Einleitung

Hier wird der Austausch des Lüfters gezeigt.

Vor dem Einbau des Kühlkörpers musst du neue Wärmeleitpaste aufzutragen. Unsere Anleitung hilft dir dabei.

Entferne die folgenden zehn Schrauben, die den Boden des Gehäuses befestigen:
  • Entferne die folgenden zehn Schrauben, die den Boden des Gehäuses befestigen:

    • Zwei 2,3 mm Pentalobe Schrauben

    • Acht 3,0 Pentalobe Schrauben

For all the screws you use the P5 pentalobe screwdriver?

Carlos - Antwort

Pentalobe is only for the screws on the bottom cover. The Torx screw driver is for the remainder.

Fredrik -

Is the Pentalobe screwdriver mentioned in the tools list? I did not have one so I used a filed down flat blade screwdriver. Not a fantastic idea, but it works.

Alex Birkett - Antwort

Yes, it's mentioned on the top of this page. P5 Pentalobe to be precise. I didn't have one either, so I bought one from iFixit and that works fantastic. An absolutely precise fit, which is important especially when you might open your MacBook a couple of times during the years you own it. Not using the correct tool might do more harm to the screws than you want! I once had this with a Lenovo Yoga 3 Pro, which has Torx screws (T4 I think) and I used cheap Chinese quality tools, with the result that both the tool and one of the screws are damaged.

addvariety -

the macbook in the picture is 2012. does it has the same structure as 2013?

Edison - Antwort

I never, ever, ever considered using anything but the correct tool on the Pentalobe screws. Too easy to strip and void your warranty (if still in effect), as well as make it almost impossible to get inside later for another upgrade or repair. The Wiha P5 Pentalobe screwdriver fits like a glove and costs only about $11 (a fraction of your drive's price)at Amazon.com. Get it!

marketing - Antwort

is P5 supposed to be for all 10 screws? it works on the 2x 2.3mm at the top, but not for the 8x others for me. what size screwdriver for the 3mm? thanks

monsieurescargot - Antwort

Yes, the p5 works for all 10 pentalobe screw heads for bottom cover. The the different size mm reference only refers to the difference in length of the screws, but again both heads are p5.

Antoine Thornton - Antwort

Gehe mit deinen Fingern zwischen das obere und das untere Gehäuse.
  • Gehe mit deinen Fingern zwischen das obere und das untere Gehäuse.

  • Hebe die untere Gehäuseabdeckung vorsichtig vom Gerät ab.

Kommentar hinzufügen

  • Der Gehäuseboden ist durch zwei Steckverbindungen in dessen Mitte mit dem Gerät verbunden.

  • Drücke während des Zusammenbauens vorsichtig auf die Mitte des Gehäusebodens, um die Steckverbindungen wiederherzustellen.

There are two screws that are shorter-they go to the back near the vent.

wrbandllm - Antwort

This was already mentioned at the start, it says 2x 2.3mm screws and those are coloured red instead of orange for the other ones in iFixit's image.

addvariety - Antwort

What is the black vinyl-y sticker on the inside of the case (some sort of shield?). I was forced to slightly puncture it in order to replace the feet on my laptop. Thanks in advance.

Tommy Huang - Antwort

  • Falls nötig, entferne die Plastikabdeckung vom Batterieanschluss.

Do you know where I can purchase this plastic cover? Mine is missing and no one will work on my computer without it.

jodieabc - Antwort

There is no point on going near the battery or logic board. I cut out these steps with no issue. It is precautionary but unnecessary.

Jaime Leonard - Antwort

  • Trenne den Stecker der Batterie mit dem flachen Ende eines Spudgers von seinem Anschluss auf dem Logic Board.

  • Gehe sicher, dass du nur den Konnektor und nicht den Sockel anhebst. Ansonsten besteht die Gefahr das Logic Board irreparabel zu beschdäigen.

I have a friends MacBook Pro that has some water damage that caused the MacBook not to be able to use battery power, but still work when plugged into A/C. Upon further inspection I can see visible corrosion on a few of the 9 cables going from the battery connector to that small circuit board. Is it possible to just replace that circuit board?

jramsey21 - Antwort

I have the some problem. I was thinking to replace the whole battery but I am not it will solve the problem. Any suggestions?

salvatorebarbera -

Sometimes it can be enough to just clean the contacts without having to replace the entire board. Dosent work for complicated IC's like plcc type, where corrosion is underneath the chip. Here you will have to reheat and reapply the IC.

andrehedegaard -

Have either of you replaced the battery and/or circuit board to fix the MacBooks with the water damage ? I have the same problem with the MacBook working fine when connected to power but dying immediately when the power cord is removed.

Steve - Antwort

Hi, Steve. I had the same problem: Macbook Pro 15 retina with coffee damage. And it worked fine when connected to power. I made it working after replacing the whole battery. It seems that circuit connected to the battery becomes disabled to prevent short circuit.

Vadim Gribanov -

When placing the battery connector back into the socket on the logic board, check that every part of connector is pressed down. You should hear a soft click when it's back in place.

Ethan Tarquin - Antwort

Thanks for the comment. My MBP isn’t powering on after I walked through these steps, and I assume it is because the battery connector isn’t fully connected. (I can’t check yet since I borrowed the pentalobe screwdriver)

Caleb Steinborn -

+1

I thought I made sure it was connected but when running the computer it only detected the battery but couldn’t power it. I had to run with power adapter. Also it didn’t charge. I guess some pins were connected but not all. To verify that all were connected I removed the plastic cover, placed it carefully completely flat, and then reattached the plastic cover. After that it worked!

Jonas Ehrs -

If I only want to replace the trackpad cable, then which steps should I skip? This step seems unnecessary

Parth Gudhka - Antwort

  • Biege den Stecker der Batterie etwas zur Seite, um während der Reparatur einen versehentlichen Kontakt mit dem Anschluss zu verhindern.

If you miss or let this step for later like I did, the power left in the battery even though the computer is completely shut down, will screw up the I/O board cable like I did. I noticed this after I put all the pieces back, turn the computer on and surprise, no wifi hardware is detected. -.-

sebasgaes - Antwort

I put a small piece of blue painters tape on the battery connector contacts to prevent it from accidentally making a connection and shorting. This helped keep things a bit more protected.

LaymanLab - Antwort

That’s a great idea!

David Lilliebridge - Antwort

I used a small piece of paper to prevent the connector from connecting, no need to wrestle with even low-stick adhesive.

dbrick - Antwort

  • Entferne vorsichtig den Gummidämpfer des Ventilators von der Kante des Kühlkörpers.

  • Dieser Dämpfer umfasst den Kühlkörper und sitzt in Schlitzen am Lüfterkanal. Achte beim Wiederzusammensetzen darauf, dass die entsprechenden Laschen in die Aussparungen im Lüfterkanal passen.

For reassembly, I found it easier to loosen the lone top left 2.4 mm Phillips #000 before putting the fan bumper back in.

Boston Hampton - Antwort

  • Löse mit dem flachen Ende eines Spudgers die vier Schaumstoffaufkleber von den Schrauben des Kühlkörpers ab.

How should I reapply those little foam stickers? I guess not with normal glue.

bboy.sidekick - Antwort

  • Der Kühlkörper ist mit fünf Schrauben am Logic Board befestigt. Drehe sie heraus:

    • Vier 2,6 mm T5 Schrauben.

    • Eine 2,4 mm Kreuzschlitz #000 Schraube.

Kommentar hinzufügen

  • Entferne den Kühlkörper vom Laptop.

  • Beim Wiedereinbau musst du Wärmeleitpaste auftragen. Unsere Anleitung zeigt, wie es geht.

Kommentar hinzufügen

  • Drücke abwechselnd mit der Spudgerspitze auf beiden Seiten des Steckers am Kabel der iSight Kamera, um ihn so aus seinem Sockel auf dem Logic Board herauswandern zu lassen.

I found this to be the most difficult step. There is a need to get positioned so that you have the leverage to push hard enough at exactly the point shown in the photo without risking slipping and perhaps damaging the CPU nearby

Tony M - Antwort

Very helpful tip from Tony.

Thomas Sturgill - Antwort

  • Löse das iSight Kamerakabel vom Gehäuse des Lüfters ab, um es aus dem Weg biegen zu können.

Kommentar hinzufügen

  • Klappe den Sicherungsbügel am ZIF Verbinder des Lüfters mit der Spudgerspitze hoch.

  • Ziehe vorsichtig das Lüfterkabel aus seinem Sockel.

my cable was glued, had to be pryed up first.

maccentric - Antwort

  • Entferne folgende Torx T5 Schrauben, welche den Lüfter am oberen Gehäuse befestigen:

    • Eine 5,0 mm Schraube

    • Zwei 3,6 mm Schrauben

Kommentar hinzufügen

  • Hebe den Lüfter am Ende hoch, welches am nächsten zum Displayscharnier liegt, und entferne ihn vom oberen Gehäuse.

Um, this guide should include steps for applying thermal paste, including instructions to clean the mating surfaces, and pictures showing how much thermal paste to use.

TheIronGiant - Antwort

Hi @theirongiant, there are generic thermal paste application instructions linked in the introduction “Don't forget to follow our thermal paste application guide before you reinstall your heat sink.”

Sam Lionheart -

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

13 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Sam Lionheart

Mitglied seit 18.10.2012

337.138 Reputation

535 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

112 Mitglieder

6.703 Anleitungen geschrieben

Very clear guide, and highly informative photos. It might be useful to add that the PL5 screws on the back of the case do not insert vertically. These insert at a slight angle and attempting to insert them straight will cause cross treading.

Robert Chave - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 8

Letzte 7 Tage: 81

Letzte 30 Tage: 368

Insgesamt: 26,902