Einleitung
Hier wird der Austausch des Logic Boards gezeigt.
Was du brauchst
-
In diesem Schritt verwendetes Werkzeug:Magnetic Project Mat$19.95
-
Entferne die folgenden zehn Schrauben, mit denen das untere Gehäuse am oberen Gehäuse befestigt ist:
-
Zwei 2,3 mm P5 Pentalobe Schrauben
-
Acht 3,0 mm P5 Pentalobe Schrauben
-
-
-
Versuche mit den Fingern zwischen das obere und das untere Gehäuse zu kommen.
-
Ziehe das untere Gehäuse behutsam vom Oberen weg.
-
Entferne das untere Gehäuse und lege es zur Seite.
-
-
-
Das untere Gehäuse ist in der Mitte durch zwei Plastikklammern mit dem oberen Gehäuse verbunden.
-
-
-
Entferne die Plastikabdeckung über der Platine des Akkuanschlusses.
-
-
-
Entferne die folgenden Schrauben, mit denen die Platine des Akkuanschlusses am Logic Board befestigt ist:
-
Zwei 2,8 mm T6 Torx Schrauben
-
Eine 7,0 mm T6 Torx Paß-Schulterschraube
-
-
-
Mit einer Pinzette kannst du die Plastikabdeckung rechts an der Platine des Akkuanschlusses entfernen.
when doing this with metal tweezers as instructed in the video, it was difficult to get off and apparently while i was trying to do it, the tweezers went too far under and i believe made contact with the screw underneath? there was a zzz noise, an orange flicker and a little stream of smoke that came out. i freaked out and put everything back together to see if the laptop even still worked, it turned on and everything but died right away (i drained it before doing the repair anyway, so i was surprised it turned on at all).
i finished the battery repair and did several other things while in there. i have charged it all the way as recommended and will use it later on to see how everything is, im hoping that it’s a okay, but could someone explain to me what happened and the possible consequences?
-
-
-
Entferne die 6,4 mm T6 Torx Breitkopfschraube, mit der die Platine des Akkuanschlusses am Logic Board befestigt ist.
-
-
-
Ziehe die Platine des Akkuanschlusses vorsichtig vom Logic Board ab.
-
Es empfiehlt sich, die Batteriekabel nur leicht zu biegen, um die Platine über dem Logic Board und aus dem Weg zu halten.
-
-
-
Schnapp dir den Interposer mit einer Pinzette.
-
Hebe den Interposer aus dem Logic Board heraus und entferne ihn.
you must lift it absolutely vertically, or it fouls against the locator pin in the corner- you can easily get the impression that it won’t come over the end of this pin- almost like it’s rivetted in. it isn’t. get a good grip on it with the tweezers in the centre hole & one of the sides, & lift it STRAIGHT up.
I would recommend to use plastic tweezers in order to reduce risk of damage.
Second that. If you have thin heat shrink tubing, form some over the tweezer tips. If the tubing is thin and small enough in diameter you’ll see the serrations of the tweezer tips.
wat is the model this SSD
-
-
-
Entferne folgende Schrauben, welche den Kühlkörper an der Einheit des Logic Boards befestigen:
-
Eine 2,4 mm Kreuzschlitzschraube #00
-
Eine 3,4 mm Torx T5 Schraube
-
Vier 2,7 mm Torx T5 Schrauben
Hi,
found 4 rubber spacers on the 4 2,5mm screws
-
-
-
Heble die rechte Seite des Steckers am I/O Board Datenkabel mit dem flachen Ende des Spudgers aus seinem Anschluss auf dem I/O Board.
-
-
-
Schiebe das flache Ende des Spudgers unter die linke Seite des Steckers am I/O Board Datenkabel.
-
Verdrehe den Spudger vorsichtig, um den Stecker des I/O Board Datenkabels aus seinem Anschluss auf dem Logic Board zu lösen.
-
-
-
-
Schiebe den Stecker des iSight Kamerakabels mit der Spudgerspitze gerade aus seinem Anschluss auf dem Logic Board heraus.
Bummer. It wasn’t clearly communicated how to separate this connector, and I accidentally pried the socket from the board. The connector slides out horizontally, so don’t pry up from the bottom.
Yes. That's a tricky little guy! I'm very lucky that I didn't break it! I couldn't figure out which direction to 'walk' it, but after reading the comments above it became more clear. When I first started trying to detach it I was trying to lift it up like all the previous connections. It was giving too much resistance, so I put the magnifying glass over the picture and then the connection. Back and forth I was looking. My hand slipped. I thought I broke it! But I saw that it had moved 'backwards' a bit. Then it became clear on which way to 'walk' it. It moves back in the direction of the cable it's connected to. It slides in like the newer fuses do in a car. A neat little learning experience! Thank you folks who add comments and to the people who put this directorial together.
-
-
-
Klappe den Sicherungsbügel am ZIF Verbinder am Flachbandkabel des rechten Lüfters mit der Spudgerspitze hoch.
-
Ziehe vorsichtig das Flachbandkabel zum rechten Lüfter aus seinem Sockel auf dem Logic Board.
Hey! You skipped a step!
What about the cable (don't know what it does) that runs right across the fan, interfering with pulling the fan out.
It's still in place in Step 14, but here in Step 15 it's magically removed itself, and can be seen resting luxuriously on top of the Airport card.
How do we get that outta there?
Like @victorgav mention, Just need a step before this one, which is to remove the cable that goes across the top of the fan.
Thanks for bringing this up! It looks like the guide was missing the iSight cable disconnection steps. I’ve added the missing steps.
-
-
-
Entferne die drei 3,1 mm Torx T5 Schrauben, welche den rechten Lüfter an der Logic Board Einheit befestigen.
-
-
-
Klappe den Sicherungsbügel am ZIF Sockel am Flachbandkabel des linken Lüfters mit der Spudgerspitze hoch.
-
-
-
Entferne die drei 3,1 mm Torx T5 Schrauben, welche den linken Lüfter an der Logic Board Einheit befestigen.
-
-
-
Drücke die Kanten des Steckers an der Stromversorgung des I/O Boards mit der Spudgerspitze gerade aus dem Anschluss auf dem Logic Board.
-
-
-
Schiebe das flache Ende des Spudgers unter den Stecker der Tastaturbeleuchtung und das Logic Board.
-
Drehe das flache Ende des Spudgers vorsichtig nach oben und hebe so den Stecker der Tastaturbeleuchtung aus seinem Anschluss auf dem Logic Board.
-
-
-
Fasse die schwarze Plastiklasche an, welche am Verschluss des Displaydatenkabels angebracht ist, und drehe sie in Richtung der Seite mit dem Stromanschluss (DC-In) des Computers.
-
Ziehe das Displaydatenkabel gerade aus seinem Anschluss auf dem Logic Board.
-
-
-
Hebele den Stecker am Kabel der Kopfhörerbuchse aus seinem Anschluss auf dem Logic Board heraus.
-
-
-
Klappe den Sicherungsbügel am ZIF Anschluss des Flachbandkabels zum Mikrofon mit der Spudgerspitze hoch.
-
Fasse die Plastiklasche und ziehe das Flachbandkabel zum Mikrofon aus seinem Anschluss heraus.
-
-
-
Klappe den Sicherungsbügel am ZIF Anschluss des Flachbandkabels zur Tastatur mit dem flachen Ende des Spudgers hoch.
-
Fasse die Plastiklasche und ziehe das Flachbandkabel zur Tastatur aus seinem Anschluss heraus.
-
-
-
Wiederhole den vorherigen Vorgang und löse das Flachbandkabel zum Trackpad aus seinem Anschluss auf dem Logic Board.
I discovered that if the trackpad cable is damaged the keyboard will not work. I replaced the trackpad cable which had two damaged Ribbon pens. Once TP cable was replaced the keyboard also worked!
-
-
-
Schiebe das flache Ende des Spudgers unter den Stecker am rechten Lautsprecherkabel.
-
Hebele vorsichtig den Stecker am rechten Lautsprecherkabel aus seinem Anschluss auf dem Logic Board.
-
-
-
Hebele den Stecker am SSD Kabel mit dem flachen Ende des Spudgers aus seinem Anschluss auf dem Logic Board.
-
-
-
Schiebe die Spudgerspitze unter den Stecker am linken Lautsprecherkabel.
-
Hebele vorsichtig den Stecker am linken Lautsprecherkabel aus seinem Anschluss auf dem Logic Board.
-
-
-
Entferne die neun 3,3 mm Torx T5 Schrauben, welche das Logic Board und das MagSafe DC-In Board am oberen Gehäuse befestigen.
-
-
-
Fasse vorsichtig die Ecke des Logic Boards an (gegenüber den I/O Anschlüssen) und hebe das Logic Board aus dem oberen Gehäuse.
When re-installing the Logic board, be careful not to trap any of ZIF cables under the board.
You’ll need to tilt the board up from the end away from the DC-IN board in order to get the IO connectors inserted all the way. Be careful with the little fingers on top of the IO connectors.
I had previously replaced the battery with the Newer Tech battery. The battery cable is not as flexible as the original battery, making the removal and insertion of the trackpad cable difficult.
-
-
-
Schiebe vorsichtig die Kanten des Steckers am MagSafe Kabel aus seinem Anschluss auf dem Logic Board heraus.
-
-
-
Ziehe den Stecker am MagSafe Kabel gerade aus seinem Anschluss auf dem Logic Board heraus.
-
-
-
Das Logic Board bleibt übrig.
Removing worked fine........ Followed every step carefully.... Getting another board in will be another chapter.... And hopefully the machine will work again.
Thank you ifixit.......
Yes! I just finished. Yay!! Couldn't have done it without this tutorial, so Thank you very much!!! I think installing the new one will be more difficult. I could have just went out and bought a new one, but this has been much more fun!
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
32 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
Ein Kommentar
NOTE: The logic boards you are placing into your Macbook Pro as a replacement probably are not coming from systems that are current and actively being used (they may have been on the shelf for a while)…more importantly they are almost certainly not coming from systems that were fully updated and running MacOS High Sierra. Realize that if you have updated your Macbook and are running High Sierra, your hard drive has been converted to the latest APFS Apple file system. In order for an older logic board to be able to read any of your APFS hard drive will require that the logic board gets the latest SMC/firmware updates. Without this you will not be able to boot from your hard drive. See how I was able to correct this dilemma here: Hard Drive/OS not recognized after logic board replacement
If don’t have one of those neat project mats, then you can use small pieces of flattened blu-tack to hold the screws. If you arrange them in the shape of your mac book cover, and put the screws down methodically, you can get a one-to-one mapping of the screws to the correct screw holes.
Toby Thurston - Antwort
Or you can use an ice tray where you put the screws and the parts in separate bays in the same order as they come in the instructions.
timofej.se -
This is great! I used a small magnetic white board, and wrote on it to identify the parts as I went. This whole process, from the fast shipment to the great instructions to the complete, high quality, tool kit has been great. I’m typing this comment on my resurrected laptop. Thank you! Sue
Susan Greer - Antwort
It would be a good idea if people recorded in the comments which screws go where so that, if someone lost their screw positions, they could recover them from the comments.
Raymond Shpeley - Antwort