Zum Hauptinhalt wechseln

MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen

Was du brauchst

  1. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Auto Boot deaktivieren: Schritt 1, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Auto Boot deaktivieren: Schritt 1, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Auto Boot deaktivieren: Schritt 1, Bild 3 von 3
    • Zuallererst musst du die automatische Startfunktion (Auto Boot) deines Macs deaktivieren. Auto Boot schaltet deinen Mac ein, wenn du ihn aufklappst, was versehentlich beim Auseinanderbau passieren kann. Benutze diese Anleitung oder befolge die anschließende Kurzversion zum Deaktivieren von Auto Boot. Dieser Befehl funktioniert eventuell nicht auf allen Macs.

    • Schalte deinen Mac ein und starte Terminal.

    • Kopiere den folgenden Befehl und füge ihn im Terminal ein (oder tippe ihn exakt so ein):

    • sudo nvram AutoBoot=%00

    • Drücke die Eingabetaste [return]. Wenn du dazu aufgefordert wirst, gib dein Administratorpasswort ein und drücke erneut [return]. Hinweis: die Return-Taste kann auch mit ⏎ oder "enter" gekennzeichnet sein.

    • Nun kannst du deinen Mac sicher herunterfahren und das untere Gehäuse öffnen, ohne dass er sich versehentlich einschaltet.

    • Nachdem deine Reparatur zu Ende ist und dein Gerät wieder erfolgreich zusammengebaut ist, musst du Auto Boot mit folgendem Befehl wieder aktivieren:

    • sudo nvram AutoBoot=%03

    Is this step necessary? I can’t perform this step as I am attempting to repair water damage and need to remove logic board & most likely replace the battery.

    Macrepair SF - Antwort

    @mac_medic You definitely don’t want the power coming on while the board is wet. In your case, I think powering on the machine to disable Auto Boot would do more damage than it prevents. I agree, skip this step and be prepared to disconnect the battery quickly if the laptop automatically powers on. Good luck!

    Jeff Suovanen -

    Thats right! You don't want power running while working on your logic board.

    Dan -

    This did not work when running High Sierra.

    Kyle B - Antwort

    Tried this on a 2018 MBP 13” Touchbar (there’s no iFixit guide for this model yet). Need to replace a broken screen.

    Luckily I managed to connect to an external screen (Cmd-Down Brightness to switch displays) and enter above command. Seems to work, but there’s another problem with this model - it powers up as soon as any key is pressed……. ffs <gnashes teeth>

    Cool_Breeze - Antwort

    I unscrew the battery first and wrap electrical tape over the logic board battery connector before attempting any repairs to the board. Haven’t had any problems yet and I’ve worked on about 10 of these models already. Also when you open the bottom case use a suction cup at the bottom and pull up then run a plastic spudger along the edges to disconnect the clips. Also only use a plastic spudger on the board. Saw a youtube video from a repair shop and he did not disconnect the power and used all metal tools during the entire process of removing the board. His last step was to disconnect the battery terminal.

    Brian - Antwort

    Is this step necessary if my mac can turn on? Battery fully dead(

    Nursat b - Antwort

    BEFORE YOU START: The included torx head stripped off before I was done (and you might need an additional T4) so stop now and go buy a good one. Also they fail to warn you above to get some blue threadlocker ahead of time.

    Jason Sherron - Antwort

    This command did not work for me and I read that sometime in later 2020 Apple stopped this command from working…any ideas on a work around?

    Patrick Machacek - Antwort

    Not able to do that with damaged screen

    richardjgreen - Antwort

    If you have a damaged screen you can still use a converter from thunderbolt (USB 3) to HDMI and plug your Macbook Pro to your TV as monitor display. Just make sure to chose the right Source (HDMI IN) in your TV. I did it and to make it work I unplug and plug again in my Macbook and so I could disable the Auto boot

    Roberto Sanchez Bustos -

    Hi. This does not work on 2018 13” MacBook Pro with Touch Bar. I did exactly this to disable auto boot. But when I check by using nvram -p it says: auto-boot true. Am I doing something incorrectly? I did everything step by step. Copied and pasted the sudo command, pressed enter and then entered my password. I have Big Sur 11.1 installed. Is there any other way since I need to replace the screen. Thank you. Adrian

    Adrian Vizik - Antwort

    Hi everyone. This is also a little pointless if you can’t see anything on the screen, and you don’t have a display adapter to USB C to display it. I agree with Brian about removing the back and disconnecting the battery cable before you even think about opening the lid of the MacBook. Applying the insulation tape is also a handy little tip that just makes sure there is no way to discharge from either the board or battery.

    Roberto Enrieu - Antwort

    running `nvram -p | grep 'AutoBoot'` in terminal verifies that it was accepted

    result: `AutoBoot %00`

    Marek Polák - Antwort

    Running Big Sur 11.6.7 on a 2019 16" MBP, it's "auto-boot". So it's: nvram -p | grep 'auto-boot' to display the current state, the default is true - and then to change it, sudo nvram auto-boot=false which turns it off.

    Ed Mechem -

    This step is completely unnecessary if you follow the guide to disconnect the battery properly. Just put some tape between the battery and logic board connection to prevent it from accidentally touching and therefore powering on the laptop.

    Grant Ormsby - Antwort

    It took me a few tries to make this command work, as I was able to copy and paste the command into Terminal, but could not type in my laptop’s password. I finally typed my password into a text document, copied it (command C), and then pasted it into Terminal and it worked.

    tommy404 - Antwort

    I didn’t do this. Mine never auto-booted before I replaced the battery. Now it does.

    hatuxka - Antwort

    BEFORE YOU DO ANYTHING - CHECK THE BATTERY!

    I-fixit sent me a bad battery, which I didn’t realize until it was already install. They sent me a new one, but I wasted hours uninstalling and reinstalled.

    Get a volt meter and measure the voltage on the output of the battery pack. If it reads 0 V, SEND IT BACK. It should read over 2 V.

    bcardanha - Antwort

    I've just received my replacement battery and it reads 0,042V between the two main connectors. Do you think it's dead?

    peter sussex -

    When I did this from Terminal.app within Recovery Mode, the “sudo” was not recognized but I could invoke it without the sudo part. It seems to have been accepted when looking at “nvram -p”

    johann beda - Antwort

    When in Recovery Mode, you already have superuser powers. So you don't need to prefix commands with the sudo command to invoke them with root privileges; you already have them. Do a pwd (print working directory) after opening Terminal in Recovery Mode, and you'll see that you're in the root user's directory.

    Ed Mechem -

    I received the battery kit for my 2018 MacBook Pro and as per the above comment from bcardanha - Oct 12, 2021, I checked the voltage on the pads marked + and - . It was zero volts so I panicked a bit.

    I sent a message on the iFixiT Facebook page and I got no reply. I finally found the customer service email for Ifixit Europe and sent them an email voicing my concern as I was not keen to work for couple of hours just to discover that the battery is faulty. I had an almost instant reply on the email (kudos to them) and they adviced me to go ahead and install the new battery as the voltage measured when battery is not connected is not relevant.

    I took a leap of faith and after two hours… the new battery showed 50% charge and everything seems to be working just fine. I am happy it worked.

    Mircea Comanici - Antwort

    After removing the old battery and installing the new battery I powered up the MBP before screwing the bottom on. I discovered the my keyboard would not function. It took a few hours of investigation and frustration that I discovered the track pad power ribbon had become partially dislodged from the trackpad. I was able to see that this through the little machined slot where the battery sat. I had to remove the trackpad to reinsert the power ribbon back into the connector in the trackpad. after reassembling and reinstalling the battery etc the keyboard worked. Just food for thought if your run into the keyboard issue.

    Ed Mease - Antwort

    This should be the default. IMO I tell you to power on - not the lid.

    G Sena - Antwort

    Est ce que cela fonctionne sur un macbook pro 2017 sans touchbar ?

    maël muzelet - Antwort

    Bonjour Maël, oui, ce tutoriel concerne "les MacBook Pro 2016 (et plus récents) et les MacBook Retina 12" 2017 (et plus récents)"

    Claire Miesch -

    Excellent instructions. I was able to follow and install the new screen. I recommend that you get a good set of tools before you begin. I started with an inexpensive repair kit bought online. The Penta and torx bits failed. I bought an IFIXIT kit with quality bits and I was able to do everything I needed.

    Tom Markham - Antwort

    If you're not running an admin account the sudo command won't work (which honestly, you should not be running admin). Rather than logging in to your admin amount via the OS, in the terminal type "login [admin username]," then the password and you'll be able to do the sudo command as described above. Once you're complete, type "logout [admin username]" and you'll be good to go. Obviously replace [admin username] with whatever the account name for your admin user is.

    arichard2401 - Antwort

    For those unable to complete this step because the screen is too damaged I recommend leaving your macbook on until the battery dies.

    Nicholas R Licato - Antwort

    Just replaced my 2018 15" MBP battery. Running Sonoma.
    I found no way to disable AutoBoot (The status can be checked in the Power section of system report).

    Anyway, i left my battery completely drain before opening the MBP, and had no issues during the process.

    Cédric Bontems - Antwort

    After sending this command in terminal when I checked what happens if I now open the lid, instead the screen lit slightly up (still black) then a battery symbol showing the charging state showed up.

    Now, after replacement of the battery, this is all I get to see.

    No reset of NVRAM nor PRAM helped.

    Currently the new battery charges (58% atm) and it feels like it‘s mocking me.

    webrockers - Antwort

    I suspected the keyboard or TouchID sensor wouldn’t work, so I went on and checked every connector.

    I missed connecting the left TouchID sensor from step 31.

    webrockers -

  2. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Pentalobe-Schrauben entfernen: Schritt 2, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Magnetic Project Mat
    $19.95
    Kaufen
    • Bevor du dein MacBook Pro auseinandernimmst, ziehe den Stecker und fahre es herunter. Schließe das Display und lege das Gerät mit der Unterseite nach oben auf eine weiche Oberfläche.

    • Entferne die sechs Schrauben, mit denen das Gehäuseunterteil befestigt ist, mit einem Pentalobe P5 Schraubendreher:

    • Zwei 6,2 mm Schrauben

    • Vier 3,4 mm Schrauben

    • Achte während der ganzen Reparatur auf jede einzelne Schraube und sorge dafür, dass sie wieder an ihre alte Stelle zurück kommt, damit kein Schaden entsteht.

  3. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Einen Spalt mit Hilfe eines Saughebers erzeugen: Schritt 3, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Einen Spalt mit Hilfe eines Saughebers erzeugen: Schritt 3, Bild 2 von 2
    • Drücke einen Saugheber vorne mittig auf das Gehäuseunterteil des MacBook Pro.

    • Hebe den Saugheber an, damit zwischen dem Gehäuseunterteil und dem Rahmen ein kleiner Spalt entsteht.

  4. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Rasten lösen: Schritt 4, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Rasten lösen: Schritt 4, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Rasten lösen: Schritt 4, Bild 3 von 3
    • Setze eine Ecke eines Plektrums in den Spalt zwischen dem Gehäuseunterteil und dem Rahmen ein.

    • Schiebe das Plektrum um die nächstgelegene Ecke und bis zur Hälfte an der Seite des Gehäuses entlang.

    • Dadurch wird die erste von vier versteckten Rasten gelöst, mit denen das Gehäuseunterteil am Rahmen befestigt ist. Du solltest hören und spüren können, wie sich die Raste löst.

  5. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 5, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 5, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 5, Bild 3 von 3
    • Wiederhole den vorigen Schritt auf der gegenüberliegenden Seite, indem du das Plektrum unter das Gehäuseunterteil steckst und entlang der Seite nach oben führst, bis die zweite Raste gelöst ist.

    Recommend being very careful on this step and the following step when using any opening tool to always keep the “pointy end” up when prying, especially about 40mm up the side, to avoid completely destroying the speaker diaphragms.

    just chris... - Antwort

  6. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 6, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 6, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 6, Bild 3 von 3
    • Stecke das Plektrum jetzt nochmal unter den vorderen Rand des Gehäuseunterteils, bei einem der beiden mittleren Schraubenlöcher.

    • Drehe das Plektrum kräftig, damit die dritte Raste gelöst wird, mit der das Gehäuseunterteil am Rahmen befestigt ist.

    • Wiederhole diesen Vorgang bei dem anderen Schraubenloch in der Mitte und löse auch die vierte Raste.

  7. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 7, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 7, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 7, Bild 3 von 3
    • Ziehe das Gehäuseunterteil fest zur Vorderseite des MacBooks hin (weg von den Scharnieren), so dass sich die letzten Rasten lösen, mit denen das Gehäuseunterteil noch befestigt ist.

    • Ziehe erst an der einen Ecke, dann an der anderen.

    • Ziehe zur Seite hin - nicht hoch.

    • Das kann relativ viel Kraft erfordern.

    I am sure that there are two snap lock things is the middle as well, not only on the side, is there a way to open that in a correct way too?

    Jack Jin - Antwort

    I found using the suction cup tool to help slide the cover helps.

    Clem Wang - Antwort

  8. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Gehäuseunterteil entfernen: Schritt 8, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Gehäuseunterteil entfernen: Schritt 8, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Gehäuseunterteil entfernen: Schritt 8, Bild 3 von 3
    • Entferne das Gehäuseunterteil.

    • So wird das Gehäuseunterteil wieder eingebaut:

    • Lege es richtig hin und richte die Klammern nahe am Scharnier aus. Drücke es nach unten und schiebe die Abdeckung zu den Scharnieren hin. Es sollte sich nicht mehr weiter schieben lassen, wenn die Klammern einrasten.

    • Wenn die Klammern ganz eingerastet sind und das Gehäuseunterteil korrekt ausgerichtet ist, dann drücke fest auf das Gehäuseunterteil, um die vier versteckten Klammern darunter einrasten zu lassen. Du solltest das Einschnappen spüren und hören können.

  9. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Akkustecker freilegen: Schritt 9, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Akkustecker freilegen: Schritt 9, Bild 2 von 2
    • Ziehe vorsichtig das große Stück Klebeband ab, das den Akkustecker am Rand des Logic Boards ganz nah am Akku abdeckt.

    • Entferne das Klebeband.

  10. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 10, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 10, Bild 2 von 2
    • Ziehe vorsichtig das kleine Stück Klebeband ab, mit dem der Stecker des Datenkabels an der Akkuplatine abgedeckt ist.

    • Das Klebeband ist in das Flachbandkabel integriert und lässt sich nicht vollständig lösen. Ziehe es einfach so weit zurück, dass du an den Stecker herankommst.

  11. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 11, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 11, Bild 2 von 2
    • Mit der Spitze eines Spudgers kannst du jetzt die kleine schwarze Verriegelung umklappen, mit der das Kabel gesichert ist.

    Be very careful here. It is easy to break the whole connector off the battery board, which is what I did. Luckily the connector is part of the replacement battery, so you just need to remove the connector from the cable. The pictures here should provide more detail so you can see better what is going on.

    Mark Hayden - Antwort

    thanks a lot !!!!! great help :)

    der gute Geist - Antwort

  12. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 12, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 12, Bild 2 von 2
    • Schiebe das Datenkabel der Akkuplatine, aus seinem Anschluss heraus und trenne es ab.

    • Schiebe es parallel zum Logic Board in Richtung des Kabels.

    As simple as this step might seem, the golden leads will disapper the moment you remove it as it has some adhesive under the black strip that covers it. Ensure you peel it back enough to display the golden leads after swapping the batteries out.

    Harish Prasanna - Antwort

    Your battery may come with this ribbon cable. In that case, disconnect the other end.

    bencottrill - Antwort

  13. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 13, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 13, Bild 2 von 2
    • Biege das Datenkabel der Akkuplatine zur Seite, so dass es nicht mehr im Weg ist.

    I don't recall removing this cable from the laptop. I see that when actually putting the new battery in, the cable is attached already where it was detached and the right end needs to be reconnected.

    durphym - Antwort

    unfortunately the instructions to removing this cable are absent and I tried to pry the tab up instead of out and I damaged my board. Now no battery will work but it still functions with only with power cord. So be careful!

    Laloyd - Antwort

  14. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 14, Bild 1 von 1
    • Nimm einen T5 Torx-Schraubendreher und entferne die 3,7 mm Flachkopfschraube vom Stecker der Stromversorgung am Akku.

  15. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Akku abtrennen: Schritt 15, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Akku abtrennen: Schritt 15, Bild 2 von 2
    • Hebe jetzt den Stecker am Akkuanschluss mit einem Spudger vorsichtig an und trenne dadurch den Akku ab.

    • Hebe den Stecker so hoch an, dass er auch wirklich vom Anschluss getrennt bleibt. Wenn es im Laufe der Reparatur versehentlich zu einem Kontakt kommt, könnte dein MacBook Pro dadurch beschädigt werden.

    To completely avoid accidental contacts I recommend to wrap this connector in a piece of paper and hold it in place with tape.

    Do not put tape directly on the contact underside, as that may leave some glue that would affect the contact conductivity.

    Sergio Ballestrero - Antwort

    I put a piece of tape on the underside of the connector (sticky side up) to insure against accidental battery contact. If you put tape on the logic board side of the connection, some insulating padding material might accidentally stick to the tape when the tape is removed during reassembly.

    W. Smith - Antwort

  16. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierabdeckungen entfernen: Schritt 16, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierabdeckungen entfernen: Schritt 16, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierabdeckungen entfernen: Schritt 16, Bild 3 von 3
    • Entferne die vier 1,9 mm T3 Torx Schrauben, mit denen die Kunststoffabdeckungen über den Displayscharnieren befestigt sind.

    • Entferne die beiden Kunststoffabdeckungen über den Scharnieren.

    “T4 may be better.”

    -uBreakiFix Store Mgr.

    TJ Summerlin IV - Antwort

  17. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Hauptdisplaykabel entfernen: Schritt 17, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Hauptdisplaykabel entfernen: Schritt 17, Bild 2 von 2
    • Entferne die beiden 2,9 mm T3 Torx Schrauben, mit denen die Aluminiumabdeckung über dem Hauptdisplaykabel befestigt ist.

    • Entferne die Abdeckung.

    I had to use a T4 instead of a T3 to remove these ones

    Gianluigi Persano - Antwort

    Même chose, j’ai du utiliser du T4 au lieu du T3 !

    Ludovic - Antwort

  18. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 18, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 18, Bild 2 von 2
    • Entferne die beiden 1,7 mm T3 Torx Schrauben, mit denen die Aluminiumabdeckung über dem Displaykabel-Flexstecker befestigt ist.

    • Entferne die Abdeckung.

    t4 works better for these screws

    matthewfrey - Antwort

    T4 screw is correct

    Boy Named Kelly - Antwort

    stripped the freaking screw - now I'm screwed

    frangerestix - Antwort

  19. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 19, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 19, Bild 2 von 2
    • Heble das Displayplatinenkabel vorsichtig mit dem flachen Ende eines Spudgers gerade nach oben aus seinem Anschluss auf der Displayplatine ab.

  20. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit abschrauben: Schritt 20, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit abschrauben: Schritt 20, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit abschrauben: Schritt 20, Bild 3 von 3
    • Entferne die vier 1,5 mm T3 Torx Schrauben, mit denen die beiden Aluminiumabdeckungen über den beiden Displayplatinenkabeln befestigt sind.

    • Entferne die beiden Aluminiumabdeckungen mit einer Pinzette.

    T4 screws actually

    Boy Named Kelly - Antwort

  21. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 21, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 21, Bild 2 von 2
    • Entferne die vier 3,9 mm T5 Torx Schrauben (zwei auf jeder Seite), mit denen die Antennenkabeleinheit befestigt ist.

    • Entferne ebenfalls die zwölf 1,1 mm P2 Pentalobe Schrauben (sechs auf jeder Seite).

  22. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennekabel abtrennen: Schritt 22, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennekabel abtrennen: Schritt 22, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennekabel abtrennen: Schritt 22, Bild 3 von 3
    • Trenne die drei Koaxialkabel vorsichtig mithilfe einer Pinzette ab, indem du sie gerade nach oben vom Logic Board abhebelst.

    • Schiebe deine Pinzette oder das spitze Ende deines Spudgers unter jedes Kabel, bis du an den Anschluss kommst und drehe oder hebele dann vorsichtig, um es zu abzutrennen.

    • Um die einzelnen Kabel wieder zu verbinden, setze den Stecker direkt über seinen Anschluss und drücke ihn herunter, bis er einrastet.

  23. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 23, Bild 1 von 1
    • Entferne die 2,8 mm T5 Torx Schraube, mit der die drei Antennenkoaxialkabel an der Hauptplatine befestigt sind.

  24. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit hochhebeln: Schritt 24, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit hochhebeln: Schritt 24, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit hochhebeln: Schritt 24, Bild 3 von 3
    • Heble die Antennenkabeleinheit mithilfe eines Plektrums an den drei gezeigten Stellen heraus.

    • Schiebe das Plektrum nicht von einer Seite zur anderen, da sonst zwei Displaykabel beschädigt werden könnten.

  25. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit entfernen: Schritt 25, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit entfernen: Schritt 25, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Antennenkabeleinheit entfernen: Schritt 25, Bild 3 von 3
    • Entferne vorsichtig die Antennenkabeleinheit und ziehe dabei gleichzeitig das Kabelbündel unter dem Wärmerohr hervor.

    When refitting the antenna assembly be aware there’s a locating lug in the centre of the cavity that it needs to fit over. I slid it back in without noticing this on my first attempt and it leaves the screw holes about 1mm out of alignment and causes the assembly to slightly catch you when open/close the lid.

    David - Antwort

    Yes, totally thanks David, I had to disassemble and reassemble the Macbook because of this small metal "sheet". The screen was doing a small noise when I was opening it (a "poc")

    Paul Garcia - Antwort

  26. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen: Schritt 26, Bild 1 von 1
    • Entferne die Antennenkabeleinheit.

    • Drücke beim Zusammenbau die Kabel zusammen und führe sie unter das Wärmerohr in die richtige Position auf der Platine. Benutze, falls nötig, dein Werkzeug, aber wende nicht zu viel Kraft an.

    During reassembly, note the metal tab that holds down the cables (that was unscrewed in step 23) can get caught going back in. You have to lift it up. This step requires patience: you may have to attempt this several times.

    Clem Wang - Antwort

  27. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Displaykabeleinheit abschrauben: Schritt 27, Bild 1 von 1
    • Entferne die vier 3,9 mm T3 Torx Schrauben, mit denen die Federn der beiden Displaykabelabdeckungen befestigt sind.

    • Wenn die Federn der Abdeckung beim Zusammenbau nicht bis zu ihren Schraubenlöchern reichen, dann öffne das Display und ziehe sie weit genug heraus.

    T4 works better there !

    Paul Garcia - Antwort

    I guess it depends on your tools. Maybe a worn T4 would fit, mine wouldn't. T3 it is.

    maccentric -

    Torx T3 da 3,9 isn't easy to find it in a tool kit, damned

    pbs pbs - Antwort

  28. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Displaykabeleinheit entfernen: Schritt 28, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Displaykabeleinheit entfernen: Schritt 28, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Displaykabeleinheit entfernen: Schritt 28, Bild 3 von 3
    • Fasse die linke Seite der Displaykabeleinheit und ziehe sie zum unteren Ende des MacBook und weg von der Feder der Abdeckung.

    • Ziehe die Feder des Displaykabels mithilfe einer Pinzette aus ihrer Vertiefung.

    • Wiederhole diesen Schritt bei der rechten Feder an der Abdeckung der Displaykabeleinheit.

  29. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, MacBook öffnen: Schritt 29, Bild 1 von 1
    • Klappe das MacBook rechtwinklig auf.

  30. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, MacBook ablegen: Schritt 30, Bild 1 von 1
    • Lege dein MacBook vorsichtig so über eine Tischkante ab, dass das Display senkrecht nach unten zeigt.

  31. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharniere losschrauben: Schritt 31, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharniere losschrauben: Schritt 31, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharniere losschrauben: Schritt 31, Bild 3 von 3
    • Halte das Gerät mit der freien Hand fest, damit es nicht herunterfällt, und löse die Schrauben der Scharniere.

    • Löse die sechs Torx T8 Schrauben der Scharniere, aber entferne sie noch nicht.

  32. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display ganz öffnen: Schritt 32, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display ganz öffnen: Schritt 32, Bild 2 von 2
    • Halte das Gerät sicher am Tisch fest und klappe das Display ganz auf.

  33. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierschrauben entfernen: Schritt 33, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierschrauben entfernen: Schritt 33, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Scharnierschrauben entfernen: Schritt 33, Bild 3 von 3
    • Halte das Display mit einer Hand fest und entferne die sechs Torx T8 Schrauben der Scharniere mit der anderen Hand.

    • Passe auf, dass das Display nicht herunterfällt.

  34. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display absenken: Schritt 34, Bild 1 von 2 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display absenken: Schritt 34, Bild 2 von 2
    • Senke das Display ab.

  35. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Linkes Scharnier ablösen: Schritt 35, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Linkes Scharnier ablösen: Schritt 35, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Linkes Scharnier ablösen: Schritt 35, Bild 3 von 3
    • Achte darauf , dass das Display während der nächsten beiden Schritte immer gut abgestützt ist.

    • Halte das Hauptgerät des MacBooks mit einer Hand fest.

    • Drücke die linke Seite des Displays mit der freien Hand nach oben zum Boden des Laptops hin, um das linke Scharnier abzulösen.

    • Achte sehr darauf , dass der Stecker der Touch Bar beim Verschieben des linken Scharniers unbeschadet bleibt. Er kann leicht zerdrückt werden, die Touch Bar funktioniert dann nicht mehr.

  36. MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display entfernen: Schritt 36, Bild 1 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display entfernen: Schritt 36, Bild 2 von 3 MacBook Pro (13 Zoll, 2018, Touch Bar) Display tauschen, Display entfernen: Schritt 36, Bild 3 von 3
    • Löse das rechte Scharnier und entferne das Display.

Abschluss

Vergleiche dein Ersatzteil mit dem Originalteil. Möglicherweise musst du fehlende Teile übertragen oder Schutzfolien vom Neuteil abziehen, bevor du es einbauen kannst.

Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.

Entsorge deinen Elektromüll fachgerecht.

Lief die Reparatur nicht wie geplant? Verrsuche zuerst einige grundsätzliche Lösungen . In unserem Antwortenforum kannst du Hilfe bei der Fehlversuche finden.

28 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Tarun Thiruma

Mitglied seit: 11/20/19

35.219 Reputation

134 Anleitungen geschrieben

25 Kommentare

I followed all the steps and my new screen is working properly (•̀ᴗ•́)و. I realized however that my Touch Bar isn’t lighting up anymore… Did I forget to connect something?

Guy - Antwort

Where did you buy a replacement screen for your Mac? I can seem to find any for the A1989 Model that seems legit and I’m not sure how much I trust eBay listings.

Daniel Ramos -

Did you ever find an answer to this because I have had the same thing happen and I cannot for the life of me figure out why it has happened, what did you do to fix the problem or did you just give up and go to apple?

jack -

Unfortunately, my Touch Bar is still not working. I did some research back in 2020 and couldn’t find anything that would help fix this issue. And since my laptop is connected to an external screen and keyboard most of the time, it never really bothered me. But I should take it to Apple to see if it can be fixed and how much it’ll cost…

Guy -

I mean you may as well because what if it is just some simple calibration issue or some silly little thing that their diagnostic software can fix in less than a minute? If they try to charge too much money then you can always just deny, I believe that I will end up doing that soon to get a quote on just how much it will cost me to get both the display and Touch Bar repaired and see if it is worth it or not.

jack -

Ok so I would like to inform you that I did a little bit of digging into my MacBook Pro with its Touch Bar connectors and I have made the discovery that 1 one of those little chips near the connector I think they are resistors or diodes, idk but I found that one of them have literally exploded and killed another one next to it. I have no idea why or how but maybe you wanna check your MacBook Pro for that as well to see if its a common occurrence

jack -

I think you didn't read the VERY IMPORTANT comment by Marcelo on step 30. The long rectangle next to the pointy part of the "left" hinge (the one visible in the photo) is the connector for the touch bar and is EASILY DAMAGED, especially since you need a lot of force to get the hinge in.

I got around this by sliding the "left" hinge SIDEWAYS into its slot and then forcing the "right" hinge back.

Clem Wang -

Does anyone know where I can find a new official Apple Display 13” for model A1989? Can’t seem to find any except for eBay.

Daniel Ramos - Antwort

Yeah, I found mine on eBay. This vendor seemed trustworthy (www.ebay.com/usr/wallachee?_trksid=p2060353.m1438.l2754) and it turned out to be true. The screen I got is working perfectly…

Guy -

Après remplacement de l’écran complet.

Je confirme que ce tutoriel fonctionne également pour le MacBook Pro avec Touch Bar 13,3 “ de 2017 A1706

Attention: aux étapes 16-18-20-27 utiliser un embout Torx T4 et non T3.

Fajardo - Antwort

Aloha,

after replacing the screen the Keyboard backlight won’t work. Is it possible the T2 Chip will lock this function too?

Automatic backlight of screen and touchbar and True Tone don't work too.

Pete Doe - Antwort

I also had an issue with Touch Bar not working after the screen replacement, everything else works fine though.

Has anyone been able to figure out what causes the “TouchBar not working anymore” issue?

curio sus - Antwort

Like I asked the other guy, did you ever manage to find a fix for it? Because I am too having this issue

jack -

me too got the a1989 13” macbook pro. replaced the screen and touchbar screen is there but unresponsive to touch

jamie e - Antwort

I have the same issue but mine is due to me damaging a little chip near the connector. Maybe check your board over and make sure you didn't damage any chips in the process like I did

jack -

Can the MBP 13 intel Touch Bar work without the screen ? Like an Apple II

What happened if I left the screen connector unplugged ?

Phil B - Antwort

It does work, I did this with my own Mac and you can remove the screen and keep the functionality of the touch-bar. What you will loose is keyboard backlight so make sure that the brightness in software is at 100% for the touch-bar to be full brightness cos that won't change when you take the screen off

jack -

Merci Pour la clarté des explications 18/20

adama_ky - Antwort

Thank you very much for this tutorial, it is very clear!
I was able to swap out an A1989 failing screen by getting the working screen from a down A2159 Macbook Pro and all is ok : touchbar and keyboard backlight.

Yann C. - Antwort

me too got the a 1989 13” macbook pro. replaced the screen with a 2159 Model and then touchbar screen and touch does not work anymore at all.

Domi J. - Antwort

For people who had problem with the touch bar. Basically, the connector was damaged in the process of changing the screen.

https://www.youtube.com/watch?v=JNvuEPZh...

Marcelo Juliani - Antwort

Fan will not stop running after screen replacement. Tried resetting smc. No luck. Please advise. Thank you. MJ

M J R Consulting - Antwort

I got the fan to stop but the Touch Bar no longer works.

please advise.

M J R Consulting -

Pefekte Anleitung, Neues Display (auch die Touchbar) funktionieren wie Neu 😅😇 Danke 🤓

Kara Testma - Antwort

I swaped the screen following the 'purple gate' now my mbp is not booting anymore 😣 i checked twice every connections, all seems good... Any advice?

Oli Marcour - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 51

Letzte 7 Tage: 254

Letzte 30 Tage: 1,265

Insgesamt: 49,813