people, so I get easily frustrated with them and tend to beat them up a bit. Consequently, I broke it. Being low on funds, I couldn't afford the repair costs, let alone had the nerve to own up to my actions and tell the teacher about it. SO....after staying up an extra couple hours researching the problem, I discovered this and decided to give it a try. Despite already being somewhat tech savvy, I found this resource very helpful, even more so after re-reading it and watching a couple how-to videos. The problem was fixed in no time.

Lets just say, thanks to this site, the school never found out that I broke the laptop. :)

Alexander - Antwort

GREAT GUIDE! Thanks!

I had a laser targeted infrared thermometer for another project ($25 at local hardware store) and found the screen cover adhesive softened nicely at top and sides at 140-145F. I used a hairdryer on high setting.

I found with the top edge and both side edges lifted free of the adhesive in earlier stages, the bottom edge lifted easily at 100-105F. (I had package taped the screen as it had cracks, being sure the tape laid flat so sunction would form in the early steps.

NOTE THE MAXIMUM SPECiIFIED NONOPERATING TEMPERATURE IS LISTED BY APPLE AT 113F for the 2010 MBP 13”. Separating the bottom and top cases allows the keyboard and all the other goodies in the lower case to rest comfortably away from the heat.

One or two very thin flexible pry tools like iSesame (inexpensive online) worked well once the upper corner was lifted with a suction cup

Stan Wingate - Antwort

This guide is the same of MacBook Pro 13 unibody 2012?

Ruben Costa - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 4

Letzte 7 Tage: 47

Letzte 30 Tage: 205

Insgesamt: 160,029