Einleitung
Wenn du das obere Gehäuse ausbauen willst, musst du fast jedes Bauteil aus deinem MacBook Pro entfernen. Du musst auch das Trackpad vom alten Gehäuse auf das neue übertragen.
Was du brauchst
-
-
Entferne die folgenden 10 Kreuzschlitz-Schrauben, die die Gehäuse-Unterseite des MacBook Pro 13" Unibody befestigen:
-
Sieben 3 mm Schrauben.
-
Drei 13,5 mm Schrauben.
-
-
-
Hebe die Unterseite vorsichtig an und drücke sie Richtung Rückseite des Laptops, um die Halterungsclips zu lösen.
In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...
It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)
Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.
Well . . . I ain't never done nuttin' like that, before!
Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.
Am I allowed to cry?
Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.
IFIXIT - IDIGIT!
HAHAHAHAHAHAHAHAHAHA.
That was a brilliant read.
Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.
Glad your Mac repair journey worked out.
:)
Cary B -
-
-
-
Löse mit der Kante eines Spudgers den Akkuanschluss nach oben, weg vom Sockel auf dem Logic Board.
How do you get that battery connector back on? Do you just press it in back in place after you're done?
yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).
This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,
-
-
-
Hebele den Stecker des Lüfters mit einem Spudger aus seinem Sitz heraus und gerade weg vom Logic Board.
I just soldered it back on. . . I tried to clean the pads with braid first, but it didn't do much so I don't think that's necessary. I first supper-glued it in place with the pins on the pads and then I put a tiny dab of solder on each pin/pad. Plugged in the fan and i works!
Just the answer I was looking for Ron! Awesome work buddy!
i recommend not to use the spudger. you damage more than by unpluggin the plug by hand. just simply pull the cable close to the plug of the old fan softly upwards out. the plug than comes easily out. put the new fan in and push the new plug by hand in. it is much easier than using a spudger. i also started with a spudger but nearly broke the plug out, so i watched a youtube tutorial and learned about it…
-
-
-
Entferne die folgenden drei Kreuzschlitzschrauben, welche den Lüfter am oberen Gehäuse befestigen:
-
Eine 6,5 mm Schraube
-
Eine 5,5 mm Schraube
-
Eine 4,5 mm Schraube
-
-
-
Fasse die Plastiklasche an, die am Sicherungsbügel des Displaydatenkabels befestigt ist, und drehe sie zur Seite des Computers mit der Gleichstromversorgung (DC-In) hin.
-
Ziehe den Stecker am Displaydatenkabel gerade aus seinem Sockel heraus in Richtung der Gleichstromversorgung (DC-In) des Computers.
-
-
-
Entferne die folgenden beiden Kreuzschlitzschrauben, welche die Halterung des Displaydatenkabels am oberen Gehäuse befestigen:
-
Eine 7 mm Schraube
-
Eine 5 mm Schraube
-
Hebe die Halterung des Displaydatenkabels aus dem oberen Gehäuse.
If you only want to replace the DC-in board, stop here and GOTO 17 (and DO NOT 4 and 6).
When the Logic board is loose, lift it up on the Harddrive end and shift slightly towards the HD, so that the USB connectors at the outside come free from under the case rim and the board can be lifted up a bit. Then there´s enough room to move the DC in board, pull the cable out with a pair of tweezers, wriggle it out from under the microphone cable and wriggle the new connector in. It can be pushed into the socket with tweezers or a small screwdriver. This worked perfect for me.
Be careful not to bend the logic board, but otherwise I think there´s much less risk of messing anything up with all the connectors and bits and pieces that need to be loosened and fastened.
-
-
-
Hebele mit dem flachen Ende des Spudgers den Stecker von Subwoofer und rechtem Lautsprecher vom Logic Board hoch.
-
-
-
Ziehe den Stecker am Kamerakabel in Richtung des optischen Laufwerks, um es vom Logic Board zu trennen.
There is a small piece just below this connector which is just an adhesive block to keep the connector from coming out. It is easiest to peel it up first with a fingernail or spudger then remove the cable. Likewise reinsert the cable before reapplying the adhesive safety stop.
I couldn't reconnect this cable correctly, so my camera is not working anymore.
It doesn't matter to me, I didn't used the camera that often...
But the Ambient Light Sensor uses the camera to control keyboard lighting, so I wasn't able to see my keyboard in the dark anymore... :(
If you have the same problem, after a couple of google hits I've found this app: https://www.macupdate.com/app/mac/22151/...
Problem solved! YAY!
PS: be careful because WIFI passes through this cable as well!!!!
Look at the photo intently. The connector is inserting not in parallel, but at a slight angle. The bottom corner of the connector is slightly ahead. It is important! Singular metod to insert it.
Vladimir -
-
-
-
Hebele die Stecker am Kabel vom optischen Laufwerk, der Festplatte und des Trackpads mit dem flachen Ende des Spudgers vom Logic Board hoch.
-
-
-
Klappe den Sicherungsbügel am ZIF Verbinder des Flachbandkabels zur Tastatur mit dem Fingernagel oder der Spudgerspitze hoch.
-
Schiebe das Flachbandkabel zur Tastatur mit dem Spudger aus seinem Sockel heraus.
When reinserting the keyboard ribbon cable, make sure you push it in all the way (two plastic tools are helpful - one to push it down flat, the other to coax it all the way in). For 3 days after replacing a top case, my MacBook Pro 13" wouldn't start up. I thought the main logic board was fried too. However, reinserting the keyboard ribbon cable again, this time perhaps 1mm farther in, and it started up again! I did the same for the "keyboard backlight ribbon cable" (i.e. reinserted it just to make sure). Really not sure which completed the circuit so is would start, but I suspect the keyboard ribbon cable.
Zitat von amiller770:
When reinserting the keyboard ribbon cable, make sure you push it in all the way (two plastic tools are helpful - one to push it down flat, the other to coax it all the way in).
I usually use a piece of sticky transparent office tape and stick it over the flat cable a bit further away from the mating part then pull on it. There is no better way to force the flat cable into a stiff connector without damaging the fragile cable.
As others have stated, if the keyboard ribbon cable isn't fully inserted the MBP will not power on. Leo Bodnar's recommendation to use a piece of transparent office tape did the trick for me. Many thanks Leo!
Inserting the ribbon cable for the keyboard was really difficult, but i was able to get it in using a piece of tape and pulling it up, just like the tape on the keyboard backlight.
Using a piece of tape is sheer genius Kelly. My mom once said her definition of genius was an idea that, when you hear it, you say to yourself, “now why didn’t I think of that?” But you never would have thought of it. Brava (or bravo) Kelly!
-
-
-
Ziehe das kleine Stückchen schwarzes Klebeband vom Sockel des Flachbandkabels der Tastaturbeleuchtung ab.
-
-
-
Klappe den Sicherungsbügel am ZIF Verbinder des Flachbandkabels der Tastaturbeleuchtung mit der Spudgerspitze hoch.
-
Schiebe das Flachbandkabel zur Tastaturbeleuchtung mit der Spudgerspitze aus seinem Sockel.
-
-
-
-
Hebele den Stecker am Kabel der Akkuanzeige mit dem flachen Ende des Spudgers vom Logic Board hoch.
-
-
-
Hebele das Mikrofon mit der Spudgerspitze aus der Klebeverbindung zum oberen Gehäuse.
-
-
-
Entferne folgende Kreuzschlitzschrauben:
-
Fünf 3,1 mm Schrauben
-
Zwei 3,9 mm Schrauben
-
Zwei 7 mm Schrauben vom DC-In Board
-
-
-
Entferne folgende Tri-point Schrauben, welche den Akku am oberen Gehäuse befestigen:
-
Eine 5,5 mm Schraube
-
Eine 13,5 mm Schraube
-
Hebe den Akku aus dem oberen Gehäuse.
-
-
-
Hebe das Logic Board an der linken Kante hoch und ziehe weiter daran, bis die Anschlüsse an der Seite des oberen Gehäuses frei werden.
-
Ziehe das Logic Board von der Seite des oberen Gehäuses weg und entferne es. Achte dabei darauf, dass sich das DC-in Board nicht verfängt.
When putting the logic board back in place, it's easier to angle the mic down in it's place as you are placing the board in, rather than after the board is seated.
-
-
-
Entferne die beiden Kreuzschlitzschrauben, welche die Halterung der Festplatte am oberen Gehäuse befestigen.
-
Hebe die Halterung aus dem oberen Gehäuse heraus.
-
-
-
Hebe die Festplatte an ihrer freien Kante hoch und ziehe sie aus dem Rahmen heraus, denke dabei an die Kabel, mit denen sie noch an den Computer angeschlossen ist.
-
-
-
Entferne folgende vier Kreuzschlitzschrauben, welche das Festplatten- und Infrarotsensorkabel befestigen:
-
Zwei 1,5 mm Schrauben
-
Zwei 4 mm Schrauben
-
Schiebe die Halterung der Festplatte und des Infrarotsensors weg von der Kante des oberen Gehäuses.
-
Löse vorsichtig die Kabel von Festplatte und Infrarotsensor vom oberen Gehäuse ab.
-
-
-
Entferne die beiden Kreuzschlitzschrauben, welche den Subwoofer am oberen Gehäuse befestigen.
-
Hebe den Subwoofer vom optischen Laufwerk weg und lege ihn über dem Computer ab.
-
-
-
Entferne die beiden 9,2 mm Kreuzschlitzschrauben, welche die Halterung des Kamerakabels am oberen Gehäuse befestigen.
-
Hebe die Halterung des Kamerakabels aus dem oberen Gehäuse.
-
-
-
Entferne die drei 2,5 mm Kreuzschlitzschrauben, welche das optische Laufwerk am oberen Gehäuse befestigen.
-
Hebe das optische Laufwerk an der rechten Kante an und ziehe es aus dem Computer.
-
-
-
Ziehe das kleine Stückchen schwarzes Klebeband ab, welches das rechte Lautsprecherkabel bedeckt.
-
-
-
Hebele den rechten Lautsprecher mit der Spudgerspitze aus der Klebeverbindung zum oberen Gehäuse.
-
-
-
Hebe die Einheit aus Subwoofer und rechtem Lautsprecher aus dem oberen Gehäuse.
-
-
-
Entferne die beiden äußeren 6 mm Torx Schrauben, welche jede Seite der Displayhalterung am oberen Gehäuse sichern. (Also insgesamt vier Schrauben)
-
-
-
Öffne dein MacBook so, dass Display und oberes Gehäuse einen rechten Winkel bilden.
-
Stelle dein MacBook so wie gezeigt auf einen Tisch.
-
Halte das Display und das obere Gehäuse mit der linken Hand zusammen. Entferne dann die 6 mm Torx Schraube von der unteren Displayhalterung.
-
-
-
Entferne die letzte verbleibende 6 mm Torx Schraube, die das Display am oberen Gehäuse befestigt.
-
-
-
Fasse das obere Gehäuse mit der rechten Hand und drehe es leicht in Richtung Oberkante des Displays, so dass die obere Displayhalterung von der Kante des oberen Gehäuses frei kommt.
-
Drehe das Display etwas weg vom oberen Gehäuse.
-
Hebe das Display hoch und weg vom oberen Gehäuse, achte dabei darauf, dass sich keine Halterungen oder Kabel verfangen.
-
-
-
Drücke vorsichtig das Trackpad an seiner Kante, die der Tastatur am nächsten liegt, aus seiner Aussparung im oberen Gehäuse heraus, aus den Rasten im oberen Gehäuse.
-
Fädle das Kabel zum Trackpad aus dem Schlitz im oberen Gehäuse heraus.
I concur with Anonymous 596. There is a support wall that runs front to back, under keyboard, held down by 2 Phillips screws that will need to be removed & transferred to new upper case. You can see it being touched by index finger in this pic.
-
-
-
Ziehe das Trackpad weg von der Außenkante des oberen Gehäuses.
-
Entferne das Trackpad und lege es beiseite.
There's a missing step here. In addition to the trackpad, there's an aluminum structural piece that sits under the center of the keyboard, that has to be migrated from old to new case. It's clearly shown to the left of the repair-person's right hand in step 44.
-
-
-
Befestige lose mit einem T6 Torx Schraubendreher die 1,1 mm Stellschraube, die mit deinem neuen oberen Gehäuse mitgeliefert wurde, im Schraubloch mit Abdeckung, in der Nähe Mitte der Öffnung für das Trackpad an deinem neuen Gehäuse.
I bought a used replacement case and had to move a few parts from the old case to the replacement. This included the battery indicator cable, the clips for the trackpad and the bracket in the center of the top case. So worth it at this point to compare your old and replacement case to be sure everything you need is there.
my new case came with the set screw already installed, and i couldn’t loosen it. i didn’t want to strip it and cause a bigger problem, so i left it alone. the trackpad seems to work fine so far regardless, although i may take the bottom case off and play with it a little if i get a chance.
i also (just like Ron) had to move the trackpad clips, battery indicator and center bracket to the new case. they were not included.
-
-
-
Führe sorgsam das Kabel deines alten Trackpads durch den schlitzförmigen Einschnitt in deinem neuen oberen Gehäuse.
-
Halte mit einer Hand das Kabel zum Trackpad fest, während du die beiden Haltelaschen an der Außenkante des Trackpads unter der Lippe am oberen Gehäuse befestigst.
-
Ziehe am Kabel des Trackpads, während du das Trackpad in seiner Öffnung im neuen oberen Gehäuse einsetzst.
-
-
-
Setze in jedes der äußeren Bohrlöcher im Trackpad eine 1,2 mm Kreuzschlitzschraube ein. (Insgesamt zwei)
-
-
-
Versuche fortwährend dein Trackpad zu klicken und ziehe dabei vorsichtig die Torx T6 Stellschraube an, bis die Klicks sich anfühlen, wie beim Neugerät.
-
-
-
Drehe dein oberes Gehäuse herum, so dass die Tastatur oben liegt.
-
Richte das Trackpad mittig in seiner Öffnung im oberen Gehäuse aus.
-
-
-
Ziehe die äußeren beiden Schrauben an der Innenkante des Trackpads an und überprüfe an der Außenseite des oberen Gehäuses, ob das Trackpad noch richtig sitzt.
-
Wenn es gut ausgerichtet ist, dann kannst du die restlichen Kreuzschlitzschrauben an der Innenkante des Trackpads anbringen.
-
Überprüfe vor dem Zusammenbau deines Laptops nochmals, ob die Einstellung der Stellschraube immer noch richtig ist, so dass die Maus korrekt klickt.
You can actually replace the keyboard alone fairly easily! I don't know why everyone says you have to replace the whole top case, because if you've got the guts to go this far, you might as well just peel back the illuminator cover and get to work pulling all those tiny screws in the keyboard... Just be careful when peeling up the black adhesive keyboard cover, because you will need to replace it. I used the edge of the ifixit Sesame tool (very thin flat metal opening tool) to carefully slip under any bits of adhesive, and had the keyboard exposed in no time. Also be careful because the clear plastic sheet is actually the keyboard illuminator. Once under all that, it's a mere 50 or so tiny screws, 2 screws in the power button backing, and you've got the keyboard out. Use a magnetized #000 phillips, it will make life much easier than anything else.
Absolutely right. I just replaced a keyboard the same way without much problem but i just want to add that those tiny screws need extra care as the heads can get damaged very easily. If damaged, they become very difficult to remove.
Masood -
I did just that on my mid-2010 MacBook Pro about a month ago and sadly will have to do it to my wife's Early-2011 one next week. I was cleaning all the crap off her keyboard and apparently nuked the K and 0 keys on her keyboard. Probably my ply challenge was aligning the keyboard illuminator. It's still not aligned properly on mine so some keys are better lit than others, but otherwise it was a relatively easy fix and far cheaper than replacing the entire upper case.
I replaced my keyboard less than an hour ago. The biggest pain/most time consuming was reattaching the ZIF connector for the keyboard and backlight. No matter what I did I could not get the %#*@ thing to reattach. What sadist designs these things? I had to walk away from the project for an hour and finally success.
All those screws will make you go crosseyed!
It helps to put some tape along the cable going lengthwise to the cable, and then fold the end of the tape onto itself to give yourself something to hold onto. This will give you some leverage to get that puppy into the socket.
I’m glad you managed !!!
I’m suffering :( take a part about 5 times…… ordered new (used) keyboard, the same results. I tested logic board in my daughter MAC, board works 100% no trouble ……. what could be wrong? there a secret how to reassemble keyboard parts together? I ripped a little bit black plastic thing, not top one with tiny connectors……
In the end I have two keyboards, cleaned and taken a part, both of them acting identical when installed. Some keys respond by giving absolutely not relevant symbols, beeping noise come with almost every key i pressed…..
Recovering after massive cappuccino spell after surprising hug :(((((
I swear to post photo step by step, if I will achieve this one……….. assemble back to 100% working condition after total reassembling, ultrasonic cleaning and drying………. just keyboard panel.
Give me nightmares :) will be first time I have so much trouble to fix………
I'm wondering about putting it back together. Different wires and small parts etc were glued or adhered in some way to the case or sides or whatever, as it is put together in the beginning. Is that just to make it easier to put it back together? Should I try to stick them back the way they were with something? Can you use tape or glue if it's just a wire? I wouldn't want to use something that would melt...or is this not something to worry apout?
I just used 1/4 polymide tape, and iFixit double sided tape. Works like a champ.
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
47 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
2 Kommentare
Very good tutorial. Guide was 100% accurate. As mentioned, make sure you have good quality tools, and follow the guide to be certain the right get tool is used for certain screws, I did strip one screw head, in my opinion not bad considering all the tiny screws! But now my MacBook works, and save me having to spend on a new MacBook!
Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.
David Kilbridge - Antwort
Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.
mastover - Antwort
I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.
adlerpe -
That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.
joyitsjennie -
Great idea and one I use often
Thomas Overstreet -
Excellent idea! Thanks for sharing it here.
Laura Sharkey -
I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm
valentinedhdh - Antwort
I use a magnetic mat and place the screws in order on that :)
Cary B - Antwort