Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
-
Ziehe mit deinen Fingern beide Laschen vom Akku weg und hebe den Akku aus dem Computer heraus.
-
-
-
Entferne die drei identischen Kreuzschlitzschrauben von der RAM-Abdeckung.
-
-
-
Hebe die Abdeckung gerade genug an, um sie gut greifen zu können, und ziehe sie zu dir hin vom Gehäuse weg.
-
-
-
Entferne die beiden Kreuzschlitzschrauben im Akkufach in der Nähe der Verriegelung.
-
-
-
Entferne die folgenden 6 Schrauben:
-
Zwei 10 mm T6 Torx-Schrauben auf beiden Seiten des RAM-Steckplatzes.
-
Vier 14,5 mm Kreuzschlitzschrauben entlang des Scharniers.
-
-
-
Entferne die vier Kreuzschlitzschrauben an der Seite des Computers mit den Anschlüssen.
-
-
-
Drehe den Computer um 90 Grad und entferne die beiden Kreuzschlitzschrauben auf der Rückseite des Computers.
-
-
-
Drehe den Computer erneut um 90 Grad und entferne die vier Kreuzschlitzschrauben an der Seite des Computers.
-
-
-
-
Hebe das Gehäuse an der Rückseite an und fahren Sie mit den Fingern an den Seiten entlang, um das Gehäuse zu lösen.
-
Sobald die Seiten abgelöst sind, musst du das Gehäuse möglicherweise auf und ab bewegen, um die Vorderseite des oberen Gehäuses zu lösen. Dieser Schritt kann recht knifflig sein. Über dem DVD-Laufwerk befinden sich 4 zurückgesetzte Laschen, die sich vertikal herausziehen lassen.
-
Beachte, dass sich die beiden kleinen Ausstülpungen an der linken Vorderseite des oberen Gehäuses beim Entfernen des oberen Gehäuses verbiegen können. Beim Wiedereinbau musst du sie möglicherweise zurückbiegen, damit sie in die Rillen im unteren Gehäuses passen.
-
-
-
Trenne das Flachbandkabel des Trackpads und der Tastatur vom Logic Board ab und entferne, falls nötig, das Klebeband.
-
Entferne das obere Gehäuse.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger to pry up the translucent plastic sheath covering the keyboard connector.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the tip of a spudger to flip up the black plastic flaps locking down the keyboard and keyboard backlight ribbon cables.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Slide the orange keyboard backlight ribbon out of its connector.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Peel up the orange tape covering the keyboard backlight connector.
-
Use the tip of a spudger to flip up the brown plastic flap locking down the keyboard backlight ribbon cable.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger or your finger to slide the keyboard backlight ribbon out of its connector.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Carefully peel up the orange ribbon cable which carries the power and sleep signals, removing tape as necessary
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Peel back the black protective sheath on the right side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Peel back the black protective sheath on the left side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the ten identical Phillips screws attaching the keyboard to the casing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
There are four locking tabs along the back edge of the keyboard holding it in place. These tabs must be straightened before you can remove the keyboard.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
The first frame shows a tab in the "locked" position and the second frame shows the same tab in the "unlocked" position.
-
Use needlenose pliers or a spudger to bend each of the four tabs so that they are all in the "unlocked" position.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Slide the keyboard ribbon out of its connector.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Place the upper casing on its edge and use a spudger to push the keyboard away from the casing, poking the spudger through the central keyboard screw hole. Grasp the keyboard as it separates from the casing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Maintaining your hold on the keyboard, lay the casing flat and gently bow the keyboard until the two tabs on either side of the keyboard come free.
-
Slide the keyboard away from the trackpad and out of the upper case.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
78 weitere Nutzer:innen haben diese Anleitung absolviert.
5 Kommentare
Forget plastic bags...I use a muffin tin, such as that used for baking, and put the screws from each step in successive muffin holes. When I reverse, I just back up the order.
GENIUS. Thanks!
aubush09 -
no pic
Step 13 is totally unnecessary as you don’t need to remove the cable entirely.