Zum Hauptinhalt wechseln

MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen

Was du brauchst

Einführungsvideo

  1. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen, Akku: Schritt 1, Bild 1 von 1
    • Ziehe mit deinen Fingern beide Laschen vom Akku weg und hebe den Akku aus dem Computer heraus.

    Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

    rpbetancourt - Antwort

    If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

    Adam - Antwort

    Zitat von Adam:

    If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

    Thank you very much!

    Evgeniy - Antwort

    When I did this, I used a empty egg carton to store my screws. I wrote the steps where I removed screens in Sharpie on the bottom of the "egg cup" and then dropped the screws in as I went. Then I just worked backwards to put it all back together.

    mark93 - Antwort

    Zitat von rpbetancourt:

    Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

    I Generally just use a piece of paper with a rough sketch of the system and locations of the screws with prestik.

    Tarn Alcock - Antwort

  2. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen, RAM-Abdeckung: Schritt 2, Bild 1 von 1
    • Entferne die drei identischen Kreuzschlitzschrauben von der RAM-Abdeckung.

    • Denk daran, den Überblick zu behalten, welche Schraube du wo entfernt hast. Das hilft dir später beim Zusammensetzen.

  3. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 3, Bild 1 von 1
    • Hebe die Abdeckung gerade genug an, um sie gut greifen zu können, und ziehe sie zu dir hin vom Gehäuse weg.

  4. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen, Oberes Gehäuse: Schritt 4, Bild 1 von 1
    • Entferne die beiden Kreuzschlitzschrauben im Akkufach in der Nähe der Verriegelung.

    Getting these screws in and out is difficult because most screwdrivers are longer then the battery compartment is deep and so will be slightly off plumb. When you go to re-assemble the computer, getting these screws to seat is one of the hardest parts of the re-assembly. It's very important to be gentle and not to strip the threads.The screw should tighten and come to a stop after 3-4 turns. If you turn 6 or more turns and don't feel it grab, then back off and try again, making sure that everything is in alignment.It might be easier to start with the left screw, because it is further away from the latch mechanism.

    dalphotography - Antwort

  5. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 5, Bild 1 von 1
    • Entferne die folgenden 6 Schrauben:

    • Zwei 10 mm T6 Torx-Schrauben auf beiden Seiten des RAM-Steckplatzes.

    • Vier 14,5 mm Kreuzschlitzschrauben entlang des Scharniers.

    A T6 worked but was too small. A T7 was better.

    nrpardee - Antwort

  6. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 6, Bild 1 von 1
    • Entferne die vier Kreuzschlitzschrauben an der Seite des Computers mit den Anschlüssen.

    Be careful when reassembling your laptop -- do not put the screw into the DVI port! It will not come out.

    Scott Rose - Antwort

    Been there, done that!
    I honestly don't remember how did I ultimately succeeded in getting that %#*@ screw back from the hole...

    maxime.abbey -

    by Scott Rose Jan 4 @ 11:12 PM

    Be careful when reassembling your laptop -- do not put the screw into the DVI port! It will not come out.

    To keep this from possibly happening, I placed 2 pieces of tape over the DVI connector pin holes.

    rpbetancourt - Antwort

    Be careful in step 4, these two screws are shorter than the four screws in step 6, dont mix them up!

    brendantully1 - Antwort

    If you still have the DVI to VGA adapter that came with the computer plug it in to the plug and screw it tight, that way you will not put one of the screws into the holes.

    netdude21 - Antwort

  7. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 7, Bild 1 von 1
    • Drehe den Computer um 90 Grad und entferne die beiden Kreuzschlitzschrauben auf der Rückseite des Computers.

  8. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 8, Bild 1 von 1
    • Drehe den Computer erneut um 90 Grad und entferne die vier Kreuzschlitzschrauben an der Seite des Computers.

  9. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 9, Bild 1 von 1
    • Ziehe das obere Gehäuse nicht vorschnell ab. Das Gehäuse ist über ein Flachbandkabel mit dem Logic Board verbunden.

    • Hebe das Gehäuse an der Rückseite an und fahren Sie mit den Fingern an den Seiten entlang, um das Gehäuse zu lösen.

    • Sobald die Seiten abgelöst sind, musst du das Gehäuse möglicherweise auf und ab bewegen, um die Vorderseite des oberen Gehäuses zu lösen. Dieser Schritt kann recht knifflig sein. Über dem DVD-Laufwerk befinden sich 4 zurückgesetzte Laschen, die sich vertikal herausziehen lassen.

    • Beachte, dass sich die beiden kleinen Ausstülpungen an der linken Vorderseite des oberen Gehäuses beim Entfernen des oberen Gehäuses verbiegen können. Beim Wiedereinbau musst du sie möglicherweise zurückbiegen, damit sie in die Rillen im unteren Gehäuses passen.

    there are 2 push buttons inside the harddrive bay which release the front of the upper case.

    mforgie - Antwort

    this is an annoyingly difficult step. it is VERY hard to get the front part off without bending the unit improperly. Would be great to know where the two "push buttons" are.

    lessig - Antwort

    On my MacBook, there were no pushbuttons. Rather, two mini phillips screws were holding the case on inside the battery bay. The two screws are under two ball-bearing-like nubs that help hold the battery in the bay.

    khank - Antwort

    Zitat von khank:

    On my MacBook, there were no pushbuttons. Rather, two mini phillips screws were holding the case on inside the battery bay. The two screws are under two ball-bearing-like nubs that help hold the battery in the bay.

    I just realized these were the screws mentioned in Step 4, which I missed originally. Did you miss step 4 too?

    khank - Antwort

    I discovered that I didn't need to take the case off completely. I just propped it up with a small screwdriver and was able to remove the airport card and replace it with a new one fairly easily.

    schemedream - Antwort

    That's not so difficult step. you shoul know , that front edge of upper case holding only on 5 plastic "locks" 4 in front edge upon the superdrive, 5-th near the "sleep light, open laptop button"

    just lift up the rear edges of upper case to 35-40 degrees

    Hofmann78rus - Antwort

    [I d just say carefule on the prising open - these are fragile screw tab fixings joined to the uppercase. - Patience and gentle pressure and all works fine .

    daithid - Antwort

    Getting the top case off, especially right above the optical drive slot was a @#$%^. !^$%. Was finally able to work it loose by twisting in the budger. Be careful.

    Archhawk - Antwort

    the two push pins are in the battery area behind the front of the open button

    mykeylynx - Antwort

    Zitat von Archhawk:

    Getting the top case off, especially right above the optical drive slot was a @#$%^. !^$%. Was finally able to work it loose by twisting in the budger. Be careful.

    I agree! It was really very difficult just ROCKING the front panel. NOT done! Do not pry it from the front of the unit, as the soft metal edge gets scratched! I turned the unit upside down and slowly pried the keyboard apart left-to-right from INSIDE the Battery Bay, slipping a plastic pen to keep it apart. When I finally looked at what was holding it down, it was these 5 grey&black plastic SNAP slots, and 4 of them were behind the DVD slot.

    http://www.facebook.com/photo.php?pid=40...

    Mario da Silva - Antwort

    I found I had to push with a little force from underneath the battery compartment where the touch pad is located to free the bottom edge of the case. The case came away with two loud snaps. At first I thought I'd broken something, but then it appeared that it was just the plastic above the slot loading super drive that was held in very tightly and needed some encouragement.

    Joshua May - Antwort

    There are several clips along the front of the case in front of trackpad and above the optical drive slot. These need to be gently levered open (eg using an old credit card), and clipped closed on reassembly. Start at the left hand side. Take care not to bend the aluminum top. When reassembling, check the top panel for kinks/bends and straighten by hand before reassembly.

    cheongi - Antwort

    The way I did it was to lift the back to about 45% (the ribbon cable is long enough) and then used the spudger to force the 4 snap tabs in front of the optical drive to separate, working from the right edge towards the middle (they will 'pop'), ending with the last tab to the left of the sleep light.

    Hilal Malawi - Antwort

    After reading all the step 9 comments I was prepared for it to be very difficult. The two bendable tabs on the left front of the case were no bigger than 1/4 inch wide each and caused no trouble taking it off or putting it back on. Lifting the cover off happened before I knew it. I was carefully lifting the cover from side to side and 'poof' it was off and the yellow ribbon attaching between the case and the keyboard was so old and brittle it parted ways without my permission so that took care of step 10 right there but no problem.

    Being prepared, reading the guide, printing the guide, taping each screw to the right place on the guide made it all easy. I'm amazed it went so smooth on the first run-through. Thanks iFixit!

    Sally - Antwort

  10. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 10, Bild 1 von 1
    • Trenne das Flachbandkabel des Trackpads und der Tastatur vom Logic Board ab und entferne, falls nötig, das Klebeband.

    • Entferne das obere Gehäuse.

    not necessary. just attach a string around both the screen and the keyboard. it will stay in a steady position..

    -urdus.

    urdus - Antwort

    I found that the ribbon connecting the top part of the case to the logic board wasn't long enough and the connector did have to be disconnected.

    Joshua May -

    Zitat von urdus:

    not necessary. just attach a string around both the screen and the keyboard. it will stay in a steady position..

    -urdus.

    Excellent tip! Thanks, this allowed me to skip steps 10 and 11 (any unnecessary tinkering with the logic board is recommended).

    rpbetancourt - Antwort

  11. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen, Festplatte: Schritt 11, Bild 1 von 1
    • Trenne das orangefarbene Flachbandkabel der Festplatte vom Logic Board.

    you dont need to do this. disconnect the sleeplight and IR sensor connectors instead. Just lift the harddrive cable where it is glued. It can still be connected to the logicboard. Dont lift the harddrive too much when disconnecting it.

    urdus - Antwort

    I fully agree with urdus. Step 11 is un-needed when replacing the harddrive.

    sanjaygovindjee - Antwort

    Zitat von urdus:

    you dont need to do this. disconnect the sleeplight and IR sensor connectors instead. Just lift the harddrive cable where it is glued. It can still be connected to the logicboard. Dont lift the harddrive too much when disconnecting it.

    philip Aronson - Antwort

    Yikes! I did Step 11 and now I have loose ribbon cable. How do I attach it back? Do I have to solder it?

    bruce vivero - Antwort

    I agree with Urdus... less one step if you're careful enough...

    Mario da Silva - Antwort

    I also removed this ribbon, (while actually trying to clean my fan, it was ignorantly done...) anyways, now my hard drive is not recognized when I startup... How do I reconnect this?? Please help...

    Chase - Antwort

  12. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 12, Bild 1 von 1
    • Verwende einen Spudger, um den Kleber, mit dem die Anschlüsse für das Sleep-Light und den IR-Sensor an der Oberseite der Festplatte befestigt sind, vorsichtig zu lösen.

    This was a pain in the !!* for me. It was really stuck on the original drive but good. In finally getting it off, the connector came out of the bluetooth. I had to CAREFULLY slide the ribbon connector back into the bluetooth card. Not easy to do with my big fat fingers.

    Archhawk - Antwort

    I didn't have a budger/spudger, so I cut the brush side off a used plastic toothbrush and used the handle after sharpening the cutoff end into a wedge... works great!

    Mario da Silva - Antwort

    I use UN-DU scrapbookers adhesive remover <http://un-du.com/>. (It is hexane.) It temporarily dissolves adhesive bond, then evaporates and the adhesive is sticky again. Much less risky than a spudger.

    cheongi -

    Agreed! Two hugely tricky steps here. The larger of the two components really did NOT want to come away from the hard drive case (I was afraid of tearing the ribbon cable), AND I accidentally pulled the Bluetooth ribbon out from the case. Heck of a job to replace it! Anyone know where I can get the opaque plastic sheath for the Bluetooth board?

    dave - Antwort

    The whole replacement was easy "Stevie Wonder" could of done this! Make sure that the you are careful with the IR sensor and sleep light and it should be noted the the screw to remove HDD seating bracket is directly under a few wires.

    nshardyjr - Antwort

  13. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 13, Bild 1 von 1
    • Entferne die beiden silbernen Kreuzschlitzschrauben, mit denen die Festplattenhalterung am unteren Gehäuse befestigt ist.

    • Bei einigen Geräten können diese Schrauben T6 Torx Köpfe haben.

    in my version, the screws are TORX

    lupuss - Antwort

    these were Torx T-6 in my case

    Dan - Antwort

  14. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 14, Bild 1 von 1
    • Schiebe die Bluetooth-Platine aus ihrem Steckplatz neben der Festplatte heraus. Die Bluetooth-Platine ist noch mit dem orangefarbenen Festplattenkabel verbunden, versuche also nicht, sie ganz aus dem Computer zu entfernen.

    no Bluetooth board here

    lupuss - Antwort

    torx and no bluetooth board- late 2007 mbp.

    also, orange cable seems attached all the way across and drive wont come up on left side.

    Nick - Antwort

    Torx and no bluetooth card in MBP from March 2008.

    Nicolai Fabritius - Antwort

    I couldn't figure out how to 'slide' the Bluetooth board out, so I just left it in place and pulled the hard drive out.

    Hilal Malawi - Antwort

  15. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 15, Bild 1 von 1
    • Hebe die Festplatte mit einer Hand an und entferne mit der anderen Hand die Halterung von der Seite der Festplatte.

    NOTE TO ORIGINAL MBP CORE DUO OWNERS: This picture makes it look like the retaining bracket comes off when you lift out the hard drive at this point, but it does NOT. The bracket is attached to the hard drive via 2 Torx screw (step 17), which must first be removed.

    Curtis Wayne - Antwort

    When reinserting the hard drive careful not to snag the bluetooth board cable on the bottom right side of the hard drive.

    milo - Antwort

  16. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 16, Bild 1 von 1
    • Trenne das orangefarbene Festplattenkabel ab.

    • Vergewissere dich nach dem Einbau der neuen Festplatte, dass die Lüftungsöffnung (oben) nicht durch das orangefarbene Flachbandkabel verdeckt wird.

    in my version the left side rubber bumpers are locked in the casing of the MBP and you have to slide out the unit to the right

    lupuss - Antwort

    Zitat von lupuss:

    in my version the left side rubber bumpers are locked in the casing of the MBP and you have to slide out the unit to the right

    As were mine.

    cgollner - Antwort

    My new Hitachi drive has the "do not cover" hole right under the place where the IR and sleep sensors need to be attached. The stock drive had the hole on the other end of the hard drive. I just made sure the adhesive didn't seal off the hole, and I think it should be alright. Otherwise, install was easy and these directions were outstanding. Thanks.

    kkir - Antwort

    I had the same problem with my Western Digital Scorpio 2.5in 500GB SATA 16MB. Otherwise, the instructions were awesome. I had to have the tape "just" left of the breather hole and the ribbon cable wasn't flush, but I don't think it's too big a deal. Drive was recognized by the laptop immediately and good old Time Machine restore is on its way.

    Arthur Lee -

    Thanks, I managed to put a new 320 GB drive in. Next I partitioned the drive for MAC OS 10.4 and Windows with Disk Utility. Selected Volume Format: Mac OS Extended (Journaled) for Mac OS 10.4 and MS-DOS File System for Windows. Next I restored Mac OS 10.4 with Carbon Copy from the old 100 GB drive, BUT how to restore Windows?@#$%^&* Carbon Copy doesn't do that.....??

    Barbara - Antwort

    Zitat von Barbara:

    Thanks, I managed to put a new 320 GB drive in. Next I partitioned the drive for MAC OS 10.4 and Windows with Disk Utility. Selected Volume Format: Mac OS Extended (Journaled) for Mac OS 10.4 and MS-DOS File System for Windows. Next I restored Mac OS 10.4 with Carbon Copy from the old 100 GB drive, BUT how to restore Windows?@#$%^&* Carbon Copy doesn't do that.....??

    My new SATA 500GB Hitachi was Initialised and Partitoned with Disk Utility when inside an external USB box ($20.00), and then all the contents of the 80GB was CCC'd over. When the new drive was switched over and tested before reassembly, everything came up identical to the original HD. (but I don't use Windows)! Kudos to CCC, and this site for clear instructions! Thanks, Guys/Gals.

    Mario da Silva - Antwort

    On my MBP, the orange cable was glued for it's length on the top of the original drive. Rather than try to peal it off, I removed the sticker underneath which was easier as the orange cable came with it. It also made putting it back easier.

    Stephen Spicer - Antwort

  17. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen, Festplatte: Schritt 17, Bild 1 von 1
    • Entferne die beiden silbernen T6-Torx-Schrauben und die schwarzen Gummipuffer an der rechten Seite der Festplatte.

    • Du musst diese Schrauben und Puffer auf deine neue Festplatte übertragen, wenn du das Laufwerk ersetzt.

    On my macbook the bumpers are white and the screws are silver. Note that the bumpers are different on the right side than the left side in size as well!

    David Rees - Antwort

  18. MacBook Pro 15" Core Duo Modell A1150 Festplatte tauschen: Schritt 18, Bild 1 von 1
    • Entferne die beiden schwarzen T6 Torx Schrauben und die schwarzen Gummipuffer an der linken Seite der Festplatte.

    • Du musst diese Schrauben und Puffer auf deine neue Festplatte übertragen, wenn du das Laufwerk ersetzt.

    • Wenn du eine neue Festplatte installierst, ist hier eine Anleitung zur Installation von OS X, damit du sofort loslegen kannst.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.

534 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

iRobot

Mitglied seit: 09/24/09

1 Reputation

636 Anleitungen geschrieben

8 Kommentare

i found that i needed to "rock" the upper case left to right, not up and down, in order to remove it. and although i was trying to be careful, the keyboard ribbon cable was so tight that the connection popped off when i released the upper lid. took a minute to find the connection on the logic board.

when i was removing the hard drive, for whatever reason, there was no bluetooth board on top of the retaining bracket.

other than that, the directions were fantastic. i'll recommend you to all my friend!

the only sad part is that it turned out the hard drive was not the source of the "rice crispies" noise, which is what sent me on this journey in the first place. i now think it's the right-hand fan. whoo hoo! more maintennance!

thanks again,

steve shelley

Steve Shelley - Antwort

Even better than little bags or a sorting tray--get an old egg carton, 12 or 18, and use a Sharpee to mark the step number on each egg holder. That way, bumping the table won't screw up your sorting, and you can easily find the right screws in the right order.

Bruce campbell - Antwort

Worked for me exactly as shown! Thank You!

Mark Adsit - Antwort

One thing that was not mentioned is if you are upgrading to a larger capacity hard drive from the original, you can clone the original hard drive (if it hasn't crashed) to the new one then do the swap. You can then use the Universal Drive Adapter to format the smaller drive and use it as you wish.

netdude21 - Antwort

Hello, I do not have the disc with which to replace my OS, it is lost. Will the above videos address this issue? Is it possible to replace an OS once the original disk is lost? Thanks!

jennifer - Antwort

This guide is stunningly useful. I recommend opening the primary guide in one window, and the comments (For each step) in another, and scrolling together--the user comments are VERY helpful, including steps that can be skipped.

uno clay - Antwort

I followed the instructions exactly and after replacing the drive the device won’t start fully. All I hear are the fans turning on, DVD drive noise and the light on the front displays. No audio and nothing on the display, totally black , not even a flicker. Any thoughts as to what I might have done wrong or damaged? Hopefully someone knows how to fix this? Thanks

Mathew Wade - Antwort

Don’t Loose Any Screws! This is a very good Guide for swapping out your drive. I cloned my old drive before I swapped it out using a cheep USB drive case and downloaded clone software and I had no issues.

mkeehnel - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 6

Letzte 7 Tage: 24

Letzte 30 Tage: 148

Insgesamt: 803,005