Zum Hauptinhalt wechseln

MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen

Was du brauchst

  1. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen, Unteres Gehäuse: Schritt 1, Bild 1 von 1
    • Entferne die folgenden zehn Schrauben, mit denen das untere Gehäuse am oberen Gehäuse befestigt ist:

    • Sieben 3 mm Kreuzschlitzschrauben

    • Drei 13,5 mm Kreuzschlitzschrauben

    May be helpful to have more distinct colors to identify the different screws.

    Victor Caamano - Antwort

  2. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 2, Bild 1 von 2 MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 2, Bild 2 von 2
    • Hebe das untere Gehäuse mit beiden Händen in der Nähe der Lüftungsöffnung an, damit sich die beiden Clips lösen, mit denen die beiden Gehäuseteile verbunden sind.

    • Entferne das untere Gehäuse und lege es zur Seite.

  3. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen, Akku: Schritt 3, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    P6 Pentalobe Screwdriver 2009 15" MacBook Pro Battery
    $5.49
    Kaufen
    • Entferne die beiden 5-Punkt Pentalobe Schrauben an der Oberkante des Akkus.

    • Wenn du die Festplatte austauschen willst, musst du nicht unbedingt den Schritten 3-7 folgen, um den Akku auszubauen. Allerdings ist es empfehlenswert, vor Reparaturen oder Wartungen immer alle Stromquellen von Elektrogeräten abzutrennen.

    Question: why do you remove the battery? According to Apple's official manual, this is not required (not for the mid-2009 and not for the mid-2010 15-inch MacBook Pro) - see pages 37 ff:

    http://manuals.info.apple.com/en_US/MacB...

    http://manuals.info.apple.com/en_US/MacB...

    alexkli - Antwort

    Zitat von alexkli:

    Question: why do you remove the battery? According to Apple's official manual, this is not required (not for the mid-2009 and not for the mid-2010 15-inch MacBook Pro) - see pages 37 ff:

    http://manuals.info.apple.com/en_US/MacB...

    http://manuals.info.apple.com/en_US/MacB...

    I'm interested by your experience.

    Did you have removed the optical drive without removing the battery ?

    I'm just in this step now and if it is possible I would proceed like you because removing the battery void the warranty (and there is a sticker).

    Thanks in advance.

    youyou - Antwort

    Looks like my note to step 3 appears on all repair guides that have the same step. I meant that in the context of the hard drive replacement only.

    Did you have removed the optical drive without removing the battery ?

    I haven't yet done anything, waiting for my MacBook Pro 15 inch mid-2010 to arrive.

    alexkli - Antwort

    I missed the notes and went ahead and purchased the 5 point driver for the battery before I realized it was not necessary.

    I've edited the repair guide to remove the section on the battery, but I don't have the points to approve the changes.

    Chris Davis -

    Please note - the step about removing the battery is part of a pre-requisite guide, that is used for many of the guides, most that do require removal of the battery. Also, working inside a disassembled laptop with the battery still connected risks damaging/shorting out very expensive parts.

    Eric Essen - Antwort

    Absolutely. To be clear -- ALL of the above discussion is ONLY in reference to replacing the hard drive.

    Chris Davis -

    I replaced a hard drive in a MacBook Pro of an earlier model than this without removing the battery. The hard drive wasn't right. It only worked at about half speed, and I had to replace it once more. The second time I removed the battery and all went well. The recommendation by the iFixit staff to remove the battery before working on electronic equipment is a good one.

    doug - Antwort

    What is the size of those screws... I have rounded off the socket on mine and would like to replace them.

    Ghatothkach Yadav - Antwort

    I measured the screw size, using a micrometer, its about 1.523mm in diameter and 3.186mm in length. Not sure what screw size that is. They are not easily available I guess, unless someone is selling used ones on ebay

    Ghatothkach Yadav - Antwort

  4. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 4, Bild 1 von 1
    • Biege die Ausbuchtung am Aufkleber "Warning: Do not remove the battery" mit der Spudgerspitze hoch, um die dritte Pentalobe Schraube darunter zu entfernen.

  5. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 5, Bild 1 von 2 MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 5, Bild 2 von 2
    • Hebe den Akku an seiner Plastiklasche hoch und schiebe ihn von der langen Kante des oberen Gehäuses weg.

    • Versuche noch nicht, den Akku ganz zu entfernen.

    Removing the battery is not necessary for the hard drive removal/replacement procedures.

    Erik - Antwort

    My T6 (appears to be same screw driver you have - $6 on amazon for 20piece set) did NOT fit int he battery screws...not sure if I had the wrong screws or what, but I went ahead w/o battery steps and it was pretty easy.

    Anthony Ettinger - Antwort

    I also noticed that the new SDD (from crucial) didn't have the 4 screws, so I had to move those off the old HD and onto the new one.

    Anthony Ettinger -

    Just had the same issue: T6 does not fit the battery screws ;-( ... but with a little bit more preassure it was possible to remove the screws.

    dirkvloenwagner -

  6. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 6, Bild 1 von 1
    • Kippe den Akku soweit nach hinten, dass du an den Akkukabelstecker herankommst.

    • Ziehe den Akkukabelstecker aus seinem Anschluss auf dem Logic Board und entferne den Akku aus dem oberen Gehäuse.

    • Wenn du einen neuen Akku einbaust, solltest du ihn nach dem Einbau kalibrieren.

    Excellent guide

    Kola Ajibade - Antwort

  7. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen, Optisches Laufwerk: Schritt 7, Bild 1 von 1
    • Apple klebt ein kleines Stück durchsichtigen Kunstoffs auf eine Seite des Logic Boards hinter den Stecker des Kamerakabels, um ihn im Anschluss zu befestigen. Wenn du es entfernst, dann achte darauf, dass du keine der oberflächlich befestigten Bauteile auf dem Logic Board beschädigst.

    • Halte ein Ende des Kabelhalters mit einem Finger nach unten, während du das andere Ende mit der Spudgerspitze etwas anhebst und vom Kamerakabelstecker wegdrehst.

    I found it quite easy to carefully remove the drive from under the camera cable without disconnecting it, and guide the new drive back in under. It saved time and the danger of damaging those fragile connectors.

    Glenn Richards - Antwort

  8. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 8, Bild 1 von 2 MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 8, Bild 2 von 2
    • Ziehe das männliche Ende des Kamerakabels gerade vom Anschluss weg, um es zu trennen.

    • Ziehe den Stecker parallel zur Oberfläche des Logic Boards und nicht senkrecht zu ihm.

    I would recommend leaving the camera cable plugged into the motherboard, and simply sliding the optical drive out from underneath it carefully. If you mistakenly life this connector straight up (as I did) you can damage either the cable connector or the motherboard socket. I damaged the connector on the cable and now the wifi antenna doesn't work. Replacing this damaged cable is about 10X more of a pain (in time and money) than the effort to slide the optical drive out from beneath this cable instead of disconnecting it.

    Frank Stickney - Antwort

    I agree, the same issue happened to me (My MBP no longer recognizes its wi-fi adapter). The black connector is very fragile, and very hard to slide back in after you take it out. Try not to disconnect it if you can.

    Dave Yu - Antwort

    Totally agree here, my wifi card is no longer recognized by the computer. Not sure what to do now.

    raj grainger - Antwort

    100% true! Thanx for confirming

    cj67 - Antwort

  9. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 9, Bild 1 von 1
    • Löse das Kamerakabel aus der Klebeverbindung zum optischen Laufwerk.

    When reassembling, which adhesive should be used to reattach the camera cable?

    Daniele Tamponi - Antwort

  10. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 10, Bild 1 von 2 MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 10, Bild 2 von 2
    • Dieser Schritt ist nur nötig, wenn dein Display entspiegelt ist. Wenn du ein glänzendes Display hast, dann überspringen ihn.

    • Ziehe das männliche Ende des Bluetooth-Kabels gerade aus seinem Anschluss heraus und trenne es ab.

    • Ziehe den Stecker parallel zur Oberfläche des Logic Boards und nicht senkrecht zu ihr.

    • Heble das Bluetooth-Antennenkabel mit dem flachen Ende des Spudgers aus seinem Anschluss auf der Platine.

    How can I determine if I have an antiglare display?

    Thanks!

    Dan

    Dan Neunaber - Antwort

    If you have the part in step 10, you do. If you don’t, you don’t (looks like pic in step 9).

    maccentric -

    As already pointed out in a comment to step 8, it is possible to slide carefully out the drive from underneath the bluetooth board without touching it, and to insert the replacement drive in the same way, avoiding to perform this step and the next one.

    spiderbatbug spiderbatbug - Antwort

  11. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 11, Bild 1 von 2 MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 11, Bild 2 von 2
    • Dieser Schritt ist nur nötig, wenn dein Display entspiegelt ist.

    • Entferne die beiden 8 mm Kreuzschlitzschrauben, mit denen der Halter des Bluetooth/Kamerakabels am oberen Gehäuse befestigt ist.

    • Eine der Schrauben bleibt in der Erdungsöse des Bluetooth/Kamerakabels hängen. Wenn du das Display austauschst, musst du diese Schraube auf das neue Display übertragen.

    • Hebe die Haltereinheit des Bluetooth/Kamerakabels aus dem oberen Gehäuse heraus.

  12. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 12, Bild 1 von 1
    • Heble den Stecker des optischen Laufwerks mit dem Spudger gerade vom Logic Board weg.

  13. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 13, Bild 1 von 1
    • Die innere Seite des optischen Laufwerks ist mit einer einzelnen 3,5 mm Kreuzschlitzschraube am oberen Gehäuse befestigt. Drehe sie heraus.

    Totally stripped this screw, no idea what to do know.

    What - Antwort

  14. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 14, Bild 1 von 1
    • Die äußere Seite des optischen Laufwerks ist mit zwei 3,5 mm Kreuzschlitzschrauben am oberen Gehäuse befestigt. Drehe sie heraus.

    When installing the HD bay, the screws here will not go back. Not sure if the bracket/holes are somehow different. After completing the install, everything seems secure. Does anyone think not having these screws is critical beyond securing the drive?

    toddfletcher - Antwort

  15. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 15, Bild 1 von 1
    • Hebe das optische Laufwerk am linken Rand an und ziehe es aus dem oberen Gehäuse heraus.

  16. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen, Optisches Laufwerk: Schritt 16, Bild 1 von 1
    • Ziehe das Kabel zum optischen Laufwerk gerade vom Laufwerk weg und trenne es ab.

    • Wenn sich eine CD oder ein anderes Objekt im Laufwerk verklemmt hat, dann haben wir dazu eine Reparaturanleitung.

  17. MacBook Pro (15 Zoll, Mitte 2009, Unibody) optisches Laufwerk austauschen: Schritt 17, Bild 1 von 1
    • Entferne die beiden schwarzen Kreuzschlitzschrauben #0, mit denen die kleineMetallhalterung befestigt ist. Übertrage diese Halterung auf dein neues optisches Laufwerk oder den Festplattenkäfig.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

49 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

4 Kommentare

My replacement drive had screwholes in slightly different places and a different connector ribbon, but I was able to successfully swap the drive top plate, inner side screw bracket and connector ribbon with the ones from the existing drive.

Steve Seear - Antwort

Replaced the drive. DVD inserts. Drive works. But the DVD won't eject. Seems like the slot in the case and the drive don't align. Any Ideas?

Gabriel Lieb - Antwort

Do you think, It’s a good solution to remove the drive without replacing it?

Oliver - Antwort

I just replaced drive…tried to insert disk and no go. Do I need to reset something software wise??

Doe - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 11

Letzte 30 Tage: 42

Insgesamt: 79,261