Zum Hauptinhalt wechseln

MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen

Was du brauchst

  1. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Schrauben am Boden herausdrehen: Schritt 1, Bild 1 von 1
    • Entferne die folgenden 10 Kreuzschlitz-Schrauben, die die Gehäuse-Unterseite des MacBook Pro 13" Unibody befestigen:

    • Sieben 3 mm Schrauben.

    • Drei 13,5 mm Schrauben.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge - Antwort

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover - Antwort

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh - Antwort

    I use a magnetic mat and place the screws in order on that :)

    Cary B - Antwort

  2. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Bodenplatte abheben: Schritt 2, Bild 1 von 1
    • Hebe die Unterseite vorsichtig an und drücke sie Richtung Rückseite des Laptops, um die Halterungsclips zu lösen.

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike - Antwort

    Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.

    Well . . . I ain't never done nuttin' like that, before!

    Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.

    Am I allowed to cry?

    Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.

    IFIXIT - IDIGIT!

    kath myers - Antwort

    HAHAHAHAHAHAHAHAHAHA.

    That was a brilliant read.

    Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.

    Glad your Mac repair journey worked out.

    :)

    Cary B -

  3. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Akku: Schritt 3, Bild 1 von 1
    • Wir empfehlen, vorsorglich den Akkuanschluss vom Logic Board zu lösen, um eine elektrische Entladung zu verhindern.

    • Löse mit der Kante eines Spudgers den Akkuanschluss nach oben, weg vom Sockel auf dem Logic Board.

    Zitat von gansodesoya:

    why is step 3 necessary?

    Just to disconnect any power source to avoid damages by short-circuits.

    MrKane - Antwort

    How do you get that battery connector back on? Do you just press it in back in place after you're done?

    Horace Chung - Antwort

    yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).

    maccentric -

    This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,

    Jeff Diamond - Antwort

  4. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Ventilator: Schritt 4, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Ventilator: Schritt 4, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Ventilator: Schritt 4, Bild 3 von 3
    • Benutze einen Spudger um den Verbinder des Ventilatorkabels aus seinem Anschluss auf der Hauptplatine zu lösen.

    • Am Besten geht das, indem du den Spudger in seiner Längsachse verdrehst während du ihn unter den Ventilatorkabeln ansetzt, um den Verbinder zu lösen.

    • Im zweiten und dritten Bild siehst du den Verbinder und den Anschluss des Ventilators. Passe auf, dass du den Plastikanschluss nicht aus der Hauptplatine herausbrichst, wenn du das Kabel herauslöst. Die Hauptplatine sieht in deinem Gerät vielleicht ein kleines bisschen anders aus, als auf dem zweiten Foto, aber der Ventilatoranschluss ist gleich.

    The image is very misleading. This is why many people are breaking their connectors. Please correct this and make it VERY clear that one has to put the spudger straight behind the cables, NOT behind the connector, as shown in the pic.

    Giunia - Antwort

    Thankfully there is a helpful guide in the comments on this post for fixing the socket in the likely event that you snap the sucker clean off like I did:

    I popped off the fan connection from the logic board...Fix?

    agoodcourage - Antwort

    As Giunia said I too just broke the connector only because the photo shows to slide a spudger between the connector socket and the motherboard. I am now out of my only computer. This is VERY frustrating.

    Nha1234 - Antwort

    Broke it as well the picture is very misleading.

    Christian Flores - Antwort

    Local mobile repair shop soldered it back for me.. but it cost me twice as much as fan I ordered from china. They told me to use two tools in the future.. one to keep the edge down and other to gauge gently from under the cables...

    Bade -

  5. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 5, Bild 1 von 1
    • Löse die folgenden drei Schrauben:

    • Eine 7 mm Torx T6 Schraube

    • Zwei 5,4 mm Torx T6Schrauben

  6. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 6, Bild 1 von 1
    • Hebe den Ventilator aus dem oberen Gehäuse.

  7. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Logic Board: Schritt 7, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Logic Board: Schritt 7, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Logic Board: Schritt 7, Bild 3 von 3
    • Fasse die Zuglasche am Sicherungsbügel des Display-Datenkabels an und drehe es in Richtung der Seite mit DC-in Buchse.

    • Ziehe den Verbinder des Display-Datenkabels vorsichtig direkt aus seinem Sockel heraus, parallel zum Logic Board.

    • Ziehe das Kabel nicht nach oben, damit könntest den Anschluss kaputt machen.

    On my system the pad on top of the connector was shifted making the bracket difficult to rotate into the up position. The bracket looks like a handle so my first instinct was to pull it straight up. Big mistake. I ended up popping the brass guard off the connector on the logic board. The instructions could benefit from an arrow indicating the direction to pull and rotation of the bracket.

    highnoontoday - Antwort

  8. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 8, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 8, Bild 2 von 2
    • Drehe folgende Kreuzschlitzschrauben heraus, die die Befestigungsklammer des Display-Datenkabels am Gehäuse sichern:

    • Eine 8,6 mm Kreuzschlitzschraube

    • Eine 5,6 mm Kreuzschlitzschraube

    • Hebe die Klammer des Display-Datenkabels aus dem Gehäuse.

  9. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 9, Bild 1 von 1
    • Heble die Verbinder vom Subwoofer und rechten Lautsprecher mit dem flachen Ende eines Spudgers vom Logic Board.

    Push it straight down. It should snap in.

    BobG - Antwort

    The first time i tried this on a MBP 13 I broke the connector form the board. It should be noted that you have to be very careful in this step, as the plug fits very tightly and you can easily use too much force to tear the connector from the board. Use a second spudger to hold down the connector at its border and try very gently using a second spudger to move the plug out of the connector upwards.

    Joachim Kathmann - Antwort

  10. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 10, Bild 1 von 1
    • Ziehe den Stecker des Kamerakabels in die Richtung des optischen Laufwerks, um es vom Logic Board zu trennen.

    • Dieser Anschluss ist aus Metall und verbiegt sich leicht. Achte darauf, den Stecker und den Anschluss auf dem Logic Board zueinander auszurichten, bevor du die beiden Teile miteinander verbindest.

    As mentioned, the socket can be easily damaged when re-inserting it. I didn't care enough and one pin was damaged. Wifi was not detected.

    Hopefully the pin was not broken (only bent). Putting it back in its correct position, the wifi re-appeared.

    Arnaud ROSAY - Antwort

  11. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 11, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 11, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 11, Bild 3 von 3
    • Heble die Verbinder vom optischen Laufwerk, von der Festplatte und vom Trackpad mit dem flachen Ende eines Spudgers vom Logic Board.

  12. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 12, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 12, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 12, Bild 3 von 3
    • Hebe die Sicherungsklappe am ZIF-Verbinder für das Flachbandkabel der Tastatur mit dem Fingernagel oder einer Spudgerspitze hoch.

    • Schiebe dann mit dem Spudger das Flachbandkabel der Tastatur aus dem Sockel.

    Sometimes spulger is not the best tool to slide the cable out. If it is difficult to slide, try two toothpicks to pull the cable from two sides simultaneosly.

    Leo Nikitin - Antwort

    Toothpicks did the trick, thanks

    Gábor SEBESTYÉN -

    As Mateo said, replacing the zif cable is NOT easy, and in this case, will leave you with a computer that won't power on- this cable connects the power button. I learned a trick somewhere for dealing with these cables- put a piece of good sticky tape on the cable, and use it to pull it back into the connector. Works every time.

    stevesontheroad - Antwort

    Yeah! The tape trick worked for me. Thanks!

    Ted Bishop -

    Thank you Steve, it’s works perfectly.

    never_forever18 -

  13. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 13, Bild 1 von 1
    • Ziehe das kleine Stück schwarzes Band vom Sockel des Flachbandkabels der Tastaturbeleuchtung ab.

    Be very careful while taking this black tape off. I accidentally broke the chip off the motherboard and so my keyboard is not backlit any more.

    Asim Akath - Antwort

  14. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 14, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 14, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 14, Bild 3 von 3
    • Hebe die Sicherungsklappe am ZIF-Verbinder für das Flachbandkabel der Tastaturbeleuchtung mit der Spudgerspitze hoch.

    • Schiebe dann mit dem Spudger das Flachbandkabel der Tastaturbeleuchtung aus dem Sockel.

    Be especially careful as my hole socket detached from the board. It would have helped to vertically press the socket to the board with the tip of a spudger. Thus partially blocking the strap, you can first peel the free end, then change position and peel the rest. Slide the ribbon cable perfectly horizontally.

    Rainer - Antwort

    I had the same issue of trying to get the ZIF cable back in but found that if I used a piece of scotch tape, it worked. I followed this guide. MacBook unibody keyboard ribbon cable won't go in

    spearson - Antwort

    A reassembly trick that works for me is to use some 3/4" blue painters tape to stick to the very back (lower end) of the ribbon cable so I can pull it up and back before locking the cam. Trying to get a good grip without cutting, or crimping the ribbon means no tweezers or pliers can be used.

    originalmachead - Antwort

  15. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 15, Bild 1 von 1
    • Heble den Verbinder des Kabels der Akkuanzeige mit dem flachen Ende des Spudgers aus dem Logic Board.

    If you’re swapping top cases, you might need to remove the battery indicator from the case and swap it to the replacement top case. It attaches with three very tiny Phillips screws. I wasn’t aware that my replacement top case didn’t have this part and got confused when reversing the steps to reassemble and I didn’t have this connector. I had to take the battery back out in order to swap the indicator over.

    Mark Barnes - Antwort

    Interesting this guide doesn’t have you disconnect the battery after step 2 then shows it unplugged already in step 14.

    plink53 - Antwort

    I would recommend revision to this guide to put battery disconnection as the first step after opening the bottom case. First rule of logic/mother boards: don’t work on or around if power is applied.

    dsfeehan - Antwort

  16. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 16, Bild 1 von 1
    • Löse die Klebeverbindung des Mikrofons am oberen Gehäuse mit der Spudgerspitze.

    on the Australian/Asia version speaker cable is located underneath the logic board.

    linuxuser101 - Antwort

    Norwegian/European versjon too. Recommend using a pincer to lift it up.

    Note you’re not supposed to only remove the rubber, in fact that should stay on

    eisa01 - Antwort

  17. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 17, Bild 1 von 1
    • Entferne folgende Torx-Schrauben:

    • Zwei 7mm T6 Torx Schrauben an der DC-in Platine.

    • Fünf 3,3 mm T6 Torx Schrauben

    • Zwei 4 mm T6 Schrauben

  18. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 18, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 18, Bild 2 von 2
    • Es ist nicht zwingend nötig den Akku zu entfernen, bevor du das Logic Board heraushebst. Es ist aber sicherer und einfacher. Wenn du den Akku drinnen lässt, achte sehr darauf, dass du das Logic Board nicht am Akku in der Nähe des Strichcodes verbiegst.

    • Entferne folgende TriPoint Schrauben, die den Akku am oberen Gehäuse befestigen:

    • Eine 5,5 mm TriPoint Schraube

    • Eine 13,5 mm TriPoint Schraube

    • Hebe den Akku aus dem Gehäuse.

  19. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 19, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 19, Bild 2 von 2
    • Hebe das Logic Board am linken Rand hoch, bis die Ports aus der Seite des oberen Gehäuses frei werden.

    • Ziehe das Logic Board von der Seite des Gehäuses weg, achte dabei darauf, dass sich die DC-in Platine nicht verfängt.

    Be careful while taking the board out, as the heatsink usually is caught by the optic drive.

    Leo Nikitin - Antwort

    mid 2012: Careful of the left speaker (on your right because unit is upside down). Gently remove with spudger tool before removing logic board and when reinstalling press firmly back into place with spudger. Install speaker after putting logic board in place but before installing screws.

    JASON CULP - Antwort

    Step 18 is out of order. Steps following this show it still installed, which is confusing.

    plink53 - Antwort

  20. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Oberes Gehäuse: Schritt 20, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Oberes Gehäuse: Schritt 20, Bild 2 von 2
    • Entferne die beiden Kreuzschlitzschrauben, mit denen die Festplattenhalterung am oberen Gehäuse befestigt ist.

    • Die Schrauben bleiben in der Halterung hängen.

    • Hebe die Halterung aus dem oberen Gehäuse heraus.

  21. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 21, Bild 1 von 1
    • Hebe die Festplatte an der freien Kante hoch und ziehe sie aus dem Gehäuse heraus, achte dabei auf die Kabel, mit denen sie am Computer angeschlossen ist.

  22. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 22, Bild 1 von 1
    • Ziehe den Festplattenstecker vom Laufwerk ab.

  23. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 23, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 23, Bild 2 von 2
    • Entferne folgende vier Schrauben, mit denen die Festplatte und das Kabel des Infrarotsensors am oberen Gehäuse befestigt sind:

    • Zwei 1,5 mm Kreuzschlitzschrauben

    • Zwei 4 mm Kreuzschlitzschrauben

    • Schiebe die Halterung der Festplatte und die Halterung des Infrarotsensors vom Rand des oberen Gehäuses weg.

    • Löse vorsichtig das Kabel der Festplatte und des Infrarotsensors vom oberen Gehäuse ab.

    The orange-highlighted screws here are far longer than 4mm, aren't they?

    Shelley - Antwort

  24. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 24, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 24, Bild 2 von 2
    • Entferne folgende Schrauben, mit denen der Subwoofer am oberen Gehäuse befestigt ist:

    • Eine 3,8 mm Kreuzschlitzschraube

    • Eine 5 mm Kreuzschlitzschraube

    • Der Subwoofer ist immer noch am rechten Lautsprecher angeschlossen, entferne ihn also noch nicht ganz.

    • Hebe den Subwoofer vom optischen Laufwerk weg und lege ihn auf dem Computer ab.

  25. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 25, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 25, Bild 2 von 2
    • Entferne die beiden Kreuzschlitzschrauben, mit denen die Halterung des Kamerakabels am oberen Gehäuse befestigt ist.

    • Es kann sein, dass die linke Schraube im Kamerakabel hängen bleibt.

    • Hebe die Halterung des Kamerakabels aus dem oberen Gehäuse heraus.

  26. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 26, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 26, Bild 2 von 2
    • Entferne die drei 2,5 mm Kreuzschlitzschrauben, mit denen das optische Laufwerk am oberen Gehäuse befestigt ist.

    • Hebe das optische Laufwerk am linken Rand an und ziehe es aus dem Computer heraus.

  27. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 27, Bild 1 von 1
    • Ziehe das kleine schwarze Stückchen Klebeband vom Kabel des rechten Lautsprechers ab.

    • Sei vorsichtig, direkt unter diesem Klebeband befindet sich das Flachbandkabel zur Einschalttaste.

  28. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 28, Bild 1 von 1
    • Heble den rechten Lautsprecher mit der Spudgerspitze aus der Klebeverbindung zum oberen Gehäuse heraus.

    I found it easiest to start at the bottom (hard drive side) of the speaker.

    Michael Vovaris - Antwort

  29. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 29, Bild 1 von 1
    • Hebe die Subwoofer/rechter Lautsprecher- Einheit aus dem oberen Gehäuse heraus.

  30. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 30, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 30, Bild 2 von 2
    • Entferne die beiden äußeren Torx T8 Schrauben, mit denen jede Seite der Displayhalterung am oberen Gehäuse befestigt ist (also insgesamt vier Schrauben).

  31. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 31, Bild 1 von 1
    • Öffne das MacBook so, dass das Display rechtwinklig zum Gehäuse steht.

    • Stelle das MacBook so wie gezeigt auf den Tisch.

    • Halte das Display und das obere Gehäuse mit einer Hand zusammen und entferne gleichzeitig die Torx T8 Schraube von der unteren Displayhalterung.

  32. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 32, Bild 1 von 1
    • Halte das Display und das obere Gehäuse gut mit deiner linken Hand zusammen. Wenn du dabei einen Fehler machst, können das Display oder das Gehäuse hinfallen und die Bauteile beschädigt werden.

    • Entferne die letzte Torx T8 Schraube, die das Display noch am oberen Gehäuse befestigt.

  33. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 33, Bild 1 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 33, Bild 2 von 3 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 33, Bild 3 von 3
    • Fasse das obere Gehäuse mit deiner rechten Hand und drehe es leicht zur Oberkante des Displays hin, so dass sich die obere Displayhalterung vom Rand des oberen Gehäuses löst.

    • Drehe das Display leicht vom oberen Gehäuse weg.

    • Hebe das Display hoch und gleichzeitig weg vom oberen Gehäuse, achte darauf, dass sich keine Kabel oder Halterungen verfangen.

  34. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen, Oberes Gehäuse: Schritt 34, Bild 1 von 1
    • Entferne die vier rot markierten 1,2 mm Kreuzschlitzschrauben.

  35. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 35, Bild 1 von 1
    • Drücke vorsichtig das Trackpad an seiner Kante, die der Tastatur am nächsten liegt, aus seiner Aussparung im oberen Gehäuse heraus, aus den Rasten im oberen Gehäuse.

    • Fädle das Kabel zum Trackpad aus dem Schlitz im oberen Gehäuse heraus.

    I concur with Anonymous 596. There is a support wall that runs front to back, under keyboard, held down by 2 Phillips screws that will need to be removed & transferred to new upper case. You can see it being touched by index finger in this pic.

    Macrepair SF - Antwort

  36. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 36, Bild 1 von 1
    • Ziehe das Trackpad weg von der Außenkante des oberen Gehäuses.

    • Entferne das Trackpad und lege es beiseite.

    There's a missing step here. In addition to the trackpad, there's an aluminum structural piece that sits under the center of the keyboard, that has to be migrated from old to new case. It's clearly shown to the left of the repair-person's right hand in step 44.

    anonymous 596 - Antwort

  37. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 37, Bild 1 von 1
    • In den folgenden Schritten arbeitest du an deinem neuen oberen Gehäuse.

    • Befestige lose mit einem T6 Torx Schraubendreher die 1,1 mm Stellschraube, die mit deinem neuen oberen Gehäuse mitgeliefert wurde, im Schraubloch mit Abdeckung, in der Nähe Mitte der Öffnung für das Trackpad an deinem neuen Gehäuse.

    • Drehe sie im Moment nur eine Umdrehung ein.

    I bought a used replacement case and had to move a few parts from the old case to the replacement. This included the battery indicator cable, the clips for the trackpad and the bracket in the center of the top case. So worth it at this point to compare your old and replacement case to be sure everything you need is there.

    Ron - Antwort

    my new case came with the set screw already installed, and i couldn’t loosen it. i didn’t want to strip it and cause a bigger problem, so i left it alone. the trackpad seems to work fine so far regardless, although i may take the bottom case off and play with it a little if i get a chance.

    i also (just like Ron) had to move the trackpad clips, battery indicator and center bracket to the new case. they were not included.

    Matt - Antwort

  38. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 38, Bild 1 von 2 MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 38, Bild 2 von 2
    • Führe sorgsam das Kabel deines alten Trackpads durch den schlitzförmigen Einschnitt in deinem neuen oberen Gehäuse.

    • Halte mit einer Hand das Kabel zum Trackpad fest, während du die beiden Haltelaschen an der Außenkante des Trackpads unter der Lippe am oberen Gehäuse befestigst.

    • Ziehe am Kabel des Trackpads, während du das Trackpad in seiner Öffnung im neuen oberen Gehäuse einsetzst.

  39. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 39, Bild 1 von 1
    • Setze in jedes der äußeren Bohrlöcher im Trackpad eine 1,2 mm Kreuzschlitzschraube ein. (Insgesamt zwei)

    • Die Restlichen wirst du gleich einbauen

    • Ziehe erst die Schrauben fest, dann drehe sie eine Viertelumdrehung zurück, so dass du dein Trackpad in den nächsten Schritten ausrichten kannst.

  40. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 40, Bild 1 von 1
    • Versuche fortwährend dein Trackpad zu klicken und ziehe dabei vorsichtig die Torx T6 Stellschraube an, bis die Klicks sich anfühlen, wie beim Neugerät.

    • Du kannst am Klick-Geräusch des Trackpads hören, wenn die Schraube richtig eingestellt ist. Wenn sie zu lose ist, dann hat das Trackpad zu viel Spiel, bevor es klickt. Wenn sie zu fest ist, dann wird das Trackpad zu leicht klicken und nicht den charakteristischen lauten Mausklick erzeugen.

  41. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 41, Bild 1 von 1
    • Drehe dein oberes Gehäuse herum, so dass die Tastatur oben liegt.

    • Richte das Trackpad mittig in seiner Öffnung im oberen Gehäuse aus.

    Pour l’alignement du Tradpad mettez sur les 4 cotés des morceaux de feuille A4😜.

    Caruso - Antwort

  42. MacBook Pro (13 Zoll, Mitte 2010, Unibody) oberes Gehäuse austauschen: Schritt 42, Bild 1 von 1
    • Ziehe die äußeren beiden Schrauben an der Innenkante des Trackpads an und überprüfe an der Außenseite des oberen Gehäuses, ob das Trackpad noch richtig sitzt.

    • Wenn es gut ausgerichtet ist, dann kannst du die restlichen Kreuzschlitzschrauben an der Innenkante des Trackpads anbringen.

    • Überprüfe vor dem Zusammenbau deines Laptops nochmals, ob die Einstellung der Stellschraube immer noch richtig ist, so dass die Maus korrekt klickt.

    You can actually replace the keyboard alone fairly easily! I don't know why everyone says you have to replace the whole top case, because if you've got the guts to go this far, you might as well just peel back the illuminator cover and get to work pulling all those tiny screws in the keyboard... Just be careful when peeling up the black adhesive keyboard cover, because you will need to replace it. I used the edge of the ifixit Sesame tool (very thin flat metal opening tool) to carefully slip under any bits of adhesive, and had the keyboard exposed in no time. Also be careful because the clear plastic sheet is actually the keyboard illuminator. Once under all that, it's a mere 50 or so tiny screws, 2 screws in the power button backing, and you've got the keyboard out. Use a magnetized #000 phillips, it will make life much easier than anything else.

    Logan Bean - Antwort

    Absolutely right. I just replaced a keyboard the same way without much problem but i just want to add that those tiny screws need extra care as the heads can get damaged very easily. If damaged, they become very difficult to remove.

    Masood -

    I did just that on my mid-2010 MacBook Pro about a month ago and sadly will have to do it to my wife's Early-2011 one next week. I was cleaning all the crap off her keyboard and apparently nuked the K and 0 keys on her keyboard. Probably my ply challenge was aligning the keyboard illuminator. It's still not aligned properly on mine so some keys are better lit than others, but otherwise it was a relatively easy fix and far cheaper than replacing the entire upper case.

    John Adam Wickliffe -

    I replaced my keyboard less than an hour ago. The biggest pain/most time consuming was reattaching the ZIF connector for the keyboard and backlight. No matter what I did I could not get the %#*@ thing to reattach. What sadist designs these things? I had to walk away from the project for an hour and finally success.

    All those screws will make you go crosseyed!

    Gordon - Antwort

    It helps to put some tape along the cable going lengthwise to the cable, and then fold the end of the tape onto itself to give yourself something to hold onto. This will give you some leverage to get that puppy into the socket.

    maccentric -

    I’m glad you managed !!!

    I’m suffering :( take a part about 5 times…… ordered new (used) keyboard, the same results. I tested logic board in my daughter MAC, board works 100% no trouble ……. what could be wrong? there a secret how to reassemble keyboard parts together? I ripped a little bit black plastic thing, not top one with tiny connectors……

    In the end I have two keyboards, cleaned and taken a part, both of them acting identical when installed. Some keys respond by giving absolutely not relevant symbols, beeping noise come with almost every key i pressed…..

    Recovering after massive cappuccino spell after surprising hug :(((((

    Aleksandra Perry -

    I swear to post photo step by step, if I will achieve this one……….. assemble back to 100% working condition after total reassembling, ultrasonic cleaning and drying………. just keyboard panel.

    Give me nightmares :) will be first time I have so much trouble to fix………

    Aleksandra Perry -

    I'm wondering about putting it back together. Different wires and small parts etc were glued or adhered in some way to the case or sides or whatever, as it is put together in the beginning. Is that just to make it easier to put it back together? Should I try to stick them back the way they were with something? Can you use tape or glue if it's just a wire? I wouldn't want to use something that would melt...or is this not something to worry apout?

    ingwis - Antwort

    I just used 1/4 polymide tape, and iFixit double sided tape. Works like a champ.

    Brent Hillyer -

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

65 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 7

Letzte 30 Tage: 39

Insgesamt: 76,707